Tripp Lite Air Conditioner Manual - SRCOOL33K Installation and Safety Instructions

1. Important Safety Instructions

SAVE THESE INSTRUCTIONS

This manual contains instructions and warnings that must be followed during the installation of the products described in this manual. Read ALL instructions before attempting to install these products. Failure to comply may invalidate the warranty and cause serious property damage and/or personal injury. Also see the safety instructions contained in the SRCOOL33K/SRXCOOL33K Unpacking Instructions and Owner’s Manual.

2. Preparing the Installation Site

The SRCOOL33K/SRXCOOL33K provides a self-contained cooling solution for small server rooms, wiring closets and similar applications. It is also suitable for supplemental cooling in large IT rooms and data centers. The following installation instructions are applicable to any application.

•Ensure that the room in which the SRCOOL33K/SRXCOOL33K will be installed is insulated to minimize thermal loads.

•To minimize migration of moisture, it is recommended that the room be sealed with a vapor barrier, e.g. polyethylene sheeting. Concrete floors and walls should be treated with a rubber- or plastic-based paint.

•Condenser airspace MUST be capable of dissipating up to 16kW (55kBTU) of heat and supplying air between 0-40° C (32-104° F) to and from the unit at a rate of 1720 m3/hr (1012 CFM).

•A minimum of 36 in. (914 mm) of clear floor space in front of and behind the unit is required for routine service/repair access. For major repairs requiring side access, 20 in. (508 mm) of clear space on either side must be provided. This may necessitate moving the unit from its installation site. At least 48 in. (1219 mm) of clear floor space is required to provide complete front, rear and side access.

•Ensure that appropriate electrical service (Nominal 208-240V AC input, 50/60 Hz) is available at the installation site. The SRCOOL33K is furnished with two points of mains power input and can receive power via attached 10-ft. power cord with L6-30 plug or hardwire connections. The SRXCOOL33K can receive power via hardwire connections or user supplied IEC 309 32 amp cord set.

3. Positioning the Unit

Using a forklift or pallet jack, move the unit as close to its permanent installation location as possible before unpacking it and removing it from the shipping pallet. See the SRCOOL33K/SRXCOOL33K Unpacking Instructions for full details.

Select an installation site that is structurally sound, with a level floor that is able to bear the weight of the unit, plus any other racks and/or equipment that will be installed nearby. Ensure that the installation site provides sufficient front, back and side clearances. The unit can be positioned in a row of rack enclosures, or in a stand-alone configuration.

Prior to final placement, use a carpenter’s level to check the slope of the floor. If the floor slope is excessive, choose another installation site.

The unit is furnished with casters for final placement in its installation location. The casters are intended to move the unit over a short distance on a level, smooth, stable surface only. They are not designed to roll the unit over long distances. WARNING: When rolling the unit, do not pull it toward you. Push it into position.

4. Leveling the Unit

After the unit is positioned in its permanent installation location, it must be leveled. Using an 18 mm open-end wrench, lower each leveler until it reaches the floor. (There are four levelers, two at the front and two at the rear.) Make sure each leveler contacts the floor solidly. Lower a leveler by turning it clockwise; raise a leveler by turning it counter-clockwise.

After lowering each leveler, use a carpenter’s level to confirm that the unit is level in all directions. Adjust the levelers as required until the unit is level.

SRCOOL33K, SRXCOOL33K specifications

The Tripp Lite SRXCOOL33K is a premier portable air conditioning unit designed specifically for cooling server rooms, data centers, and other critical environments where temperature control is paramount. With its effective cooling capabilities and user-friendly design, this unit is an essential tool for IT professionals seeking reliable temperature management solutions.

One of the primary features of the SRXCOOL33K is its impressive cooling capacity. With a powerful output of 33,000 BTUs, it can efficiently cool spaces up to 1,000 square feet, making it ideal for larger rooms or areas with a high concentration of heat-generating equipment. This capacity is particularly critical in maintaining optimal operating conditions for servers and networking equipment, which can be adversely affected by elevated temperatures.

In addition to its cooling prowess, the SRXCOOL33K incorporates advanced technologies that enhance its performance. The unit utilizes a high-efficiency rotary compressor, which not only improves cooling efficiency but also reduces energy consumption. This energy-efficient design can lead to significant cost savings on utility bills, making it a smart investment for any organization.

The SRXCOOL33K also features a host of user-friendly characteristics, making it straightforward to operate and maintain. The digital control panel allows users to set and monitor temperatures with precision, while the included remote control adds convenience for adjusting settings from a distance. Furthermore, the unit is equipped with a programmable timer, enabling scheduled operation to match peak cooling needs.

Portability is another standout feature of the SRXCOOL33K. With easy-rolling casters and side handles, it can be effortlessly moved to different locations as required. This flexibility is particularly advantageous for organizations that may need to reposition their cooling solutions in response to varying equipment loads or spatial configurations.

The air conditioner also includes a built-in condensate pump that automatically removes water collected during operation, eliminating the need for manual drainage. This adds to its low-maintenance nature, allowing IT staff to focus on their core tasks without the hassle of frequent upkeep.

In conclusion, the Tripp Lite SRXCOOL33K stands out as a robust and versatile cooling solution for professionals in the IT and data management sectors. With its exceptional cooling capacity, energy-efficient technologies, and portability, it effectively supports maintaining the ideal conditions for critical equipment.