Samsung LC49J890DKIXCI, LC49J890DKUXEN manual Removing the Stand For Attaching the Bracket Wall

Page 21

Removing the Stand (For Attaching the BRACKET WALL)

――Before removing the stand from the monitor, place the monitor on a flat and stable surface with the screen facing down.

: The product is curved. Placing pressure on the product when on a flat surface may damage the product. When the product is on the ground facing up or down, do not put pressure on it.

Rotate the COVER-REAR TOP counterclockwise.	Lift the COVER-REAR TOP.	Disassemble the COVER-REAR TOP.	Remove the stand base from the stand neck.
5	6

Unfasten the 4 screws at the top of the stand neck. Lift and remove the stand.

Caution

Do not press down on the monitor. There is a risk of damaging the monitor.

Image 21

Contents C49J890DK Table of contents PIP/PBP Securing the Installation Space Before Using the ProductSafety Precautions Precautions for storageElectricity and Safety CleaningWipe the monitor with a clean, soft and dry cloth Power on the product and computerInstallation Operation Page Preparations PartsControl Panel Adjust Volume This LED is power status indicator and works asDirect Key guide Display Function Key GuideReturn Function Key GuideExit the Main menu Move the optionClose Sublist without saving value Value decreases in the sliderChanging the Volume setting Changing Brightness, Contrast and Eye Saver Mode settingsPortDescription Types of PortsSoftware upgrading proceeds Upgrading the Software via USBCopied to the root directory Make sure only the BIN file for upgrade is in the USB disk+4˚ Adjusting the Product Tilt and HeightTo lock an anti-theft locking device Anti-theft LockAttaching the Stand Type one InstallationAttaching the Stand Type two Place the stand neck on the monitor asNeck in the direction as shown Remove the package Lift the COVER-REAR TOP Disassemble the COVER-REAR TOP Removing the Stand For Attaching the Bracket WallAttach the Bracket Wall here Attaching the Bracket WallRead below before installing the monitor Connecting and Using a Source DeviceConnecting and Using a Source Device Connection Using the Hdmi CableConnection Using the USB Type-C Cable Connection Using the DP CableConnecting the Product to a Source Device as a USB Hub Connecting to HeadphonesConnecting a Source Device to the Product Utilizing the Product as a USB HUB Power Connecting the PowerHeadphones hanger Downward Upward Tidying Up the Connected CablesArrange the cables against the bend Driver Installation Setting Optimum ResolutionCorrect posture to use the product Picture Samsung Magic BrightYou can customize the brightness to suit your preferences Contrast BrightnessSharpness ColorEye Saver Mode Samsung Magic UpscaleHdmi Black Level Picture Size Screen AdjustmentCalibration Report Change the picture sizeEnable or disable the PIP/PBP Mode function PIP/PBP ModeAspect Ratio SizePosition Sound SourceSelect the source for each screen SourceMonitor Switch USBMobile Phone LaptopSet the Picture Size for each of the divided screens Select the image size for sub-screenAdjust the contrast level for each screen Adjust the contrast level for sub-screenTransparency OnScreen DisplayLanguage Display TimeHdmi Mode USB Source SetupSystem DisplayPort VerPC/AV Mode Off Timer PlusSmart ECO Saving Off Deactivate the Smart ECO Saving functionReset All Power LED OnSource Detection InformationEasy Setting Box Installing the SoftwareRestrictions and Problems with the Installation System RequirementsTesting the Product Troubleshooting GuideChecking the Resolution and Frequency Check that the power cable is connected properlyCheck the cable connection to the product Change the Color settingsUniversal Serial Bus USB issue Set the frequency on your graphics card General SpecificationsStandard Signal Mode Table 60.000 108.000 +/+ 106.50060.000 148.500 +/+ 266.500Product damage caused by customers fault Responsibility for the Pay Service Cost to CustomersAppendix Not a product defectExtended warranty

Related manuals

Manual 53 pages 49.45 Kb

Manual 53 pages 47.65 Kb

Manual 52 pages 10.39 Kb

Removing the Stand (For Attaching the BRACKET WALL)

Lift the COVER-REAR TOP.

Disassemble the COVER-REAR TOP.