Multi Tech Equipment MLT20DCA6 operation manual Circuit Breakers Turn the lamps on and off

Page 15

components

21

21

 

20

23

REAR VIEW

22

FRONT VIEW

Figure 3. Major Components (Front/Rear)

13.Tongue Jackstand — Use this jackstand to support the tongue when attaching the light tower to a towing vehicle.

14.Safety Chain — Always attach safety chain to the towing vehicle. Never tow the light tower with the safety chain unattached.

15.Ball Hitch Coupler — Attach this coupler to the towing vehicle. Use only the specified ball diameter as indicated on your coupler. Use of any other ball diameter will create an extremely dangerous condition which can result in separation of the coupler and ball or ball failure.

16.Vertical Mast Winch — Use this winch to raise the mast to the vertical position.

17.Mast Lock/Release Pin — Pull this pin to start placing the tower mast in the vertical position. When tower mast has reached full vertical position, insert pin to keep mast from falling.

18.Tie-Down Points — Used to tie down light tower with strap or chains to allow even application of force to the front and rear of the equipment during transport.

19.Circuit Breakers — Turn the lamps on and off.

20.License Light — This light illuminates the license plate. Whenever towing of the light tower is required, make sure this light is operational.

21.Brake Lights — Before towing the light tower, make sure that these lights are operational and are working correctly. Never tow the light tower if these lights are inoperative.

22.Engine Exhaust Pipe — Directs engine exhaust to the rear of the light tower. NEVER block this exhaust pipe with obstructions. ALWAYS place the generator in an area free of obstructions.

23.Tires — This light tower uses ST205/75D15 LR-C size tire. Replace with only recommended tire size. Never tow light tower with bad or worn tires.

MLT20 SERIES LIGHT TOWER • operation manual — rev. #0 (01/18/13) — page 15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Models Proposition 65 warning Nhtsa Reporting Safety DefectsSpecifications are subject to change without notice Table of ContentsAddresses practices not related to personal injury Safety InformationSaFeTY Messages SaFeTY sYMBOLsGeneRaL saFeTY LaMp saFeTY LIgHT TOWeR saFeTYTOWIng saFeTY Loading and Tie-Down on Flatbed Truck TRanspORTIng saFeTY„ neveR operate light tower ELeCTRICaL saFeTYMLT20 Series Specifications Light Tower SpecificationsGenerator/Engine Specifications Length Mast Stowed Position Length Mast Deployed Position DimensionsDimensions Reference Letter Description DimensionMetal Halide Lamps General informationMajor Components Control Panel Side ComponentsMajor Components Front/Rear Circuit Breakers Turn the lamps on and offCheck all fastening nuts and bolts for tightness Read all safety instructions at the beginning of manualInspection Before startingFemale and Male Connector Contact between the two connectorsOutriggers and Support Stands OperationStarting the Engine Mast operationRaising the Mast Rotating the Mast Raising the MastLowering the Mast Stowing the Mast to Horizontal PositionVoltage Regulator Knob and AC Voltmeter Servicing the Mast Raise/Lower Cable System MaintenanceGenerator/ENGINE Maintenance Check Cable WearLower the mast to the horizontal resting position Servicing the Mast Extension Cable SystemHydraulic Brakes Maintenance TrailersManually Adjusting the Brakes Trailer BrakesHydraulic Brake Troubleshooting Adjustable ChannelLeaf Suspension Wheel Hub AdjustmentSafety guidelines Trailers COMMOn Causes for LOss of TRaILeRTRaILeR TOWIng guIDeLInes COupLIng to THe TOW veHICLe DRIvIng COnDITIOnsInOpeRaBLe BRaKes, LIgHTs or MIRRORs TRaILeR TOWIng TIpsTRaILeR vIn Tag BRaKe COnTROLLeR ELeCTRICaL COnneCTORTOW veHICLe SuspensIOn sYsTeMJaCKsTanD SaFeTY CHaInsTRaILeR LIgHTIng anD BRaKIng COnneCTOR BReaKaWaY sYsTeMLock washer and hitch frame Trailer tongue. Wood or concrete blocks may also be usedCoupling the Trailer to the Tow vehicle Ball Coupler Attaching safety Chain Breakaway Brake systemBreakaway Cable surge Brake system Pintle Coupler and pintle Hook Connecting Trailer LightsUncoupling the Ball Hitch PInTLe Hitch COupLeRCoupling Trailer to Tow vehicle pintle Coupler Figure H. Attaching Safety Chain Pintle HitchTIRe saFeTY Unsafe Tires, Lug nuts or Wheels Determining Load Limit of TrailerBe sure lug nuts are tight before each tow Determining Load Limit of Tow vehicle step StepTIRe FunDaMenTaLs Table a. speed RatingLetter Rating Speed Rating Uniform Tire Quality grading standards uTQgs Tire safety TipsTire Repair Replacing Worn or Damaged TiresLug nut Torque Requirements Table B. Tire Wear TroubleshootingWheel Rims Wheels, Bearings and Lug nutsTable C. Tire Torque Requirements Lights and signalsSymptom Possible Cause Solution Lamp TroubleshootingLamp starts slowly ARC does not strike Defective Lamp? When switch is first Checking voltage and ballast Turned onReplacement minimizes color differences Clean fixtureBallast Removal Lamp Troubleshooting GuideConnections StartingPage Electronic Component Locator mlt20dca Reference MLT20DCA 4-lamp wiring diagram on succeeding pagesElectronic Component Locator mlt20dca6 Wiring Diagram mlt20dca TB1 N Wiring Diagram mlt20dca6 TB1 Z HERE’S HOW to GET Help

MLT20DCA6, MLT20DCA specifications

The Multi Tech Equipment MLT20DCA and MLT20DCA6 stand out in the realm of compact construction machinery, renowned for their versatility and efficiency. These models are designed to meet the demanding needs of various industries, including construction, landscaping, and agricultural operations.

One of the key features of the MLT20DCA series is its powerful and reliable engine. Equipped with a robust diesel engine, these machines deliver optimal performance and fuel efficiency, ensuring that operators can complete tasks quickly and economically. This powertrain is complemented by a highly responsive hydraulic system, which allows for seamless operation of attachments such as buckets, forks, and augers.

The ergonomic design of the MLT20DCA and MLT20DCA6 enhances operator comfort and productivity. The spacious cabin is equipped with intuitive controls and offers excellent visibility, making it easier for operators to navigate tight spaces and perform intricate tasks. The low center of gravity provides stability and balance, which is essential when working on uneven terrain.

Both models feature a compact design, making them ideal for urban environments and confined job sites. Their versatile lifting capabilities allow them to handle a wide range of materials, from heavy loads to delicate items, making them invaluable in various applications. The MLT20DCA6 variant offers additional lifting height and capacity, catering to heavier-duty operations.

Safety is a paramount concern in equipment design, and the MLT20DCA series does not disappoint. These machines are equipped with multiple safety features, including reinforced ROPS (Roll Over Protective Structure), safety interlocks, and improved braking systems. This ensures the well-being of operators and those working in proximity.

In terms of technology, Multi Tech has integrated advanced control systems into both models. This includes automated diagnostics that monitor machine performance and alert users to potential issues before they become significant problems. Connectivity features also allow for remote monitoring, enhancing fleet management capabilities.

In summary, the Multi Tech Equipment MLT20DCA and MLT20DCA6 represent a formidable option for professionals seeking reliable and efficient compact machinery. With their powerhouse engines, user-friendly design, and advanced safety and technology features, these machines are poised to enhance productivity across various applications, ensuring a strong return on investment for operators.
Top Page Image Contents