Heatiator GDST3831I owner manual 330 mm, 34 mm, 14-1/16, 357 mm, 192 mm, Termination Cap

Page 57

B. Vent Components Diagrams (continued)

	14 in.					13 in.
	356 mm					330 mm
10-9/16 in.					13 in.	1-5/16 in.
10-9/16 in.					13 in.	34 mm
269 mm					330 mm
SLP-CCS-BK					SLP-DCF-BK
SLP-CCS-BK					Ceiling Firestop
Cathedral Ceiling					Ceiling Firestop
Cathedral Ceiling						Black
Support Box-Black						Black
Support Box-Black
14-1/16 in.			6-11/16 in.			7-1/4 in.
357 mm			169 mm		1 in.	(184 mm)
		10-3/4 in.			(25 mm)
		10-3/4 in.
14 in.	7-1/2 in.	273 mm
14 in.	7-1/2 in.
356 mm	192 mm
	SLP-FLEX-TRAP				14 in.
	Horizontal				(356 mm)
	Termination Kit
					3/8 in. (10 mm)
	10-11/16 in.				1 in. (25 mm)
	271mm					7-3/4 to 10-3/8 in.
						7-3/4 to 10-3/8 in.
						(197 to 264 mm)
						DVP-FBHT
						Horizontal
28-1/2 in.						Termination Cap
28-1/2 in.
724 mm
13-1/2 in.					DVP-FBHT
343 mm					DVP-FBHT	DVP-FBHT
			SLP90	SL-2DVP		DVP-FBHT
				SL-2DVP
SLK-SNKD
SLK-SNKD
Snorkel
Termination Cap
Figure 16.4 SLP Series Vent Components				ASSEMBLY
	Heatilator •		GDST3831I	• 2127-900 Rev. K • 7/12		57

Image 57

Contents Models What to do if you smell gasHOT Surfaces Homeowner Reference Information CongratulationsUser Guide Table of ContentsTroubleshooting Appliance SetupElectrical Information FinishingLimited Lifetime Warranty Limited Lifetime WarrantyWarranty Conditions Listing and Code Approvals Requirements for the Commonwealth of Massachusetts Installation of Carbon Monoxide DetectorsGas Fireplace Safety Operating Instructions User GuideYour Fireplace Remote Controls, Wall Controls and Wall Switches Fixed Glass AssemblyFan Kit optional Clear SpaceFinal inspection by Lighting Instructions IPIWhat to do if YOU Smell GAS GAS ValveFrequently Asked Questions Issue SolutionsAfter Fireplace is Lit Maintenance Tasks-Homeowner Maintenance and ServiceGlass Cleaning Remote ControlGasket Seal and Glass Assembly Inspection Maintenance Tasks-Qualiﬁed Service TechnicianVenting LogsIPI Pilot Flame Patterns Burner Ignition and OperationTypical Appliance System Getting StartedDesign and Installation Considerations Tools and Supplies NeededInspect Appliance and Components Selecting Appliance Location Framing and ClearancesMinimum Framing Dimensions Constructing the Appliance ChaseClearances TOP View Fireplace Opening Mantel and Wall ProjectionsVent Termination Minimum Clearances Termination LocationsInches U.S.A Covered Alcove ApplicationsTo Install the Heat Shield Install Support BracketsContinue Adding Vent Components CorrectApproved Pipe Vent Information and DiagramsVent Table Key Use of ElbowsUse of Flex Vent Vent Diagrams Top Vent Horizontal Termination One ElbowV1 Minimum H1 Maximum V1 Minimum H1 + H2 Maximum Top Vent Horizontal Termination Two ElbowsV1 Minimum H1 + H2 Maximum V1 + V2 Min Top Vent Horizontal Termination Three ElbowsExhaust restrictor Instructions V1 Minimum Maximum V1 + V2 Min Pipe Clearances to Combustibles Vent Clearances and FramingWall Penetration Framing Combustible Wall PenetrationPipe SLP Install the Ceiling FirestopInstall Attic Insulation Shield Flat Ceiling InstallationVaulted Ceiling Installation Securing and Leveling the Appliance Appliance PreparationAssemble Vent Sections Installing Vent PipeSecuring the Vent Sections Assemble Slip SectionsDisassemble Vent Sections Installing Decorative Ceiling ComponentsAssemble and Install Storm Collar Installing Metal Roof FlashingInstalling Vertical Termination Cap Installing Decorative Wall ComponentsHeat Shield Requirements for Horizontal Termination 17 Venting through the wall Install Horizontal Termination CapFuel Conversion Gas InformationGas Pressure Gas ConnectionOptional Accessories Requirements Wiring RequirementsElectrical Information Code CSA C22.1Intelliﬁre Ignition Wiring Diagram with Remote Receiver Wall Switch Installation for Fan Optional Junction Box InstallationFinishing Sides using a 300 F minimum sealant. Refer toFacing Material Metal front faces may be covered with non-combustibleSplatter Guard To install the Splatter GuardTo Remove the Splatter Guard To Close the Lower Access PanelAppliance Setup Models ST-550T-IPI. GDST3831I Install the Log AssemblyNotch Install Trim Kits and Surrounds Air Shutter SettingAir Shutter Settings Troubleshooting Symptom Possible Cause Corrective ActionIntelliﬁre Ignition System Speciﬁcations. Polish ﬂame sensing rod with ﬁne steel wool Appliance Dimension Diagram Electrical Access Left View Front View GAS Line Right ViewReference Materials  B. Vent Components Diagrams SLP-TVHW Vent Components Diagrams34 mm 330 mm14-1/16 357 mmDVP-TB1 Horizontal Termination CAP SLP-HRC-SS SLP-HRC-ZC-SS Horizontal Termination CAPSLP-LPC Optional Wire HarnessLog Set Assembly Service PartsStocked At DepotStocked #9 Valve AssemblyService Parts List Do not Discard this Manual Contact Information