Samsung SVR960JP, SVR24JP Series Recording, Alarm Recording, When pressing the Reset button

2001-1-1 MON 12:00:00 L3H

SERIES RECORDING

This is a convenient function in which when two or more VCRs are connected the second unit starts recording when the tape on the first unit reaches the end.

Connecting	Operating	Description
method	method	of operation
Refer to the	• Select to No. 4 in the MENU	• When the tape in the first unit
connection	• Select to "ON" for SERIES	arrives at its end during
method for	using the SHIFT ❷!and ❿	recording, the second unit begins
series recording	button.	recording. When the tape in the
(page 37)		second unit arrives at its end and
		during recording, the next unit
		begins recording if connected.
		• When the series recording mode
		is selected, the second unit
		performs recording even if the
		power is turned off.
		• As a constant alarm sounding,
		you can clear it by only pressing
		any key.

ALARM RECORDING

If the VCR is connected to equipment with an alarm output such as a frame switcher, motion detector or door switch, the VCR will function according to the time and mode selected on the ALARM REC menu when an alarm is received.

SVR-24JP has only L3H/L12H/L24H mode for ALARM REC. The below diagram is set L3H mode for ALARM REC.

		L12H~960H		L3H	L12H~960H		L3H
		(L12H~L24H)*			(L12H~L24H)*
			mode recording				mode recording
		mode recording			mode recording
	Timelapse recording		Alarm recording		Timelapse recording		Alarm recording
Start of		Enter of		Enter of alarm reset		Enter of
recording		alarm signal		or over selected time		alarm signal

	Connecting								Operating		Description of
			method						method		operating
Connect the alarm									• Select to MODE and	• AUTO: The alarm recording time is
output equipment									DURATION on	automatically determined by input of
as follows;									ALARM REC SETUP	the alarm signal. (1 minute)
									in setting MENU3.	• 20sec~5min: Alarm recording is made
										for 20 seconds~5 minutes after input of
									(Refer to ALARM
6	TAPE END OUT 7		SERIES OUT 8	GND	9	SERIES IN	10	1 SHOT RECIN		the alarm signal.
1	ALARM IN	2	ALARM OUT 3	ALARM RESET 4		ERROR OUT	5	TRIGGER OUT
	1	2	3 4 5 6		7	8	9	10	REC SETUP, page 16)	• TAPE END: Alarm recording is made
IN									• When connecting with	up to the end of the tape after input of
				IN		OUT			FRAME SWITCHER, it	the alarm signal.
OUT										• When the alarm signal is entered, the
AUDIO					VIDEO				is convenient, if the
										on the front display is turned on.
									switch is placed in
										• When the alarm recording is ended,
									automatic position.	the	on the front display flashes.
	VIDEO				GND			ALARM		• When you want to cancel the alarm
	OUT							OUT		during alarm recording, make a
										connection between the alarm release
			ALARM							and the alarm grounding for more than
										0.5 second, when the alarm release is
			RESET
(Refer to page 37)										entered, the alarm recording is
										stopped.
										• When an alarm signal is received and
										the BUZZER ON is selected in the
										menu, the alarm sounds continuously.
										To silence the buzzer, press any
										button.

RECORDING

REFERENCE

RESET button

•Use this button when the VCR or display does not operate normally even though the power is turned on.

•The RESET button is on the right side of the Front Panel.

•Press the RESET button using a ball point pen or a pencil.

When pressing the RESET button

•All the entered information such as reserve recording set time, current time, and alarm information is erased.

•The power is turned off, and there is no picture at all. When

the power is turned on again,flashes on the display of the screen.

• The current time is erased and must be reset.

31 32