Thomas & Betts RZ405, RGM 405 dimensions Model Caua, Table of Contents

Page 1

C E R T I F I E D

Model CAUA

Gas-Fired, Indoor, Vertical (Upflow) Power-Vented Heater

INSTALLATION FORM RZ 405 (Version B)

Obsoletes Form RGM 405 (Version A)

APPLIES TO:Installation

Table of Contents

Installation and Operation

Paragraphs 1-18

.... Pages 1-18

Optional Accessories

Paragraphs 19-21

.. Pages 19-21

Check Installation and Start-Up

Paragraph 22

.. Pages 22-23

Index

By Page No.

Index

By Page No.

Index

By Page No.

Belt Drive

15

Discharge Plenum (Optional)

............

2, 21

Motor Amps

16

Blower Motor and Drive

15

Duct Connections

12

Mounting the Heater

2

Check/Test/Start-Up

22

Electrical Supply and Connections

14

Start-Up

22

Clearances

2

Filter Cabinet (Optional)

2, 20

Thermostat

14

Combustion Air

4

Gas Piping and Pressures

13

Uncrating and Preparation

2

Combustion Air Proving Switch

15

Gas Valve

16

Vent and Combustion Air

4

Concentric Adapter

2, 5

General

1

Determine Type of Vent

4

Condensate Drain

14

Hazard Intensity Levels

2

Power Vent Only Installation

10-11

Confined Space Installation

10

Ignition System

16

Separated-Combustion Installation ...

5-9

Cased Cooling Coil (Model ACU)

2, 19

Inlet Base (Optional)

2, 21

Warranty

2

Control Location Illustration

.................

15

Installation Codes

2

Wiring Diagrams

17-19

Dimensions

3

Mixing Cabinet (Optional)

2, 21

 

 

 

REFERENCES:

Installation Manual for Optional Filter Cabinet, RZ 405-FC

Operation/Maintenance/Service Manual, Form RZ 405-OMS

Installation Manual for Optional Mixing Box, RZ 405-MB

Installation Manual for Model ACU Cooling Coil, RZ 405-CC

Installation Instructions for Optional Inlet Base, RZ 405-IB

Gas Conversion Instructions for Model CAUA, RZ 405-GC

Installation Instructions for Optional Discharge Plenum, RZ 405-DP

FOR YOUR SAFETY

What to do if you smell gas:

Do not try to light any appliance.

Do not touch any electrical switch; do not use any phone in your building.

Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions.

If you cannot reach your gas supplier, call your fire department.

WARNING: Improper installation, adjustment, alteration, service, or maintenance can cause property damage, injury, or death. Refer to this manual. For assistance or additional information, consult a qualified installer, service agency, or the gas supplier.

WARNING: Gas-fired appliances are not designed for use in hazardous atmospheres containing flammable vapors or combustible dust. See Hazard Levels, page 2.

FOR YOUR SAFETY

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

GENERAL

Installation should be done by a qualified agency in accordance with the instructions in this manual and in compliance with all codes and re- quirements of authorities having jurisdiction. The instructions in this manual apply to the heater model shown below.

Model

Description

CAUA

Gas-Fired,

 

Power-Vented,

 

Vertical (Upflow)

 

Heater

Model CAUA heaters are design-certified by the Canadian Standards Association (CSA) to ANSI Z83.6 and CGA 2.6-M96 for industrial/ commercial installations in the United States and Canada. Heaters are available for use with either natural or propane gas. The type of gas, the firing rate, and the electrical characteristics are on the unit rating plate.

A Model CAUA heater requires installation of an inlet air duct or an optional inlet air base and a supply duct or an optional discharge ple- num. This heater may be installed as a separated-combustion system (taking combustion air from outside) or as a power-vented system (taking combustion air from the space where the heater is installed).

Mfg No. 164771, Page 1

Image 1
Contents Model Caua Table of ContentsWarranty Clearances Installation CodesGeneral Contd Mounting the HeaterDimensions inches + or 1/8 DimensionsDimensions mm +or Air Opening DimensionsVenting and Combustion Air Decide which Venting System to InstallCommercial Indus TrialVenter Outlet Combustion Air InletConcentric Adapter Joints Venting and Combustion Air contdSupport ClearanceInlet air pipe Flash or caulkOn the outside Wall2b Install the rubber seal Installation Instructions for Option CC2Side View Clearance 559mm minimum SnowExhaust TerminalVenter Flue Outlet Vent Pipe and JointsVent Pipe Diameter and Length Vent System SupportVent Terminal Pipe and Vent Cap CondensationHorizontal Vent Terminal Clearances Cut edges of the metal will be sharp Duct Connections and DuctworkSize 150 250 350 36 914mm 48 1219mm 21 533mm 34 864mm Gas Piping and Pressures Manifold or Orifice Pressure SettingsSizing a Gas Supply Line Supply PipingGas Piping and Pressures contd Manifold Pressure Settings contdBurner Condensate Drain Electrical Supply and ConnectionsBlower Motor and Drive Combustion Air Proving SwitchDirect Drive Belt DriveBlower Motor and Drive contd Adjusting Blower SpeedGas Valve Ignition SystemTypical Wiring Diagrams Typical Wiring Diagrams contd Optional Cased Cooling Coil, Model ACUA, ACUB, or Acuc Low Voltage Wiring field-suppliedBurner Condensate Drain Electrical ConnectionsMixing Cabinet Outside and Return Air 400 only Discharge Plenum SizesInlet Base Sizes 350 and 400 only Optional Outside Air Return Air Mixing BoxCheck the installation prior to start-up Check/Test/Start-Up Check Installation & Start-UpStart-Up 250To Turn OFF GAS to the Appliance Check installation after start-upManufacturer of HEATING, COOLING, and Ventilating Systems