Samsung AR12FSFPKGMNZE manual Fixing the indoor unit in place, Fixing the outdoor unit in place

Page 42

Fixing the indoor unit in place

Perform the following work on the area where gas leak test was done priorly.

After checking for gas leaks in the system, insulate the pipe, hose and cables.

Insulation

Then place the indoor unit on the installation plate.

 

1. To avoid condensation problems, wrap foam insulation (as shown in the figure) on a part without insulation on the end of the pipes.

Pipes

2.Wind the pipe, assembly cable and drain hose with vinyl tape.

3.Place the bundle (the pipe, assembly cable and drain hose) in the lower part of the indoor unit carefully so it does not project from the rear of the indoor unit.

4.Hook the indoor unit to the installation plate and move the unit to the right and left until it is securely in place.

Installation

 

plate

Connecting

Vinyl tape

pipes

Connecting wires

 

Drain hose

 

• Make sure pipe does not move when you install the indoor unit on an installation plate.

5.Wrap the rest of the pipe with vinyl tape.

6.Attach the pipe to the wall using clamps (optional).

Fixing the outdoor unit in place

Install the outdoor unit in level on a stable base to avoid the generation of noise and vibration, especially when installing the unit close to a neighbor.

If you install the outdoor unit in a place exposed to strong winds or at a height, fix it to an appropriate support (wall or ground).

'X' mm

'Y' mm

1.Place the outdoor unit as indicated on the top of the unit to let the discharged air out properly.

2.Fix the outdoor unit in level to an appropriate support using anchor bolts.

3.If the outdoor unit is exposed to strong winds, install shield plates around the outdoor unit so that the fan can operate correctly.

• Secure the rubber leg to prevent the generation of noise and vibration.

Rubber leg

Model

X

Y

AR09/12GGM

538

290

AR09/12DGM

612

317

AR09/12KGM

 

 

AR18/24FSFP

660

340

Outdoor unit installed on the wall by rack

•Ensure the wall will be able to suspend the weight of rack and outdoor unit;

•Install the rack close to the column as much as possible;

•Install proper grommet in order to reduce noise and residual vibration transferred by outdoor unit towards wall.

Designed to cut off residual vibration from outdoor unit to rack.

(not supplied with product)

Soft rubber designed to cut off vibration from rack to wall. (not supplied with product)

42

Maldives ZE_AR09FSFP@_IBIM_DB68-03379A_EN.indd 42

2012-12-8 9:09:10

Page 41 Page 43
Image 42
Page 41 Page 43
Contents Maldives ZEAR09FSFP@IBIMDB68-03379AEN.indd 2012-12-8 Contents Personal injury or death Safety precautionsImportant safety symbols and precautions Personal injury or property damageFor Installation Caution For Using Do not touch the circuit breaker with wet hands Do not place objects or devices under the indoor unit Do not operate the appliance with wet hands Do not drink the water from the air conditionerDo not touch the pipes connected with the product For Cleaning Do not clean the inside of the air conditioner by yourselfChecking before use Operation rangesModel AJ Main parts Power buttonChecking the name of the parts DisplayChecking the remote controller Remote controller buttonsStoring the remote controller Remote controller displayBattery changing time Inserting the batteriesBasic function Button to adjust the temperature PressPress the Air swing button on the remote controller Adjusting the air flow directionUsing the Turbo function Vertical air flowMode When the air conditioner is on and in cool/heat modePress the button on the remote controller Press the Time Up or Time Down button to set the timeCancel Press the Cancel button Setting the On/Off timerPress the On Timer/Off Timer button Additional options available in On timer modeIf the air conditioner is on If the air conditioner is off Using the Smart Saver functionFrom the moment you have set the timer Turn off automaticallyWhen the air conditioner is turned on Using the Quiet functionUsing the Auto Clean function You can reduce the noise generated from an indoor unitCleaning the indoor unit Cleaning the air conditionerMake sure the power is turned off and unplugged from Cleaning the outdoor unit heat exchangerOpen the panel and put the Air filter out Cleaning the air filterRemoving the Air filter Dry the Air filter in a ventilated areaClean the condensate drain pan Maintaining the air conditionerTroubleshooting Does not set After you have set the time Indicator Working Cannot adjust the temperature Fan speedTimer function Service centerGeneral information Included Models RemarkPower supply line, fuse or circuit breaker Choosing the installation locationInstalling the unit  a place where the air filter can be replaced easilyWhere sulfide gas exists Outdoor Unit Figure Description When installing more than 1 outdoor unitWhen the air outlet is towards the wall Top view Side viewAccessories Accessories in the indoor unit caseAccessories in the outdoor unit case Tools required for installation General Tools Fixing the installation plateOptional accessories Tools for test operationsConnecting the assembly cable Cable specificationConnecting the cable Extend the assembly cable if necessary Each wire is labeled with the corresponding terminal numberSmooth the cut edges Cut off the remaining foam insulationUnscrew the caps at the end of each pipe Purging the indoor unitCutting or extending the pipe Put a flare nut slightly into the pipe and modify the flareCracked Pipe 50 Pa. The joint must be accessible and serviceableCorrect Inclined Outer DiameterDrain hose installation Changing direction of the drain hosePurging the connected pipes Connect a drain hose to the drain plugEnsure that condensation draining is adequate If you use a pipe shorter than 5m Adding RefrigerantIf you use a pipe longer than 5m ModelPlease fill in with indelible ink  the factory refrigerant charge of the product1975 To check for gas leaks on the indoor unit Performing the gas leak testsTo check for gas leaks on the outdoor unit Leak test with nitrogen before opening valvesThen place the indoor unit on the installation plate Fixing the indoor unit in placeFixing the outdoor unit in place Final Check and Trial Operation After tube contraction work is completed, wrap it with How to connect your extended power cablesApply heat to the contraction tube to contract it Insulation tape to finishOnly for multi system Sub PCB installationoptionalWried remote controller, central remote controller etc Assemble the Cover PCB and the front panelQuestions or COMMENTS? Air Conditioner
Related manuals
Manual 46 pages 39.71 Kb Manual 45 pages 27.27 Kb Manual 1 pages 30.76 Kb Manual 45 pages 23.86 Kb Manual 1 pages 26.59 Kb Manual 1 pages 28.23 Kb Manual 45 pages 14.41 Kb Manual 45 pages 15.07 Kb Manual 45 pages 25.41 Kb

AR09FSFPKGMNZE, AR12FSFPKGMNZE, AR09FSFPKGMNET, AR12FSFPKGMNET specifications

The Samsung AR12FSFPKGMNET, AR12FSFPKGMXZE, AR12FSFPKGMNZE, and AR12FSFPKGMXET are part of Samsung's cutting-edge line of air conditioners designed to offer efficient cooling and heating solutions for modern living spaces. These models are well-known for their innovative technologies, sleek designs, and energy-efficient performance, making them ideal for residential and commercial applications.

One of the standout features of these units is the Digital Inverter technology, which significantly reduces energy consumption compared to conventional models. By adjusting the compressor speed according to the cooling demand, the Digital Inverter maintains a consistent temperature while minimizing energy use, leading to lower utility bills. This technology also helps in reducing noise levels, providing you with a peaceful indoor environment.

In addition to energy efficiency, these air conditioners incorporate Samsung's unique Tri-Care Filter system. This advanced filtration technology effectively removes dust, allergens, and harmful particles from the indoor air, ensuring a healthier living space. The filters are easy to clean and can be accessed conveniently, promoting better maintenance practices.

Another important characteristic of the Samsung AR series is the Fast Cooling mode. This function allows the air conditioner to rapidly cool the room during hot weather, providing swift relief from heat. The powerful mode is particularly beneficial during the sweltering summer months when immediate cooling is essential.

The Smart Control feature is another significant innovation found in these models. Users can effortlessly control their air conditioners through a smartphone app, providing convenience and flexibility. With Smart Control, you can adjust temperatures, set timers, and monitor energy consumption from anywhere, making it easy to manage your indoor climate remotely.

Additionally, the design of the AR12FSFPKGMNET, AR12FSFPKGMXZE, AR12FSFPKGMNZE, and AR12FSFPKGMXET models is sleek and modern, allowing them to blend seamlessly into any interior decor. The compact size and subtle styling ensure a good fit for various room sizes, enhancing the aesthetic of the space while providing outstanding performance.

In conclusion, the Samsung AR12FSFPKGMNET, AR12FSFPKGMXZE, AR12FSFPKGMNZE, and AR12FSFPKGMXET air conditioners embody a perfect blend of advanced technology, energy efficiency, and user-friendly features, making them a top choice for consumers seeking reliable and stylish cooling solutions.
Top Page Image Contents