Connecting the assembly cable

Samsung AQ18UGFXEUR Connecting the assembly cable, Cable specification, Connecting the cable

Page 28

Fixing the installation plate

2. Fix the indoor unit.

If you fix the indoor unit on a wall

(1) Fix the installation plate to the wall giving attention to the weight of the indoor unit.

• If you mount the plate to a concrete wall using plastic anchors, make sure that

Plastic

gaps between the wall and the plate, created by projected anchor, is less than

Anchor

<20mm

20mm.

If you fix the indoor unit on a window frame

If you fix the indoor unit on a gypsum board

Wall

(1)Determine the positions of the wooden uprights to be attached to the window frame.

(2)Attach the wooden uprights to the window frame giving attention to the weight of the indoor unit.

(3)Attach the installation plate to the wooden upright using tapping screws.

(1)Use stud finder to find out locations of the studs.

(2)Fix the plate hanger on two studs.

• Search for other spots if there are less than two studs, or the distance between the studs are different from the plate hanger.

•Fix the installation plate without inclining to one side.

•Make sure that a wall can withstand the weight of the product. If you install the product in a place where it is not

strong enough to withstand the product weight, the unit could fall and cause injury.

Cable specification

Model	Power cable	Interconnection cable	Type GL



09/12	3G, 1.0mm² H07RN-F	5G, 1.0mm² H07RN-F	20A

18	3G, 1.5mm² H07RN-F	2G, 0.75mm² H05RN-F
18	3G, 1.5mm² H07RN-F	3G, 1.5mm² H07RN-F	25A
		3G, 1.5mm² H07RN-F
24	3G, 2.5mm² H07RN-F	3G, 2.5mm² H07RN-F
		3G, 2.5mm² H07RN-F
		2G, 0.75mm² H05RN-F
		2G, 0.75mm² H05RN-F

• Connect the power cable to the auxiliary circuit breaker. If every pole fails to connect to

the power supply, it must be incorporated in a wire with a contact opening of ≥3mm.

Connecting the cable

When you install the unit, make first refrigerant connections and then electrical connections. Connect the air conditioner to grounding system before performing the electrical connection. If unit is uninstalled, first disconnect electrical cables, then refrigerant connections.

If the outdoor unit is more than 5 meters away from the indoor unit, you must extend the cable.

The maximum length of the cable is 15(09/12)/20(18/24) meters.

1. Extend the assembly cable if necessary.

• Do not connect two or more different cables to extend the length. It may cause fire.

Boracay EUR_AQ09T&U@_IBIM_32447A_E.indd 28

2011-3-19 10:08:09

Image 28

Contents

Boracay EURAQ09T&U@IBIM32447AE.indd 2011-3-19 Contents Safety precautions Important safety symbols and precautionsFollow directions Wall socketFor Using For Cleaning Checking before use Operation rangesPower Checking the name of the partsMain parts  09/12/18/24T  Display  09/12/18/24TChecking the remote controller Remote controller buttonsRemote controller display Battery changing timeStoring the remote controller IndicatorBasic function Auto Low Med High AutoLow Med High Adjusting the air flow direction Using the Turbo functionPress the Air swing button on the remote controller Vertical air flowWhen the air conditioner is on and in cool/heat mode Press the button on the remote controllerMode Press the Time Up or Time Down button to set the timePress the On Timer/Off Timer button Setting the On/Off timerAdditional options available in On timer mode Using the Smart Saver function Combining On Timer and Off TimerWhen the air conditioner is turned on Using the Auto Clean function09/12/18/24T 09/12/18/24U Cleaning the air conditioner Cleaning the indoor unitCleaning the outdoor unit heat exchanger Opening the panelCleaning the air filter Removing the Air filterOpen the panel and put the Air filter out Dry the Air filter in a ventilated areaMaintaining the air conditioner Periodical checksTroubleshooting Flow movement changes. It is normal Outdoor unit Heat exchanger during Heat mode in winterConnection General information Choosing the installation location Installing the unitPower supply line, fuse or circuit breaker  a place where the air filter can be replaced easilyOutdoor Unit Where sulfide gas existsModel When installing more than 1 outdoor unit When the air outlet is towards the wall Figure Description Top view Side viewAccessories in the indoor unit case AccessoriesAccessories in the outdoor unit case Fixing the installation plate Optional accessoriesTools required for installation General Tools Tools for test operationsCable specification Connecting the assembly cableConnecting the cable Each wire is labeled with the corresponding terminal number Smooth the cut edges Cut off the remaining foam insulationPurging the indoor unit Cutting or extending the pipeUnscrew the caps at the end of each pipe Put a flare nut slightly into the pipe and modify the flarePipe 50 Pa. The joint must be accessible and serviceable Correct InclinedCracked Outer DiameterDrain hose installation Connect a drain hose to the drain plug Purging the connected pipesEnsure that condensation draining is adequate Adding Refrigerant  the factory refrigerant charge of the product Please fill in with indelible ink1975 Performing the gas leak tests To check for gas leaks on the outdoor unitTo check for gas leaks on the indoor unit Leak test with nitrogen before opening valvesFixing the indoor unit in place Then place the indoor unit on the installation plateFixing the outdoor unit in place Final Check and Trial Operation How to connect your extended power cables Apply heat to the contraction tube to contract itAfter tube contraction work is completed, wrap it with Insulation tape to finishMemo 42 27 7267864, € 0.07/min70 70 19 +381Air Conditioner

Related manuals

Samsung AQ18UGFXEUR Connecting the assembly cable, Cable specification, Connecting the cable

Fixing the installation plate

2. Fix the indoor unit.

If you fix the indoor unit on a wall

If you fix the indoor unit on a window frame