Multi Tech Equipment MLT20DCA6 operation manual Wheel Hub Adjustment, Leaf Suspension

Page 26

maintenance — TRAILERS

„„After removing the dust cap, cotter pin, spindle nut and spindle washer, remove the hub to inspect the bearings for wear and damage.

„„Replace bearings that have flat spots on rollers, broken roller cages, rust or pitting. Always replace bearings and cups in sets. The inner and outer bearings are to be replaced at the same time.

„„Replace seals that have nicks, tears or wear.

„„Lubricate the bearings with a high quality EP-2 automotive wheel bearing grease.

Wheel Hub Adjustment

Every time the wheel hub is removed and the bearings are reassembled, follow the steps below to check the wheel bearings for free running and adjust.

„„Turn the hub slowly, by hand, while tightening the spindle nut until you can no longer turn the hub by hand.

„„Loosen the spindle nut just until you are able to turn it (the spindle nut) by hand. Do not turn the hub while the spindle nut is loose.

„„Install a new cotter pin through the spindle nut and axle.

„„Check the adjustments. Both the hub and the spindle nut should be able to move freely (the spindle nut motion will be limited by the cotter pin).

DANGER

NEVER crawl under the trailer unless it is on firm and level ground and resting on properly placed and secured jackstands.

The possibility exists of the trailer falling thus causing equipment damage and severe bodily harm even death!

DANGER

When performing trailer inspection and maintenance activities, you must jack up the trailer using jacks and jackstands.

When jacking and using jackstands, place them so as to clear wiring, brake lines, and suspension parts (i.e., springs, torsion bars). Place jacks and jackstands inside of the perimeter strip on the supporting structure to which the axles are attached.

DANGER

Improper weld repair will lead to early failure of the trailer structure and can cause serious injury or death.

DO NOT repair cracked or broken welds unless you have a certified welder perform the repair. If not, have the welds repaired by your dealer.

WARNING

If the trailer is involved in an accident, have it inspected immediately by qualified personnel. In addition, the trailer should be inspected annually for signs of wear or deformations.

Leaf Suspension

The leaf suspension springs and associated components (Figure 17) should be visually inspected every 6,000 miles for signs of excessive wear, elongation of bolt holes, and loosening of fasteners. Replace all damaged parts (suspension) immediately.

Figure 17. Leaf Suspension Components

DANGER

Worn or broken suspension parts can cause loss of control, damage to equipment and severe bodily injury, even death!

Check suspension regularly.

page 26 — MLT20 sERIES LIGHT TOWER • operation manual — rev. #0 (01/18/13)

Image 26
Contents Models Proposition 65 warning Reporting Safety Defects NhtsaTable of Contents Specifications are subject to change without noticeSaFeTY sYMBOLs Safety InformationSaFeTY Messages Addresses practices not related to personal injuryGeneRaL saFeTY LIgHT TOWeR saFeTY LaMp saFeTYTOWIng saFeTY TRanspORTIng saFeTY Loading and Tie-Down on Flatbed TruckELeCTRICaL saFeTY „ neveR operate light towerGenerator/Engine Specifications MLT20 Series SpecificationsLight Tower Specifications Reference Letter Description Dimension DimensionsDimensions Length Mast Stowed Position Length Mast Deployed PositionGeneral information Metal Halide LampsComponents Major Components Control Panel SideCircuit Breakers Turn the lamps on and off Major Components Front/RearBefore starting Read all safety instructions at the beginning of manualInspection Check all fastening nuts and bolts for tightnessContact between the two connectors Female and Male ConnectorMast operation OperationStarting the Engine Outriggers and Support StandsRaising the Mast Stowing the Mast to Horizontal Position Raising the MastLowering the Mast Rotating the MastVoltage Regulator Knob and AC Voltmeter Check Cable Wear MaintenanceGenerator/ENGINE Maintenance Servicing the Mast Raise/Lower Cable SystemServicing the Mast Extension Cable System Lower the mast to the horizontal resting positionTrailer Brakes Maintenance TrailersManually Adjusting the Brakes Hydraulic BrakesAdjustable Channel Hydraulic Brake TroubleshootingWheel Hub Adjustment Leaf SuspensionTRaILeR TOWIng guIDeLInes Safety guidelines TrailersCOMMOn Causes for LOss of TRaILeR DRIvIng COnDITIOns COupLIng to THe TOW veHICLeTRaILeR vIn Tag InOpeRaBLe BRaKes, LIgHTs or MIRRORsTRaILeR TOWIng TIps SuspensIOn sYsTeM ELeCTRICaL COnneCTORTOW veHICLe BRaKe COnTROLLeRBReaKaWaY sYsTeM SaFeTY CHaInsTRaILeR LIgHTIng anD BRaKIng COnneCTOR JaCKsTanDCoupling the Trailer to the Tow vehicle Ball Coupler Lock washer and hitch frameTrailer tongue. Wood or concrete blocks may also be used Breakaway Cable surge Brake system Attaching safety ChainBreakaway Brake system PInTLe Hitch COupLeR Connecting Trailer LightsUncoupling the Ball Hitch Pintle Coupler and pintle HookFigure H. Attaching Safety Chain Pintle Hitch Coupling Trailer to Tow vehicle pintle CouplerBe sure lug nuts are tight before each tow TIRe saFeTY Unsafe Tires, Lug nuts or WheelsDetermining Load Limit of Trailer Step Determining Load Limit of Tow vehicle stepLetter Rating Speed Rating TIRe FunDaMenTaLsTable a. speed Rating Replacing Worn or Damaged Tires Tire safety TipsTire Repair Uniform Tire Quality grading standards uTQgsWheels, Bearings and Lug nuts Table B. Tire Wear TroubleshootingWheel Rims Lug nut Torque RequirementsLights and signals Table C. Tire Torque RequirementsLamp Troubleshooting Symptom Possible Cause SolutionClean fixture When switch is first Checking voltage and ballast Turned onReplacement minimizes color differences Lamp starts slowly ARC does not strike Defective Lamp?Starting Lamp Troubleshooting GuideConnections Ballast RemovalPage Reference MLT20DCA 4-lamp wiring diagram on succeeding pages Electronic Component Locator mlt20dcaElectronic Component Locator mlt20dca6 Wiring Diagram mlt20dca TB1 N Wiring Diagram mlt20dca6 TB1 Z HERE’S HOW to GET Help

MLT20DCA6, MLT20DCA specifications

The Multi Tech Equipment MLT20DCA and MLT20DCA6 stand out in the realm of compact construction machinery, renowned for their versatility and efficiency. These models are designed to meet the demanding needs of various industries, including construction, landscaping, and agricultural operations.

One of the key features of the MLT20DCA series is its powerful and reliable engine. Equipped with a robust diesel engine, these machines deliver optimal performance and fuel efficiency, ensuring that operators can complete tasks quickly and economically. This powertrain is complemented by a highly responsive hydraulic system, which allows for seamless operation of attachments such as buckets, forks, and augers.

The ergonomic design of the MLT20DCA and MLT20DCA6 enhances operator comfort and productivity. The spacious cabin is equipped with intuitive controls and offers excellent visibility, making it easier for operators to navigate tight spaces and perform intricate tasks. The low center of gravity provides stability and balance, which is essential when working on uneven terrain.

Both models feature a compact design, making them ideal for urban environments and confined job sites. Their versatile lifting capabilities allow them to handle a wide range of materials, from heavy loads to delicate items, making them invaluable in various applications. The MLT20DCA6 variant offers additional lifting height and capacity, catering to heavier-duty operations.

Safety is a paramount concern in equipment design, and the MLT20DCA series does not disappoint. These machines are equipped with multiple safety features, including reinforced ROPS (Roll Over Protective Structure), safety interlocks, and improved braking systems. This ensures the well-being of operators and those working in proximity.

In terms of technology, Multi Tech has integrated advanced control systems into both models. This includes automated diagnostics that monitor machine performance and alert users to potential issues before they become significant problems. Connectivity features also allow for remote monitoring, enhancing fleet management capabilities.

In summary, the Multi Tech Equipment MLT20DCA and MLT20DCA6 represent a formidable option for professionals seeking reliable and efficient compact machinery. With their powerhouse engines, user-friendly design, and advanced safety and technology features, these machines are poised to enhance productivity across various applications, ensuring a strong return on investment for operators.