Optima Company 45 - 3 manual Glass Door Removal, If Your Glass Breaks, Removing the Glass Door

Page 33

Optima 45 - 3

33

 

 

 

 

 

 

 

GLASS DOOR REMOVAL

 

 

 

 

 

 

 

 

 

 

 

WARNING:

•Do not attempt to remove the glass panel assemblies when the appliance is hot.

•Do not strike or abuse glass panel (s).

•Do not operate with glass panel (s) broken or cracked.

•Broken or cracked glass panel assemblies must be replaced only with those supplied by Archgard Industries.

•Do not use substitute materials or assemblies.

•Replacement of the glass should be carried out by a licensed or qualified service person.

WARNING: Do not attempt to remove the glass door when the appliance is hot.

Removing the Glass Door

1.Open both side cover doors.

2.Unlatch the right hand door catches.

3.Swing the door open.

4.Lift the door clear of the bottom hinge and drop out of the top hinge.

Replacing the Glass Door

Reverse the above procedure.

IF YOUR GLASS BREAKS

To open the door release the two securing catches

In the event that your glass cracks or breaks, Archgard recommends that a new door assembly be ordered to replace the original door.

•Remove door as per the instructions above.

•Replace with new door assemblies.

NOTE: the NEW door will omit some odor when the appliance is re-lit and the odor will dissipate after the gasket material within the door has cured.

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Optima 45 Page Introduction Table of Contents Optima 45 SafetySpecifications Installation CodesHigh Altitude Installation Appliance CertificationNatural Gas Pressure Settings Propane Pressure SettingsGAS Connections Appliance Description Appliance DimensionsAlcove Installation Dimensions and ClearancesVent Termination Locations Locating GAS HeaterTermination Locations Venting Connection Approved Vent ComponentsSimpson Dura-Vent Archgard System Venting Restrictor Placement71 M Venting ChartVenting Vertical Termination Using Simpson DURA-VENT Pipe Feet Termination Framing Spring Spacers Venting Horizontally Using Archgard TVK-FSU Vent KITInstallation Procedures for Archgard Snorkel KIT SNK-24 Venting below Grade Using Flexible Direct Vent SystemsCorner Installations Flat Wall InstallationSet the Optima 45-3 in its desired location Optima 45 Below Grade Above Grade LOG Placement Burner Pan & Pin Locations Piece LOG SET Shown belowLocate Log # 12 and place it on the burner pins as shown Locate Log #142 and place it on Log #12 as shown LOG #83 Ceramic Brick Panels Front ViewValve Connection for Millivolt Valve Optional Wall Switch or ThermostatInitial Operation Final Installation CheckLighting Instructions Caution First FireLighting Instructions Lighting Instructions on Rating PlateIf Your Glass Breaks Glass Door RemovalRemoving the Glass Door Replacing the Glass DoorTroubleshooting Troubleshooting Regularly Maintenance Cleaning the ApplianceAdjusting Primary AIR Servicing Under WarrantyAdjusting Primary AIR Changing Main Burner Orifice Checking Inlet and Outlet GAS Pressure Checking and Adjusting Pilot Convertible Pilot OrificeWiring Diagram Replacing Convection BlowerCanadian Electrical code, CSA C22.1 Item # Item Description Qty Unit Valve Tray AssemblyBurner Pan & Pin Locations Item # Item Description Qty Unit Parts List Ceramic Logs and Burner PanReplacement Parts List Archgard Optima Qty UnitCeramic Brick Archgard Limited Warranty Frequently Asked Questions Optima 45 Page Warranty Registration Beatty Drive MISSION, B.C. Canada

45 - 3 specifications

Optima Company 45 - 3 is an innovative product in the realm of advanced manufacturing and technology. This state-of-the-art machine has gained attention for its unique blend of efficiency, precision, and adaptability, making it a preferred choice for various industries, including automotive, aerospace, and electronics.

One of the standout features of the Optima Company 45 - 3 is its versatility. The machine is designed to handle a wide range of materials, from metals to plastics, enabling manufacturers to utilize it across multiple projects without extensive modifications. This flexibility not only saves time and resources but also streamlines the production process, allowing businesses to respond quickly to market demands.

Equipped with cutting-edge technologies, the Optima Company 45 - 3 boasts advanced automation capabilities. This includes integrated robotics and smart sensors that facilitate real-time monitoring and adjustments during operation. These features help ensure optimal performance levels, reducing the risk of errors and minimizing downtime, ultimately translating to a higher return on investment for users.

In terms of precision, the Optima Company 45 - 3 employs advanced CNC (Computer Numerical Control) technology. This allows for intricate designs and specifications to be followed with remarkable accuracy. The millimeter-perfect cuts and finishes not only enhance the quality of the final product but also reduce the need for additional post-processing, which can be time-consuming and costly.

Another significant characteristic of the Optima Company 45 - 3 is its energy efficiency. In a world where sustainability is paramount, the machine is designed to operate using less power without compromising on performance. This environmentally friendly approach not only lowers operational costs but also aligns with green initiatives that many companies are striving to achieve.

Moreover, the user interface of the Optima Company 45 - 3 has been simplified to ensure ease of operation. The intuitive controls allow even novice operators to manage complex tasks with minimal training, thereby reducing the learning curve associated with traditional manufacturing equipment.

In conclusion, the Optima Company 45 - 3 sets a new benchmark in the manufacturing landscape. Its combination of versatility, precision, automation, energy efficiency, and user-friendliness makes it an invaluable asset for companies looking to enhance their production capabilities and stay competitive in a fast-evolving market.
Top Page Image Contents