Fixing the installation plate

Samsung AQ09TSBN Fixing the installation plate, Optional accessories, Tools for test operations

Page 27

Optional accessories

The following connection accessories are optional. If they are not supplied, you should obtain them before installing the air conditioner.

Insulated	Insulated Assembly	Insulated Assembly Pipe,	Insulated Assembly Pipe,	PE T3 Foam Tube	Vinyl Tapes (2)	Drain Plug (1)
Assembly Pipe,	Pipe, Ø9.52mm (1)	Ø12.70mm (1)	Ø15.88mm (1)	Insulation (1)
Ø6.35mm (1)	09	12/18	24

Rubber Legs (4)	Pipe Clamps A (3)	Pipe Clamps B (3)	Cement Nails (6)	M4 x 25 Tapped	Drain Hose,	Putty 100g (1)
				Screws (6)	length 2m (1)

ENGLISH

• If these accessories are supplied, they will be in the accessory box.

Tools required for installation

General Tools

• Vacuum Pump(Backward flowing prevention)			• Manifold Gauge	• Stud Finder
• Torque Wrench	• Pipe Cutter	• Reamer	• Pipe Bender	• Spirit Level
• Screw Driver	• Spanner	• Drill	• L Wrench	• Measuring Tape

Tools for test operations

• Thermometer

• Resistance Meter • Electroscope

You can select the direction of the drain hose depending on where you want to install the indoor unit. Therefore before fixing the installation plate to a wall or a window frame, you must determine the position of the 65mm hole through which the cable, pipe and hose pass to connect the indoor unit to the outdoor unit.

When facing the wall, the pipe and cable can be connected from the:

• Right (A)		 Direction of pipe
• Left (B)
• Underside_right (C)
• Rear_right or left (D)	A		B
	A		B
		D	D
		C

1. Determine the position of the pipe and drain hose hole as seen in the picture and drill the hole with an inner diameter of 65mm so that it slants slightly downwards.

Pipe hole
(Ø65mm)
A	D
B	C

(Unit : mm)

Model	A	B	C	D
09/12	27	120	68	27
18/24	34	140	68	34

•Make sure to drill only one hole after choosing the direction of the pipe.

Boracay EUR_AQ09T&U@_IBIM_32447A_EN-4.indd 27

2015/7/7 14:56:37

Image 27

Contents

Boracay EURAQ09T&U@IBIM32447AEN-4.indd 2015/7/7 Contents Wall socket Safety precautionsImportant safety symbols and precautions Follow directionsFor Using For Cleaning Operation ranges Checking before useDisplay  09/12/18/24T PowerChecking the name of the parts Main parts  09/12/18/24T Remote controller buttons Checking the remote controllerIndicator Remote controller displayBattery changing time Storing the remote controllerBasic function Auto Auto Low Med HighLow Med High Vertical air flow Adjusting the air flow directionUsing the Turbo function Press the Air swing button on the remote controllerPress the Time Up or Time Down button to set the time When the air conditioner is on and in cool/heat modePress the button on the remote controller ModeSetting the On/Off timer Press the On Timer/Off Timer buttonAdditional options available in On timer mode Turn off automatically Using the Smart Saver functionFrom the moment you have set the timer If the air conditioner is on If the air conditioner is offUsing the Auto Clean function When the air conditioner is turned on09/12/18/24T 09/12/18/24U Opening the panel Cleaning the air conditionerCleaning the indoor unit Cleaning the outdoor unit heat exchangerDry the Air filter in a ventilated area Cleaning the air filterRemoving the Air filter Open the panel and put the Air filter outPeriodical checks Maintaining the air conditionerTroubleshooting Outdoor unit Heat exchanger during Heat mode in winter Flow movement changes. It is normalConnection General information  a place where the air filter can be replaced easily Choosing the installation locationInstalling the unit Power supply line, fuse or circuit breakerWhere sulfide gas exists Outdoor UnitModel Top view Side view When installing more than 1 outdoor unitWhen the air outlet is towards the wall  Figure DescriptionAccessories Accessories in the indoor unit caseAccessories in the outdoor unit case Tools for test operations Fixing the installation plateOptional accessories Tools required for installation General ToolsConnecting the assembly cable Cable specificationConnecting the cable Each wire is labeled with the corresponding terminal number Smooth the cut edges TorqueCut off the remaining foam insulation Put a flare nut slightly into the pipe and modify the flare Purging the indoor unitCutting or extending the pipe Unscrew the caps at the end of each pipeDitch Pipe 50 Pa. The joint must be accessible and serviceableCorrect Inclined CrackedDrain hose installation Outer Torque Purging the connected pipesConnect a drain hose to the drain plug Ensure that condensation draining is adequateIf you use a pipe shorter than 5m Gas service port as seen in the pictureAdding Refrigerant If you use a pipe longer than 5mPlease fill in with indelible ink  the factory refrigerant charge of the product1975 Leak test after opening valves Performing the gas leak testsTightening torque To check for gas leaks on the outdoor unitThen place the indoor unit on the installation plate Fixing the indoor unit in placeFixing the outdoor unit in place Final Check and Trial Operation Insulation tape to finish How to connect your extended power cablesApply heat to the contraction tube to contract it After tube contraction work is completed, wrap it withMemo Questions or COMMENTS? Thank you for purchasing this Samsung product Air Conditioner

Related manuals

Samsung AQ09TSBN Fixing the installation plate, Optional accessories, Tools for test operations