Optima Company 45 - 3 GAS Connections, Natural Gas Pressure Settings, Propane Pressure Settings

Page 7

Optima 45 - 3

7

GAS CONNECTIONS

Before connecting the appliance to the gas supply line, double check that the appliance you have purchased is designed for the gas type you are using. The gas type markings are located on the certification label and also on the appliance’s gas valve.

Adequate clearance for proper installation and checking of the gas connections must be provided. All gas connections must be checked for gas leaks.

Have your gas supplier or a qualified gas fitter run a gas supply line into the heater.

The line must be properly sized and fitted according to the installation codes. Immediately upstream of the supply connection, the fitter shall provide an accessible manual shut-off valve and a ⅛” (3 mm) NPT plugged tapping accessible for connection to a test gauge. When connecting the supply line to the gas valve, the installer shall brace the gas valve to ensure that gas valve is not moved from its bracket. If the valve is not braced when the supply line is connected, the valve may be moved and cause a “break” in the main burner supply line. Such damage is not covered by the manufacturer’s warranty.

CAUTION: The appliance and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure-testing of that system at test pressures in excess of ½ psig (3.5 kPa). The appliance must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure-testing of the gas supply piping system at test pressures equal to or less than ½ psig (3.5 kPa). Failure to do so will damage the appliance’s gas valve. Such damage is not covered by the manufacturer’s warranty.

Natural Gas Pressure Settings:

The inlet supply or line pressure must be a minimum of 4.5” w.c. (1.1 kPa) and a maximum of 8” w.c. (2 kPa). The orifice is a #37 DMS (2.66 mm) drill size.

ELEVATION

INPUT RATING

0-4500 ft (0-1372 M)

28,000

BTU/hr

(8.2 kW)

4500 ft (1372 M) and above

28,000

BTU/hr (8.2 kW) less 4% per 1000 ft. (305 M)

Please contact your local utility company or distributor for the appropriate orifice size you require.

Propane Pressure Settings:

The inlet supply or line pressure must be a minimum of 11” w.c. (2.8 kPa) and a maximum of 14” w.c. (3.5 kPa). The orifice is a #52 DMS (1.60 mm) drill size.

ELEVATION

INPUT RATING

0-4500 ft. (0-1372 M)

28,000 BTU/hr

(8.8 kW)

4500 ft. (1372 M) and above.

28,000 BTU/hr (8.8 kW) less 4% per 1000 ft. (305 M)

Please contact your local utility company or distributor for the appropriate orifice size you require

NOTE: THE INPUT RATING SHOULD ALWAYS BE CHECKED WHEN FIRST RUNNING THIS APPLIANCE. To do this, reduce the background flow rate, time the meter, light the fireplace and take another reading after 15 minutes of operation. Check with your gas supplier for the gas BTU content at your elevation. Input is the rate of flow multiplied by the heating value of the gas (cubic feet/hour x BTU per cubic feet). Adjust the manifold pressure so that the unit does not operate above the rated input.

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Optima 45 Page Introduction Table of Contents Optima 45 SafetyAppliance Certification Installation CodesSpecifications High Altitude InstallationPropane Pressure Settings Natural Gas Pressure SettingsGAS Connections Appliance Description Appliance DimensionsAlcove Installation Dimensions and ClearancesVent Termination Locations Locating GAS HeaterTermination Locations Venting Connection Approved Vent ComponentsSimpson Dura-Vent Archgard System Venting Restrictor Placement71 M Venting ChartVenting Vertical Termination Using Simpson DURA-VENT Pipe Feet Termination Framing Spring Spacers Venting Horizontally Using Archgard TVK-FSU Vent KITInstallation Procedures for Archgard Snorkel KIT SNK-24 Venting below Grade Using Flexible Direct Vent SystemsCorner Installations Flat Wall InstallationSet the Optima 45-3 in its desired location Optima 45 Below Grade Above Grade LOG Placement Burner Pan & Pin Locations Piece LOG SET Shown belowLocate Log # 12 and place it on the burner pins as shown Locate Log #142 and place it on Log #12 as shown LOG #83 Ceramic Brick Panels Front ViewValve Connection for Millivolt Valve Optional Wall Switch or ThermostatInitial Operation Final Installation CheckLighting Instructions Caution First FireLighting Instructions Lighting Instructions on Rating PlateReplacing the Glass Door Glass Door RemovalIf Your Glass Breaks Removing the Glass DoorTroubleshooting Troubleshooting Regularly Maintenance Cleaning the ApplianceAdjusting Primary AIR Servicing Under WarrantyAdjusting Primary AIR Changing Main Burner Orifice Checking Inlet and Outlet GAS Pressure Checking and Adjusting Pilot Convertible Pilot OrificeReplacing Convection Blower Wiring DiagramCanadian Electrical code, CSA C22.1 Item # Item Description Qty Unit Valve Tray AssemblyBurner Pan & Pin Locations Item # Item Description Qty Unit Parts List Ceramic Logs and Burner PanQty Unit Replacement Parts List Archgard OptimaCeramic Brick Archgard Limited Warranty Frequently Asked Questions Optima 45 Page Warranty Registration Beatty Drive MISSION, B.C. Canada

45 - 3 specifications

Optima Company 45 - 3 is an innovative product in the realm of advanced manufacturing and technology. This state-of-the-art machine has gained attention for its unique blend of efficiency, precision, and adaptability, making it a preferred choice for various industries, including automotive, aerospace, and electronics.

One of the standout features of the Optima Company 45 - 3 is its versatility. The machine is designed to handle a wide range of materials, from metals to plastics, enabling manufacturers to utilize it across multiple projects without extensive modifications. This flexibility not only saves time and resources but also streamlines the production process, allowing businesses to respond quickly to market demands.

Equipped with cutting-edge technologies, the Optima Company 45 - 3 boasts advanced automation capabilities. This includes integrated robotics and smart sensors that facilitate real-time monitoring and adjustments during operation. These features help ensure optimal performance levels, reducing the risk of errors and minimizing downtime, ultimately translating to a higher return on investment for users.

In terms of precision, the Optima Company 45 - 3 employs advanced CNC (Computer Numerical Control) technology. This allows for intricate designs and specifications to be followed with remarkable accuracy. The millimeter-perfect cuts and finishes not only enhance the quality of the final product but also reduce the need for additional post-processing, which can be time-consuming and costly.

Another significant characteristic of the Optima Company 45 - 3 is its energy efficiency. In a world where sustainability is paramount, the machine is designed to operate using less power without compromising on performance. This environmentally friendly approach not only lowers operational costs but also aligns with green initiatives that many companies are striving to achieve.

Moreover, the user interface of the Optima Company 45 - 3 has been simplified to ensure ease of operation. The intuitive controls allow even novice operators to manage complex tasks with minimal training, thereby reducing the learning curve associated with traditional manufacturing equipment.

In conclusion, the Optima Company 45 - 3 sets a new benchmark in the manufacturing landscape. Its combination of versatility, precision, automation, energy efficiency, and user-friendliness makes it an invaluable asset for companies looking to enhance their production capabilities and stay competitive in a fast-evolving market.
Top Page Image Contents