Panasonic SC-HTB8 Drive a screw into the wall, Fit the main unit securely onto the screws, Do Not

Page 14

Drive a screw into the wall.

Drive a screw into the wall.

≥Use the measurements indicated below to identify the screwing positions on the wall.

≥Leave at least 20 mm (25/32q) of space above of the main unit to allow enough space for fitting the main unit.

≥Leave at least 10 mm (13/32q) of space on both sides of the main unit. Without sufficient space, it is not possible to mount the main unit successfully.

≥Be sure to use a level to insure that both mounting holes are level to each other.

	
	
	
	
	

Front view (semi-transparent image)

BAt least 30 mm (1 3/16q) C ‰4.0 mm (5/32q)

D ‰7.5 mm to ‰9.4 mm (9/32q to 3/8q) E Wall or pillar

F 7.5 mm to 8.5 mm (7/32q to 11/32q)















G

320 mm (12 19/32q)

H

215 mm (8 15/32q)

I 215 mm (8 15/32q)

J

15 mm (19/32q)

K

115 mm (4 17/32q)

L Wall mounting hole

Fit the main unit securely onto the screw(s).

DO	DO NOT
≥ Move the speaker so	≥ In this position, the
that the screw is in this	speaker will likely fall if
position.	moved to the left or right.

Secure the cord to the wall.

≥Make sure that the slack of the cord is minimal.





MScrew eye N Cord

14 VQT5J41

Image 14

Contents Model No. SC-HTB8 Included Installation InstructionsVQT5J41 DO NOT INGEST BATTERY CHEMICAL BURN HAZARD AC power supply cordButton-type battery Lithium battery UnitPrecautions PlacementThe following mark and symbols are located on bottom of the unit FCC NoteStep 2 Placement Limited WarrantyIMPORTANT SAFETY INSTRUCTIONS Using this systemPrecautions Before use Getting started Operations Reference Accessory∏ 1 Remote control with a battery N2QAYC000102 Supplied itemsThis system Front 1 Standby/on switch Í/IControl reference guide This system RearTo replace a button-type battery Remote controlBefore using for the first time ∫ About remote control signal sensorStep 1 Connections AC power supply cord connectionD AC power supply cord Connection with the TV APress and hold until the “ ” indicator flashes quickly Bluetooth connectionBluetooth pairing Press to select “ ” Select “SC-HTB8” from the Bluetooth menu of your deviceWireless interference Step 2 PlacementSafety Precautions Professional installation is requiredWhen attaching the main unit to a wall Selecting the placement methodWhen placing the main unit on a rack or on a table When placing the main unit in front of the TVSlide the MULTI ANGLE switch to “RACK/TABLE TOP” When placing the main unit on a rack or on a tableAdditionally required accessories commercially available Attach the cord to the main unitWhen attaching the main unit to a wall Slide the MULTI ANGLE switch to “WALL MOUNT”Secure the cord to the wall Drive a screw into the wallFit the main unit securely onto the screws Front view semi-transparent image∫ When “ ” is selected as the source Using this systemTo adjust the volume of this system When “BD/DVD” is selected as the sourceOthers Remote control code Auto Power DownBluetooth Stand-by To turn off the volume limitationPairing cannot be done TroubleshootingBluetooth To return to the factory defaultsSound The volume is lowered when the main unit is turned onThere is no audio The power of the main unit turns off automatically No soundUnit care About BluetoothClean this system with a soft, dry cloth LicenseDescription The indicator blinks for 20 sec Indicator illuminationIndicator The indicator blinks for 20 secTotal RMS Stereo mode power SpecificationsBluetooth SECTION FTC output power Stereo mode Front ch both ch drivenLimited Warranty Limits And Exclusions Panasonic Products Limited WarrantyLimited Warranty Coverage For USA Only Online Repair RequestReference Information on Disposal in other Countries outside the European Union If you see this symbolVQT5J41 F0314KE0 Panasonic Corporation of North America