Crestron electronic GLPS-HSW, IPAC-GL1, GLPS-SW-FT manual Gls-Pls, 120/277 Power Loss Sensor

Page 33

Crestron Commercial Lighting Design Guide

Green Light Power Switching

GLS-PLS-

120/277 Power Loss Sensor

The GLS-PLS-120/277 is a 3-Phase Power Loss Sensor designed for use with Crestron Green Light™ systems to activate Override mode during a power failure. In response to a signal from the GLS-PLS-120/277, the lighting system program can be temporarily overridden while designated emergency lighting circuits are changed to their override preset levels and unnecessary lighting and other devices are shut down to minimize the demand on emergency power equipment.

The GLS-PLS-120/277 senses each leg of a 120 or 277 volt 3-phase feed, providing LED indication of the status of each phase on its front panel. When power is lost on any phase, the corresponding status LED turns off and a contact closure is activated on each of two control outputs. Two isolated control outputs are provided to allow for interfacing with third-party equipment in addition to the Crestron lighting system. Each contact closure output is rated for 1A @ 24VDC.

Testing the GLS-PLS-120/277 is facilitated using three test switches located behind a small cover plate on the front of the unit. Setting any switch to the TEST position simulates a loss of power on the corresponding phase leg, providing a test of the units’ internal circuitry and any connected equipment.

The steel enclosure is designed for mounting to a vertical surface. Conduit knockouts are provided on the bottom, top, and both sides. All electrical connections are made via screw terminals accessed by removing the front panel.

Senses loss of power on each leg of a 3-phase feed

Used to satisfy UL 924 (Emergency Power Equipment) requirements

Works with 120 or 277 Volt feeds

Designed to activate the Override mode on Crestron lighting modules

Provides two isolated contact closure outputs

Each output rated 1A @ 24VDC

Includes built-in test function for each phase input

Surface mount enclosure includes conduit knockouts

SPECIFICATIONS

Input Voltages

277V Voltage Range: 235 to 305 Volts AC, 50/60 Hz

120V Voltage Range: 102 to 132 Volts AC, 50/60 Hz

Connections

PHASE A, B, C: (3) Main feed sensing inputs, 277 or 120 Volts

OUTPUTS: (2) Form ‘A’ contact closures, electrically isolated. Both outputs close when main feed power is removed from any phase sensing input. Rated 1 Amp @ 24 Volts DC

Indicators & Controls

NORMAL A, B, C: (3) Green LEDs, each illuminates when corresponding test switch is

set to NORMAL and power is present at corresponding phase sensing input TEST A, B, C: (3) Red LEDs, each illuminates when corresponding test switch is set to TEST and power is present at corresponding phase sensing input

Test Switches: (3) Slide switches behind cover plate, used to set each corresponding phase sensing input to TEST mode

Enclosure

Galvanized steel with polycarbonate label overlay; surface mount with integral mounting flanges top and bottom; 3/4” & 1/2" conduit knockouts top, bottom, and both sides

Environmental

Temperature: 32° to 104°F (0° to 40°C)

Humidity: 10% to 90% RH (non-condensing)

Heat Dissipation: 51 BTU/Hr

Dimensions

Height: 12.69 x 5.19 x 2.82 in (32.23 x 12.75 x 7.14 cm) HWD

Weight

3.7 lb (1.7 kg)

Doc 4775A

29

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Crestron Green Light Commercial Lighting Design Guide Page Contents Page Introduction Crestron Green LightOr any other Crestron software Single Solution Control System- Crestron Exclusive Crestron Control TechnologyOr automatic load shedding System Design Lighting System Design Types Wireless SystemsCentralized Wired Systems System Design Crestron Commercial l Lighting Design Guide Decentralized Wired SystemsHybrid Systems Specifying a Lighting System Required Load Schedule ItemsLoad Schedule Example Load Schedule with Panel Terminations Complete diagram is available on line atEquipment List Specification Commercial Lighting Wiring PlanOrdering a Crestron Commercial Lighting System Steps to order a lighting systemSystem Features Green Light Power SwitchingCan be programmed without ever having to connect a computer Green Light Power Switching GLPS-HSW-MLO-30-120-10K -ND FrontMCB100 Main lug onlyMCB125 Available for 277V onlySpecifications Glps SW MLO 30 120 10K ND 100125 GLPS-SW-MLO Large 78-15/16 x 20-1/4 x 6-5/8 in 200.5 x 51.4 x 16.8 cm Medium 70 x 20-1/4 x 6-5/8 in 177.8 x 51.4 x 16.8 cmModel Numbers GLPS-HSW-FT GLPS-SW-FTGreen Light Express Feed Specifications Load Ratings Small 8, 16 Large 32, 40, 48 Glps Hdsw FT Glps Relay Type Feed Type Number of CktsLoad Ratings GLPS-HDSW-FTDoc.4775A Ethernet Sdram 32 MB Nvram 1 MBGLA-PWS50 Wall Mount 50 Watt Cresnet Power SupplyGLS-PLS 120/277 Power Loss SensorDimensions Dimensions GLEP-HSW & GLEP-SW Large Panel GLEP-HSW & GLEP-SW Extra Large Panel GLEP-HSW-FT, GLEP-SW-FT, & GLEP-HDSW-FT Panels IPAC-GL1 CAEN- Series Enclosures Green Light OptionsCrestron Commercial Lighting Design Guide Caen Enclosures SpecificationsCaen Enclosure Framing Caen InstallationCaen 2X1, 4X1, and 7X1 Framing Caen 4X2 FramingCaen Wiring Universal Mounting Plates Cover Extension Kits Dimensions are provided in inchesCLX Lighting Control Modules Model Load Rating CLX-Series Lighting Control ModulesTerminal Blocks and Modules Single Width Enclosure Mounting Module InstallationCresnet Terminal Block for Caen Automation Enclosures Green Light Options-CAEN Enclosures Features DIN Rail InstallationCrestron DIN Rail Products Example DIN Rail System DIN-AP2 DIN-1DIMU4 Phase-Synchronous Detection CircuitryAuto Load Detection Short Circuit ProtectionDIN-8SW8 DIN-4DIMFLV4DIN-2MC2 DIN-IO8 DIN-AO8Analog Outputs VersiportsDIN-BLOCK Cresnet Power DistributionDIN-PWS50 Cresnet Distribution 3-segment Cresnet hub  32 Cresnet devices per segment DIN-HUBInterface Equipment TPS Series Isys Wall Mount TouchpanelsTPS Isys G-Series with Crestron Home or QuickMedia Tpmc Isys I/O with Crestron Home or QuickMediaTPS-4000L TPMC-8LTPS-4L TPS-4000 Tilt TouchpanelsTPMC-8T Tpmc Series Isys i/O WiFi TouchpanelsTPMC-8X TPMC-4XGTPS-6X Wireless Touchpanels and HandheldsMT-1000C ML-600Keypads C2N-DB Series Decorator KeypadsC2N-DB Mounting  Each keypad requires 3 watts of power CNX Designer Series KeypadsMounting in Single-Gang Box Cameo Cameo Mounting Options Cameo Flush Mount Mud Ring Mount KitDo not use the C2N-CB with the decorator-style keypads ILux Integrated Lighting Control System ILux Features Wireless iLux Remote Multi-Unit Expansion Stand-alone Master with Slave wiringControl System Integration ILux Expansion Modules Supports 3-wire Fluorescent Fluorescent DimmingModel Load Function Supports incandescent, magnetic low voltageExpansion Modules Wiring Diagrams Wall Box Dimmers and Switches Cresnet Wall Box Dimmers Model Load FeaturesCLW-SLVS Cresnet Wall Box SwitchesInfiNET Wireless Technology InfiNET Dimmers, Switches, and Thermostat Example infiNET system PAC2 Lighting Control Processor Control ProcessorsPAC2 Power Management & Requirements Series Control System PAC2M Professional Automation Mini Control SystemOverride Basic Lighting System Interconnections Occupancy and Photocell Sensors C2N-SDC Integrated Shade and Drape ControllersC2N-SDC-DC C2N-SSC-2Integrated Systems Integrated Partner ModulesRoomView Server Edition Appendix a RoomView Remote Asset Management Tracking of projector lamp life in bar graph format Appendix aExample RoomView Server Edition reports RoomView Express Green Light Designer Software Appendix BAppendix B Appendix C Touchpanel Comparison Charts Crestron Commercial Lighting Design GuideAppendix C Commercial Lighting Design Guide Wireless Touchpanels & Handheld RemotesStatic and Dynamic Elements Appendix D General Lighting Design ConsiderationsSimple Lighting Coverage Areas Task Lighting for Specific Work AreasDecorative Lighting Ambient Lighting for Mood and HighlightsFocal Lighting Key LightColor Temperature Switch and Dimmer LocationsGrazing and Washing Surfaces Color RenditionAppendix E Glossary of Lighting Terminology Appendix E Commercial Lighting Design Guide Appendix E Doc 4775A 101 Doc 4775A 102

GLPS-HSW-FT, GLPS-HDSW-FT, GLPS-HSW, GLPS-SW-FT, GLPS-SW specifications

Crestron is a leading company in the field of automation and control technology, and their range of products continues to empower users with innovative solutions for audio-visual management and building control. Among their offerings, the GLPS-SW-FT, GLPS-HDSW-FT, GLPS-SW, GLPS-HSW, and IPAC-GL1 stand out with distinct features and capabilities designed to enhance user experiences in various environments.

The Crestron GLPS-SW-FT is a powerful presentation switcher that facilitates seamless connectivity with multiple input sources, enabling users to consolidate their AV equipment efficiently. With support for multiple resolutions and formats, this device is equipped with advanced processing capabilities, ensuring high-quality video output. Its intuitive interface simplifies operations, allowing users to switch between presentations effortlessly.

The GLPS-HDSW-FT, on the other hand, is a high-definition switcher designed specifically for HDMI connections. This model offers comprehensive support for HDCP compliance and deep color, guaranteeing optimal visual quality during presentations. Furthermore, it features built-in scaling technology, allowing for flexible display configurations that cater to various screen sizes and resolutions.

The Crestron GLPS-SW is engineered to enhance user interaction with its advanced control systems. This device integrates seamlessly with Crestron's ecosystem, providing extensive programming options that allow customization according to specific requirements. Its ability to interface with touch panels and other control devices makes it a versatile solution in corporate settings and educational institutions.

In contrast, the GLPS-HSW is recognized for its robust switching capabilities that manage HDMI, audio, and other video formats simultaneously. This device is particularly suited for complex installations where multiple sources are used. It offers remote management capabilities, enabling system integrators to monitor and control the device effectively.

Lastly, the IPAC-GL1 is a groundbreaking control interface that amalgamates user-friendly design with powerful functionality. This model provides tactile feedback and customizable buttons for precise control over AV systems. Its compact form factor makes it easy to integrate into any workspace, promoting an efficient workflow.

Collectively, these Crestron products represent a commitment to quality and innovation in the realm of AV control and management. They leverage advanced technologies and user-centric designs to meet the evolving demands of modern environments, reaching new heights in interoperability, efficiency, and ease of use. Whether for corporate presentations, educational applications, or entertainment venues, Crestron’s GLPS and IPAC offerings are tailored to provide exceptional performance and reliability.
Top Page Image Contents