Raypak B0147, B0109 Connections Electrical, Thermostat Setting, 109 147 On/Off, External Controls

Page 22

CONNECTIONS – ELECTRICAL

All electrical work and permanent wiring must be carried out by a qualified person and in accordance with the Wiring Rules AS/NZS 3000 and local authority requirements.

The water heater is supplied with a 1.8 metre lead and plug and requires a 240 V 50 Hz general purpose outlet (GPO) to be located within 1.0 metre of the installation. NOTE: For outdoor installations the GPO must be weatherproof. The GPO must be clear of the flue exhaust, draining water, gas supply pipe and water connections.

The water heater must be properly earthed and the installation of a Residual Current Device (RCD) is recommended for added electrical safety

CAUTION: DO NOT LOCATE CABLES IN FRONT OF OR UNDERNEATH THE BURNER.

Where conduit is mounted to the water heater a 10mm air gap must be maintained from the water heater casing to eliminate possible overheating. DO NOT locate conduits or cables where they will obstruct or restrict removal of panels, access doors etc.

The water heater must NOT be able to operate without the pump running.

The water heater and pump may be supplied from the same electrical circuit, alternatively the 240 volt supply to the water heater may be provided via auxiliary contacts of the pump contactor or relay (if fitted).

Where additional control wiring is connected to the water heater, which is not isolated by the GPO, a suitable warning label must be affixed to the water heater identifying the isolation point for that particular wiring (e.g. by circuit breaker or fuse number and switchboard identification number or location).

THERMOSTAT SETTING

The thermostat is adjustable; the range varies according to the capacity and operation type (refer to the table opposite).

109

147

On/Off

25°C - 95°C

20°C - 80°C

Hi/Lo

45°C - 85°C

0°C - 95°C

For reasons of safety and economy, we recommend that the thermostat is set at the lowest temperature that will provide sufficient hot water. Discuss the thermostat setting requirements with the householder or responsible officer. Refer to “Temperature Control” on page 35.

INTERMITTENT PUMP OPERATION

For applications utilising intermittent pump operation a pump run on timer is fitted as standard equipment to the water heater and must be utilised to prevent nuisance tripping of the high limit thermostat due to heat build up in the heat exchanger. The timer should be set to allow the pump to operate for at least ten (10) minutes.

EXTERNAL CONTROLS

The water heater can be wired for use with an external flow switch, remote control thermostat or a remote time switch.

To connect an external switch, time clock or thermostat to the water heater it is necessary to remove the bridging wire between terminals 1 and 2 of the water heater terminal block and connect the external control across these two terminals(refer to the diagram opposite and to the wiring diagrams on pages 24 to 27).

To connect a flow switch to the water heater it is necessary to remove the bridging wire from between terminals 3 and 4 of the water heater terminal block and connect the flow switch across these two terminals (refer to the diagram opposite and to the wiring diagrams on pages 24 to 27).

Where an external thermostat is utilised the water heater thermostat should be adjusted to a temperature higher than the setting on the remote thermostat (Refer to "Temperature Control" on page 35.

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Raypak Water Heaters Patents Contents Model Type Temperature AdjustmentAbout Your Water Heater HOW HOT should the Water BE?What to do if YOU Smell GAS? SafetyTo Turn OFF the Water Heater Does the Water Quality Affect the Water Heater HOW do I Know if the Water Heater is Installed CORRECTLY?To Turn on the Water Heater HOW Long will the Water Heater LAST?Models HOW Your Water Heater WorksMains Pressure On/Off OperationAll 109 and 147 Hi/Lo Models Burner Ignition147 On/Off Models Not Enough HOT Water or no HOT Water Save a Service CallDiagnostic Features of Electronic Thermostat Water Heater not OperatingExpansion Control Valve Running Burner will not LightPressure Relief Valve Running High GAS BillsPressure Relief Valve ServiceRegular Care Expansion Control ValveInspection of Equipment InstallationIndoor Installation Water Heater LocationCombustion / Ventilation AIR Clearances Indoor InstallationsOutdoor Installation Safe TrayInstallation Cold Water Supply High Wind ConditionsTank Water Supply Hood Conversion HOT Water Delivery Water Heating ApplicationsReducing Heat Losses Water Heating Applications Indoor Conversions109 Dimensions and Technical Data147 Models GAS Inlet Connections PlumbingWater Inlet and Outlet Pipe SizesRelief Valve Pressure Rating Model Pump Branch Size Minimum Manifold HeaderPump Selection Relief Valve DrainMechanical Heating Typical Mechanical Heating InstallationTypical Water Heating Installation Water Heating109 147 On/Off Thermostat SettingConnections Electrical Intermittent Pump OperationControl Panel Access Wiring a Power Flued System to the Water HeaterBuilding Management System BMS Wiring Diagram 109 ON/OFF Models Wiring Diagram 109 HI/LO Models Wiring Diagram 147 ON/OFF Models Wiring Diagram 147 HI/LO Models Multi Pump Option Mechanical Heating Systems GAS Control Location of ControlsThermostat Rating LabelDuring First Firing of the Water Heater Safety PrecautionsWhen Handling After HandlingPRE-START Checks CommissioningOperational Checks To Reset the Water Heater Operating the Water HeaterGAS Pressure Adjustment 109 On/Off Models Burner Pressure AdjustmentGAS Inlet Pressure 109 Hi/Lo Models 147 Hi/Lo Models147 On/Off models AKO Thermostat Set Point Adjustment Temperature ControlThermostat Adjustment Differential Adjustment147 Hi/Low Models CTX Thermostat Set Point Adjustment HIGH-LIMIT Thermostat Adustment Water Heating Applications 90C maximumSix Monthly Service Procedure Service ProceduresAnnual Service Procedure Saturation Index Water SuppliesChange of Water Supply Water Quality Charts Warranty Warranty ExclusionsRaypak Water Heater Warranty Australia only 131 031 Australia96109147B

B0109, B0147 specifications

Raypak is a well-established name in the world of heating technology, particularly recognized for its efficient and reliable pool and spa heaters. Among their range, the Raypak B0147 and B0109 models stand out for their performance and advanced features designed to enhance user experience.

Both the Raypak B0147 and B0109 models prioritize efficiency, making them ideal choices for residential or commercial swimming pools. They are engineered to deliver reliable heating, ensuring that water maintains a comfortable temperature no matter the season. One of the standout features is their compact design, which allows for easy installation in various settings without requiring extensive modifications to existing infrastructure.

A key characteristic of the Raypak B0147 is its digital control system. This advanced technology allows users to set precise temperatures and monitor heater performance. The intuitive interface makes it user-friendly, facilitating adjustments on-the-fly. The B0109 model, meanwhile, offers robust heating capabilities, featuring a high-output design that can rapidly elevate water temperatures, perfect for pools with significant heat loss.

Both models utilize a copper-fin-tube heat exchanger, which enhances heat transfer efficiency and extends the lifespan of the heater. This design not only improves thermal efficiency but also ensures that users experience lower energy bills over time. They also come equipped with a dependable ignition system, featuring an automatic spark ignition that eliminates the need for pilot lights, leading to improved safety and reliability.

Durability is another hallmark of the Raypak line. Both models are constructed with materials designed to withstand harsh weather conditions and exposure to pool chemicals, ensuring longevity. The corrosion-resistant housings prevent degradation, maintaining the heater's performance over time.

In summary, the Raypak B0147 and B0109 models deliver outstanding heating performance through efficient technology and durable construction. Their user-friendly controls, compact design, and energy-efficient heat exchangers make them excellent choices for pool owners looking to optimize their heating solutions. With Raypak, users can enjoy comfortable water temperatures year-round, backed by reliable technology and impressive efficiency.
Top Page Image Contents