Samsung AF55GP1MBEENMG manual Preparing the installation, Unit for exhausted air to ventilate

Page 31

Preparing the installation

Selecting appropriate location for installation

Decide the installation location based on the following condition and obtain the user’s approval.

ffAvoid a place that may disturb your neighbor. Noise may occur from the outdoor unit and the discharged air may run into the neighborhood. (Be careful of the operation time in a residential area)

ffInstall the outdoor unit on a hard and even area that can support its weight. ffChoose a flat place that rainwater does not settle or leak.

ffChoose a place avoiding strong winds.

ffMaintain sufficient space for repairs and service.

ffChoose a place where you can easily connect the pipes and cables to the indoor unit.

ffMake sure that the condensed water dripping from the drain hose runs out properly and safely.

ffWhen installing the outdoor unit near seashore, make sure it is not directly exposed to sea breeze. If you can not find a adequate place without direct see breeze, protection wall should be constructed.

ffInstall the outdoor unit in a place (such as near buildings etc.) where it can be prevented from sea breeze which can damage the outdoor unit.

Outdoor unit

Sea breeze

Sea breeze

Outdoor unit

Sea

 

Sea

 

 

 

fIfyou cannot avoid installing the outdoor unit by the seashore, construct a protection wall around to block the sea breeze.

Protection wall

Sea breeze

Sea

Outdoor unit

• Protection wall should be constructed with a solid material such as

 

concrete to block the sea breeze and the height and the width of the

 

wall should be 1.5 times larger than the size of the outdoor unit. Also,

 

secure over 700 mm between the protection wall and the outdoor

 

unit for exhausted air to ventilate.

ffInstall the outdoor unit in a place where water can drain smoothly.

❋❋If you cannot find a place satisfying above conditions, please contact manufacturer. Make sure to clean the sea water and the dust on the outdoor unit heat exchanger and spread corrosion inhibitor on heat exchanger. (At least one time per one year.)

ffChoose a place where there is no direct sunlight.

ffChoose a place where it could not come into contact with snow and rain. ffChoose a place where flammable gas does not leak.

ffChoose a place where the indoor and outdoor unit can be connected with a pipe.

32

PAC MIRAGE HPCO-AR-PH_IBIM_05321A-01_EN.indd 32

2015-03-03 오후 4:39:39

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Strong Turbo/Long Function Features of your new air conditionerLook for Everywhere Contents Important safety symbols and precautions Safety precautionsDo not yank the power cable with hands Severe Warning Signs Do not open the front panel during operation Use a rated circuit breaker onlyFfPotential risk of injury or electric shock FfPotential risk of personal injuryFfInsufficient ventilation may result in poor performance Do not allow children to climb on the air conditionerFfPotential risk of personal injury or property loss FfWearing thick gloves can protect your hands To open the panel Checking the name of the partsChecking the indoor unit and display Main partsHeater and Purity functions are not supported by this model Control panelRemote controller buttons Checking the remote controllerUsing the remote controller Remote controller displayLamps are in the same space Indoor unit Battery changing timeStoring the remote controller Inserting the batteriesBasic operation Selecting the fan speed Turning on the powerSelecting the operation mode Adjusting the desired temperatureSelecting air flow direction Additional options available in On timer Setting the On/Off timerWhen the air conditioner is off You cannot set the fan speed when setting the On timerBe different from each other When the air conditioner is onUsing the Long function Using the Turbo functionWhen the air conditioner is operating in Cool or Heat mode Locking the control panel FfYou can increase/decrease the temperature by 1 C Button to adjust the temperatureButton to adjust the fan speed Cleaning the exterior Cleaning and maintaining the air conditionerCleaning the filter Air filter Periodical checks Maintaining your air conditionerType Description Internal protections via the unit control system Have deposited at low temperaturesOutdoor unit after it has been started Appendix TroubleshootingHumidity Operation rangesAccessing its internal components Installing the unitGeneral information Complete, electric shock or fire may occur Power supply line, fuse or circuit breakerDo not install the air conditioner in following places Make sure that you earth the cablesPart Name Accessory parts listSide view Selection of installation placeIndoor unit Top viewOutdoor unit Selecting appropriate location for installation Preparing the installationUnit for exhausted air to ventilate Wear protective goggles and mask before spraying Space requirementsElectrical work Wiring standardCord. Code designation IEC60245 IEC 66 / CENELECH07RN-F AP55M1 Series Indoor and outdoor connection wiringUsing 3poles ELCBEarth Leakage Circuit Breaker AP55M0 SeriesUsing 3poles Elcb and 2poles Elcb Using 4poles ELCBEarth Leakage Circuit BreakerAP55M2 Series AF55GC1M Series Using 2poles ELCBEarth Leakage Circuit BreakerAF55GP1M Series Connecting the power terminal Electrical wiringScrew Tightening torque kgf·cm Put the rubber leg to the outdoor unit leg Installation methodOutdoor unit When using the anchor bolt When using the rubber legInstallation procedures When Wiring FfHeight of the oil trap H 4R ≤ H ≤ 6R Check the following list and install an oil trapRefrigerant pipe work Insulating the pipes Oil trapIt may cause explosion and injury Cut the pipe using the pipe cutterConnection of refrigerant piping Flare processing Remove burr on the edge of pipeOuter diameter mm Tightening torque kgf·cm Pipe bendingTightening of connection parts Drilling a hole in the wallExample Wall installation Corner InstallationDrain hose Fixing the indoor unitBe sure that all valve cocks are closed Air purgeAP55M0AN AF55GC1M N AF55GP1M N FfCooling operations How to add refrigerantPressure table for temperatures Refrigerant chargingCheck Check and test operationIs grounding properly made? When the outdoor temperature is below zero, do not Pump down procedure When removing the productTest operation Packing and unpacking guide Outdoor unit To finish How to connect your extended power cablesModel Product specificationQuestions or COMMENTS? Thank you for purchasing this Samsung product Air Conditioner
Related manuals
Manual 54 pages 8.23 Kb

AP55M0ANUMG, AF55GP1MBEENMG, AP55M2ANUMG, AF55GC1MBEENMG, AF55GC1MAEENMG specifications

Samsung has established a reputation for innovation in the realm of technology, particularly with its display solutions. Among its latest offerings in the market are the AP55M0AXUMG, AP55M0BNUMG, AP55M1ANUMG, AF55GC1MAEENMG, and AF55GC1MBEENMG models. These displays cater to various commercial applications, boasting impressive specifications and cutting-edge technologies that enhance user experiences.

The AP55M0AXUMG and AP55M0BNUMG are part of Samsung's premium range, featuring a stunning 55-inch display that utilizes advanced LED technology for vibrant colors and remarkable clarity. Both models support 4K resolution, ensuring that images are sharp and lifelike, which is particularly beneficial for presentations, advertising, and other commercial uses. With an ultra-narrow bezel, these displays maximize the viewing area while maintaining a sleek profile that seamlessly blends into any environment.

Equipped with powerful processors, these displays support seamless multitasking capabilities and real-time content sharing. Their compatibility with various content management systems allows users to create dynamic displays for effective engagement with their audience. The built-in Wi-Fi capabilities ensure easy connectivity, making it simple for users to update content remotely.

The AP55M1ANUMG model takes things a step further by incorporating Samsung's MagicINFO solution, which enables users to manage, schedule, and control multiple screens from a single interface. This feature is particularly advantageous for businesses that require coordinated messaging across multiple locations. Additionally, this model boasts enhanced brightness and contrast ratios, ensuring visibility even in well-lit environments.

On the other hand, the AF55GC1MAEENMG and AF55GC1MBEENMG displays cater to those seeking high-quality performance along with advanced interactive capabilities. Both models employ Samsung's innovative touch technology, allowing users to interact directly with the content displayed. This makes them ideal for educational and collaborative settings, where engagement and interactivity are paramount.

Furthermore, these displays are designed with durability in mind, featuring a robust construction that can withstand various environmental conditions. The energy-efficient design ensures lower operational costs, making them a sustainable choice for businesses looking to reduce their carbon footprint while still delivering high-impact visual experiences.

In conclusion, Samsung's AP55M0AXUMG, AP55M0BNUMG, AP55M1ANUMG, AF55GC1MAEENMG, and AF55GC1MBEENMG models are at the forefront of display technology, providing businesses and educational institutions with the tools they need to communicate effectively and capture audience attention. Their advanced features, combined with Samsung's legacy of quality, make these displays a sagacious investment for any organization seeking to elevate its digital presentation capabilities.
Top Page Image Contents