GE 5100 installation instructions Central Desk Control, Do not use a common buss in the CDC wiring

Page 17

Central Desk Control

 

CDC

 

 

 

 

 

 

 

 

 

 

Load shedding

 

 

 

 

9

 

12

 

ON

 

 

 

 

 

 

 

 

 

ON

 

 

OFF

 

 

 

 

 

 

 

 

 

OFF

 

 

Auxiliary Controls

The Zoneline can be connected to a switch at the front desk that allows you to turn the unit on or off without going to each unit.

When the front desk switch is open the Zoneline is on. Turn the switch to closed to turn it off.

For load shedding, the CDC auxiliary switch 9 must be in the OFF (down) position and auxiliary switch 12 must be in the ON (up) position. This provides fan operation while the compressor or heater is turned off.

NOTE:

The Freeze Sentinel remains active to help protect against low temperature damage even though the unit may be off at the central control location.

IMPORTANT:

After the wire connections are completed, replace the metal cover to prevent damage to the unit or personal injury.

Metal cover over recessed connection space

Recommended wire size for Central Desk Control installation

Wire Size

Maximum

Allowable

# AWG

Length

 

#24

400 ft.

#22

600 ft.

#20

900 ft.

#18

1500 ft.

#16

2000 ft.

Follow the recommended wire sizing in the table. Two wires must be used from each CDC switch to each individual unit.

DO NOT use a common buss in the CDC wiring.

Good wiring practices (e.g. twisted pairs, separation from power circuits) must be followed to minimize induced voltages which may harm the control system.

A 24-volt transformer is contained within the unit and no external voltage should be applied to the unit through the CDC terminals. These terminals may also be used as an interface for other systems used to control the unit, such as infrared detectors, key-activated systems, etc.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Zoneline Write down the model and serial Before using your Zoneline800.626.2000 Replacing an existing unit? Read ALL Safety Information Before UsingControls on your Zoneline Mode ControlVentilation Control About Your Heat Pump Other Zoneline featuresFreeze Sentinel Fan SwitchOutdoor Coils Care & CleaningBase Pan Room Cabinet and CaseAir Filters Use the correct wall case Read carefullyUse the correct outdoor grille Replacing a ducted chassis Replacing 230/208 volt unitsZoneline Components Important electrical safety-read carefullyImportant Notes Volt Electrical Supply How to Connect230/208 Volt Electrical Supply Insulated Wall Case Power Connection ChartInstall the Wall Case and Exterior Grille Replace the Room Cabinet Install the Unit into the Wall CaseElectric Heat Option Low Voltage Connectors & Auxiliary ControlsBoost Heat Option PCS Remote Control Wall ThermostatCentral Desk Control Do not use a common buss in the CDC wiringTemperature Limiting Diagnosis SwitchExplanation Things that are normalNoise Zoneline Does Not Cool or Heat as it Should Before you call for serviceZoneline Doesn’t Start What to DoBurning Odor at Start of Heating Operation Call SVC Indicator LightHeating Operation Air is Not Always Cool or Hot During OperationPage On-Site Repair Service Further ServiceParts and Accessories We’ll be thereWhat is Not Covered What is Covered

5100 specifications

The GE 5100 is a state-of-the-art gas turbine engine developed by General Electric, designed to offer unparalleled efficiency and reliability for power generation. This advanced engine has been engineered with a focus on innovative technology and cutting-edge materials, making it a favorable choice for utility companies and independent power producers around the globe.

One of the main features of the GE 5100 is its remarkable efficiency. With a simple cycle efficiency surpassing traditional gas turbines, the GE 5100 ensures that utility providers can generate more electricity from the same amount of fuel. This is crucial in today’s energy landscape, where operational costs and environmental concerns are top priorities.

The GE 5100 employs a modular design that facilitates maintenance and reduces downtime. The engine consists of easy-to-replace modules, enabling rapid service without extensive disassembly. As a result, power plants using the GE 5100 experience enhanced availability and lower operational costs.

In terms of technology, the GE 5100 utilizes advanced aerodynamics, which optimizes airflow through the turbine and enhances its overall performance. The blade design has been refined using sophisticated computational fluid dynamics (CFD) simulations, which allow engineers to predict performance accurately while minimizing drag and maximizing thrust.

Another notable characteristic of the GE 5100 is its durability. The engine is constructed using high-performance materials that can withstand extreme temperatures and pressures. This robustness not only extends the life of the engine but also ensures reliability even in the most demanding operational environments.

Furthermore, the GE 5100 incorporates an advanced control system that enables operators to monitor performance in real-time, adjusting parameters for optimal efficiency. This level of precision helps to optimize fuel consumption while adhering to emissions regulations, making it a greener option in power generation.

In summary, the GE 5100 gas turbine engine stands out for its efficiency, modular design, advanced aerodynamics, durability, and sophisticated control systems. These features make it a compelling choice for energy providers aiming to improve their performance while remaining environmentally responsible. With the ever-evolving landscape of energy demands, the GE 5100 represents a significant leap forward in gas turbine technology, providing reliable and efficient power generation solutions globally.
Top Page Image Contents