Optima Company 45 - 3 manual Lighting Instructions on Rating Plate

Page 32

Optima 45 - 3

32

LIGHTING INSTRUCTIONS ON RATING PLATE

LIGHTING INSTRUCTIONS

1.STOP! Read the safety information above on this label.

2.Set the remote switch to “OFF”. Set the thermostat to the lowest setting. (Only if your appliance is equipped with these devices.)

3.Turn off all electric power to the appliance.

4.Open lower louvers or access door.

3.Press slightly and turn the control knob clockwise 3 to the “OFF” position.

4.Wait 5 minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! and follow instruction “B” above.

5.Find pilot. It is located between the logs near the center behind the burner.

6.Press slightly and turn control knob counterclockwise 4 to “PILOT”. Depress knob and light pilot by repeatedly pressing the sparker. Once flame is established, hold knob

depressed for approximately 30 seconds. Release knob. If pilot should go out, repeat steps 3 to 5.

•If the knob does not pop up when released, stop and immediately call your service technician or gas supplier.

•If the pilot will not stay lit after serveral tries, turn the gas control knob to “OFF” and call your service technician or gas supplier.

7.If the appliance has a manual valve, turn gas control knob counterclockwise 4 to the desired heat setting from “LO” to “HI”. If the appliance has an automatic valve, turn gas control knob counterclockwise 4 to “ON” and set the flame adjustment knob to the desired heat setting from “LO” to “HI”.

8.Set the remote switch to “ON”. Set the thermostat to the desired setting. (Only if your appliance is equipped with these devices.)

9.Turn on all electric power to the appliance.

10.Close louver or access door.

TO TURN OFF GAS TO APPLIANCE

303-0001

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Optima 45 Page Introduction Table of Contents Safety Optima 45Installation Codes SpecificationsHigh Altitude Installation Appliance CertificationGAS Connections Natural Gas Pressure SettingsPropane Pressure Settings Appliance Dimensions Appliance DescriptionDimensions and Clearances Alcove InstallationLocating GAS Heater Vent Termination LocationsTermination Locations Approved Vent Components Venting ConnectionVenting Restrictor Placement Simpson Dura-Vent Archgard SystemVenting Chart 71 MVenting Vertical Termination Using Simpson DURA-VENT Pipe Feet Venting Horizontally Using Archgard TVK-FSU Vent KIT Termination Framing Spring SpacersVenting below Grade Using Flexible Direct Vent Systems Installation Procedures for Archgard Snorkel KIT SNK-24Flat Wall Installation Corner InstallationsSet the Optima 45-3 in its desired location Optima 45 Below Grade Above Grade LOG Placement Piece LOG SET Shown below Burner Pan & Pin LocationsLocate Log # 12 and place it on the burner pins as shown Locate Log #142 and place it on Log #12 as shown LOG #83 Front View Ceramic Brick PanelsOptional Wall Switch or Thermostat Valve Connection for Millivolt ValveFinal Installation Check Initial OperationFirst Fire Lighting Instructions CautionLighting Instructions on Rating Plate Lighting InstructionsGlass Door Removal If Your Glass BreaksRemoving the Glass Door Replacing the Glass DoorTroubleshooting Troubleshooting Maintenance Cleaning the Appliance RegularlyServicing Under Warranty Adjusting Primary AIRAdjusting Primary AIR Changing Main Burner Orifice Checking and Adjusting Pilot Convertible Pilot Orifice Checking Inlet and Outlet GAS PressureCanadian Electrical code, CSA C22.1 Wiring DiagramReplacing Convection Blower Valve Tray Assembly Item # Item Description Qty UnitParts List Ceramic Logs and Burner Pan Burner Pan & Pin Locations Item # Item Description Qty UnitCeramic Brick Replacement Parts List Archgard OptimaQty Unit Archgard Limited Warranty Frequently Asked Questions Optima 45 Page Warranty Registration Beatty Drive MISSION, B.C. Canada

45 - 3 specifications

Optima Company 45 - 3 is an innovative product in the realm of advanced manufacturing and technology. This state-of-the-art machine has gained attention for its unique blend of efficiency, precision, and adaptability, making it a preferred choice for various industries, including automotive, aerospace, and electronics.

One of the standout features of the Optima Company 45 - 3 is its versatility. The machine is designed to handle a wide range of materials, from metals to plastics, enabling manufacturers to utilize it across multiple projects without extensive modifications. This flexibility not only saves time and resources but also streamlines the production process, allowing businesses to respond quickly to market demands.

Equipped with cutting-edge technologies, the Optima Company 45 - 3 boasts advanced automation capabilities. This includes integrated robotics and smart sensors that facilitate real-time monitoring and adjustments during operation. These features help ensure optimal performance levels, reducing the risk of errors and minimizing downtime, ultimately translating to a higher return on investment for users.

In terms of precision, the Optima Company 45 - 3 employs advanced CNC (Computer Numerical Control) technology. This allows for intricate designs and specifications to be followed with remarkable accuracy. The millimeter-perfect cuts and finishes not only enhance the quality of the final product but also reduce the need for additional post-processing, which can be time-consuming and costly.

Another significant characteristic of the Optima Company 45 - 3 is its energy efficiency. In a world where sustainability is paramount, the machine is designed to operate using less power without compromising on performance. This environmentally friendly approach not only lowers operational costs but also aligns with green initiatives that many companies are striving to achieve.

Moreover, the user interface of the Optima Company 45 - 3 has been simplified to ensure ease of operation. The intuitive controls allow even novice operators to manage complex tasks with minimal training, thereby reducing the learning curve associated with traditional manufacturing equipment.

In conclusion, the Optima Company 45 - 3 sets a new benchmark in the manufacturing landscape. Its combination of versatility, precision, automation, energy efficiency, and user-friendliness makes it an invaluable asset for companies looking to enhance their production capabilities and stay competitive in a fast-evolving market.
Top Page Image Contents