Samsung AF28HVSDADFNMG manual Indoor/outdoor unit installation diagram

Page 39

Indoor/outdoor unit installation diagram

Installation space for floor type indoor unit

ffTo minimize the waste of space due to installation, install the indoor unit as shown in below figure.

-- Top view ❋❋ After completing the installation, remove the protection vinyl.

50cm or more

Protection vinyl

CAUTION

(Be careful of static electricity).

❋❋ After completing the installation, remove the protective filament film on the product.

• Make sure that there are no obstacles (such as curtains etc.) blocking air inlets of the indoor unit.

• Clear space on the right side of the indoor unit for possible filter maintenance in the future.

Piping length for indoor/outdoor unit installation

Noobstaclemore or 1m

Maximum

6m or

less

allowable piping

 

elevation 10m

 

Install S-trap for every 6m

Maximum allowable piping length 20m or less

ffRefer to illustration on the left for maximum allowable piping length and elevation.

ffSince product performance and lifespan may decrease as piping length becomes longer, try to minimize the piping length but make sure it is over 5m.

ffSelect the installation location where you can keep the piping bending to maximum 10 spots.

ffStated cooling performance is based on product with 5m piping.

• One S-trap must be installed on the low pressure

CAUTION pipe up to 6m of piping elevation. For piping elevation that exceeds 6m, install S-trap every

6m.

or less

 

30cm or more

or

 

 

 

 

Outdoor unit

30cm

 

 

more

30cm or

Air guide

 

 

(Not provided by

 

 

more

 

 

manufacturer )

50cm

 

 

or

 

 

 

more

more

 

 

 

 

or

 

 

 

60cm

 

 

Outdoor

 

 

unit leg

 

 

 

Rubber leg

20cm or more

 

 

 

 

Spare space for piping

When air guide needs to be installed to prevent the warm discharge air from disturbing the pedestrian, refer to the illustration on the right side for installation.

38

사우디,인도,나이지리아향 FAC MEMORY 냉방_IBIM_EN_04773A-00.indd 38

2014-09-11 오후 1:16:11

Image 39
Contents This product is RoHS compliant Questions or COMMENTS?Thank you for purchasing this Samsung product Air ConditionerApplicable to AF28HVSDAN only Features of your new air conditionerSeasons of effective cleaning Smart sensorContents Injury or property damage Safety precautionsFfThis may result in electric shock or fire For Power Supply Warning For Using Do not place objects or devices under the indoor unit For Cleaning Do not clean the inside of the air conditioner by yourself Checking before use Using indoor unitUsing outdoor unit Installing outdoor unitFunctions available for each model Auxiliary power switchAuxiliary power switch NFB, ELB, etc Operation rangesIndoor unit Checking the name of the partsButtons on control panel DisplayConditioner will operate with auto mode Operation with control panelFan speed of each air outlet will differ Remote controller buttons Checking the remote controllerInserting the batteries Remote controller displayBattery changing time Storing the remote controllerDry Basic operationAuto CoolSolomode Remarks Press the button to adjust the desired temperatureExcept in Auto mode Press the button to turn on the air conditionerAir flow direction Press the button on the remote controller in the Cool modeTurbo function is only available in the Cool mode Turbo operationGoodsleep operation When the air conditioner is on and in cool modeTemperature and fan speed changes in goodsleep mode Goodsleep functions Setting the On/Off timerAir conditioner will turn on after 3 hours Your air conditioner will turn onLighting function Press the button during Cool modeTo adjust the lighting level of an indoor unit Smart sensor operationQuiet operation Auto clean operationProduct can be scratched easily Cleaning the air conditionerCleaning the indoor unit Cleaning the outdoor unit heat exchangerPull out the Full HD filter in the arrow direction Cleaning the Full HD filterRemove dust with a vacuum cleaner or running water Full HD filter filters the big dust of incoming airCleaning the Zero filter Troubleshooting Odors permeate Conditioner isWater is Heard when refrigerant flow movement changes. It is normalOpen Source Announcement Installation parts English Required tools General toolsTools for test operations Outdoor unit Choosing the installation locationIndoor/outdoor unit installation diagram Installation space for floor type indoor unitPiping length for indoor/outdoor unit installation Outdoor unit Fixing outdoor unitSea breeze Installation accessories AccessoriesIndoor unit accessories Outdoor unit accessoriesFfDrill a hole with diameter of 60~65mm towards the outside Connecting pipesInstallation procedure Drilling a hole and fixing the indoor unitFfFlare process FfFlare lengthFfIncorrectly flared pipes FfTightening of connection parts FfPipe insulationIndoor Use finishing tape wind up the refrigerant pipe Connecting drain hose Connection with wire-concealed pipingFix the drain hose tightly to prevent any water leakage Wiring standard Connecting procedureElectrical work Type of outdoor unit power supply Safety information on outdoor unit power supplyFfItems to prepare How to connect your extended power cablesApply heat to the contraction tube to contract it Vacuuming pipe Vacuum pumpNm = 10 kgfcm Test part for indoor unitInstalling the earth wire Charging refrigerantCharge the refrigerant depending on the pipe length Display the temperature of indoor heat exchanger Check and test operationDisconnect the pipe
Related manuals
Manual 54 pages 30.56 Kb