Flow movement changes. It is normal, Connection

Samsung AQ12UGFX, AQ18UGAN, AQ24TSBXEUR, AQ18TSBN Flow movement changes. It is normal, Connection

Page 21

PROBLEM

SOLUTION

Error is indicated.

• When an indoor unit indicator blinks, contact the nearest service center.

Noise is generated.

• Depending on the status of the air conditioner usage, noise can be heard when refrigerant

flow movement changes. It is normal.

Smoke is generated from

• If may not be a fire but it can be a steam generated by the defrost operation from outdoor

the outdoor unit.

heat exchanger during Heat mode in winter.

Water is dropping from

• Water may be generated because of the temperature difference. It is normal.

the outdoor unit piping

connection.

ENGLISH

Boracay EUR_AQ09T&U@_IBIM_32447A_E.indd 21

2011-3-19 10:07:54

Image 21

Contents

Boracay EURAQ09T&U@IBIM32447AE.indd 2011-3-19 Contents Important safety symbols and precautions Safety precautionsFollow directions Wall socketFor Using For Cleaning Operation ranges Checking before useChecking the name of the parts PowerMain parts  09/12/18/24T  Display  09/12/18/24TRemote controller buttons Checking the remote controllerBattery changing time Remote controller displayStoring the remote controller IndicatorBasic function Auto Auto Low Med HighLow Med High Using the Turbo function Adjusting the air flow directionPress the Air swing button on the remote controller Vertical air flowPress the button on the remote controller When the air conditioner is on and in cool/heat modeMode Press the Time Up or Time Down button to set the timeSetting the On/Off timer Press the On Timer/Off Timer buttonAdditional options available in On timer mode Combining On Timer and Off Timer Using the Smart Saver functionUsing the Auto Clean function When the air conditioner is turned on09/12/18/24T 09/12/18/24U Cleaning the indoor unit Cleaning the air conditionerCleaning the outdoor unit heat exchanger Opening the panelRemoving the Air filter Cleaning the air filterOpen the panel and put the Air filter out Dry the Air filter in a ventilated areaPeriodical checks Maintaining the air conditionerTroubleshooting Outdoor unit Heat exchanger during Heat mode in winter Flow movement changes. It is normalConnection General information Installing the unit Choosing the installation locationPower supply line, fuse or circuit breaker  a place where the air filter can be replaced easilyWhere sulfide gas exists Outdoor UnitModel When the air outlet is towards the wall When installing more than 1 outdoor unit Figure Description Top view Side viewAccessories Accessories in the indoor unit caseAccessories in the outdoor unit case Optional accessories Fixing the installation plateTools required for installation General Tools Tools for test operationsConnecting the assembly cable Cable specificationConnecting the cable Each wire is labeled with the corresponding terminal number Cut off the remaining foam insulation Smooth the cut edgesCutting or extending the pipe Purging the indoor unitUnscrew the caps at the end of each pipe Put a flare nut slightly into the pipe and modify the flareCorrect Inclined Pipe 50 Pa. The joint must be accessible and serviceableCracked Outer DiameterDrain hose installation Purging the connected pipes Connect a drain hose to the drain plugEnsure that condensation draining is adequate Adding Refrigerant Please fill in with indelible ink  the factory refrigerant charge of the product1975 To check for gas leaks on the outdoor unit Performing the gas leak testsTo check for gas leaks on the indoor unit Leak test with nitrogen before opening valvesThen place the indoor unit on the installation plate Fixing the indoor unit in placeFixing the outdoor unit in place Final Check and Trial Operation Apply heat to the contraction tube to contract it How to connect your extended power cablesAfter tube contraction work is completed, wrap it with Insulation tape to finishMemo 7267864, € 0.07/min 42 2770 70 19 +381Air Conditioner

Related manuals

Samsung AQ12UGFX, AQ18UGAN, AQ24TSBXEUR, AQ18TSBN Flow movement changes. It is normal, Connection