Crestron electronic GLPS-HSW-FT, IPAC-GL1, GLPS-SW-FT manual PAC2 Power Management & Requirements

Page 83

Crestron Commercial Lighting Design Guide

Control Processors

The Fault connector provides a dry contact closure fault signal to notify an external control system when the PAC2 has a system fault. This output is connected to a digital input of the backup computer. A fault is defined as the CPU not interacting with Cresnet® for 10 seconds. The watchdog switches back if the backup computer is inactive for 10 seconds.

The PAC2 offers eight programmable analog and digital inputs as well as digital outputs. There are eight normally open relays, isolated with MOV suppression.

PAC2 Power Management & Requirements

When power requirements exceed 50 watts, additional power supplies may be added. For example, each keypad in the CNX-B series uses 3 watts, therefore only 15 keypads (allowing for a margin of safety) can be connected without adding an additional power supply.

To ensure sufficient power to accommodate all the Cresnet devices (keypads, touchpanels, shade/drape controllers, thermostats, sensors, and other interfaces) and to include voltage drops and wire runs, Crestron recommends the CLX-PWS75 75-watt Cresnet power supply module, or the C2N-SPWS300 300-watt system power supply.

The 75-watt power supply is designed to mount in a CAEN Automation Enclosure. A single CLX-PWS75 can

be installed in any single-width enclosure, or up to two may be installed side-by-side in a double-width enclosure. Four (4) Cresnet power ports are provided on the CLX-PWS75, which may be used to supply power directly to Cresnet devices, or connect to the external power input ports of a PAC2 or PAC2M.

If the power needed for a hub segment exceeds the power available from the internal supply (50 watts, maximum), remove the jumper from the supplied 3-pin mini connector to disconnect the internal power supply, then connect the 24VDC and ground wires from an external source (Crestron 24 VDC - regulated power supply) to the EXT and G pins.

The 300-watt power supply, specifically designed for large Cresnet control systems, operates with an input of

100 to 240 VAC, 4A (maximum) and a noise rating less than 150mV. The C2N-SPWS300 provides regulated 24 VDC, 300-watts to Cresnet system components. The C2N- SPWS300 is capable of delivering a nominal 75 watts of power at 24 volts DC on any of its eight channels.

The CLX-PWS75 is a 75 watt Cresnet Power Supply Module designed to mount in a CAEN Automation Enclosure. A single CLX-PWS75 can be installed in any single-width enclosure, or up to two may be installed side-by-side in a double-width enclosure. Four (4) Cresnet power ports are provided on the CLX-PWS75, which may be used to supply power directly to Cresnet devices, or connect to the external power input ports of a PAC2 or PAC2M.

Additional power supplies should not be mounted on CAEN-UMP plates in an enclosure that contains dimmer units because this introduces low voltage in the high voltage section of the enclosure. If required, an extra power supply, attached to a CAEN-UMP plate, can be added to a separate CAEN enclosure.

Mounting the PAC2 in a double-wide enclosure

Refer to the PAC2 Operations Guide (Doc. 5941) for more detailed information.

Doc 4775A

79

Page 82 Page 84
Image 83
Page 82 Page 84
Contents Crestron Green Light Commercial Lighting Design Guide Page Contents Page Or any other Crestron software IntroductionCrestron Green Light Or automatic load shedding Single Solution Control System- Crestron ExclusiveCrestron Control Technology System Design Lighting System Design Types Wireless SystemsCentralized Wired Systems System Design Crestron Commercial l Lighting Design Guide Decentralized Wired SystemsHybrid Systems Load Schedule Specifying a Lighting SystemRequired Load Schedule Items Example Load Schedule with Panel Terminations Complete diagram is available on line atSteps to order a lighting system Commercial Lighting Wiring PlanEquipment List Specification Ordering a Crestron Commercial Lighting SystemSystem Features Green Light Power SwitchingCan be programmed without ever having to connect a computer Green Light Power Switching GLPS-HSW-MLO-30-120-10K -ND FrontAvailable for 277V only Main lug onlyMCB100 MCB125Specifications 125 Glps SW MLO 30 120 10K ND100 GLPS-SW-MLO Large 78-15/16 x 20-1/4 x 6-5/8 in 200.5 x 51.4 x 16.8 cm Medium 70 x 20-1/4 x 6-5/8 in 177.8 x 51.4 x 16.8 cmModel Numbers GLPS-HSW-FT GLPS-SW-FTGreen Light Express Feed Specifications Load Ratings Small 8, 16 Large 32, 40, 48 Glps Hdsw FT Glps Relay Type Feed Type Number of CktsLoad Ratings GLPS-HDSW-FTDoc.4775A Ethernet Sdram 32 MB Nvram 1 MBGLA-PWS50 Wall Mount 50 Watt Cresnet Power SupplyGLS-PLS 120/277 Power Loss SensorDimensions Dimensions GLEP-HSW & GLEP-SW Large Panel GLEP-HSW & GLEP-SW Extra Large Panel GLEP-HSW-FT, GLEP-SW-FT, & GLEP-HDSW-FT Panels IPAC-GL1 CAEN- Series Enclosures Green Light OptionsCrestron Commercial Lighting Design Guide Caen Enclosures SpecificationsCaen 4X2 Framing Caen InstallationCaen Enclosure Framing Caen 2X1, 4X1, and 7X1 FramingCaen Wiring Universal Mounting Plates Cover Extension Kits Dimensions are provided in inchesCLX Lighting Control Modules Model Load Rating CLX-Series Lighting Control ModulesTerminal Blocks and Modules Single Width Enclosure Mounting Module InstallationCresnet Terminal Block for Caen Automation Enclosures Green Light Options-CAEN Enclosures Crestron DIN Rail Products FeaturesDIN Rail Installation Example DIN Rail System DIN-AP2 Short Circuit Protection Phase-Synchronous Detection CircuitryDIN-1DIMU4 Auto Load DetectionDIN-2MC2 DIN-8SW8DIN-4DIMFLV4 Versiports DIN-AO8DIN-IO8 Analog OutputsCresnet Distribution Cresnet Power DistributionDIN-BLOCK DIN-PWS50 3-segment Cresnet hub  32 Cresnet devices per segment DIN-HUBInterface Equipment Tpmc Isys I/O with Crestron Home or QuickMedia Wall Mount TouchpanelsTPS Series Isys TPS Isys G-Series with Crestron Home or QuickMediaTPS-4L TPS-4000LTPMC-8L TPS-4000 Tilt TouchpanelsTPMC-4XG Tpmc Series Isys i/O WiFi TouchpanelsTPMC-8T TPMC-8XML-600 Wireless Touchpanels and HandheldsTPS-6X MT-1000CC2N-DB Mounting KeypadsC2N-DB Series Decorator Keypads Mounting in Single-Gang Box  Each keypad requires 3 watts of powerCNX Designer Series Keypads Cameo Do not use the C2N-CB with the decorator-style keypads Cameo Mounting Options Cameo Flush MountMud Ring Mount Kit ILux Integrated Lighting Control System ILux Features Wireless iLux Remote Multi-Unit Expansion Stand-alone Master with Slave wiringControl System Integration Supports incandescent, magnetic low voltage Supports 3-wire Fluorescent Fluorescent DimmingILux Expansion Modules Model Load FunctionExpansion Modules Wiring Diagrams Wall Box Dimmers and Switches Cresnet Wall Box Dimmers Model Load FeaturesCLW-SLVS Cresnet Wall Box SwitchesInfiNET Wireless Technology InfiNET Dimmers, Switches, and Thermostat Example infiNET system PAC2 Lighting Control Processor Control ProcessorsPAC2 Power Management & Requirements Series Control System PAC2M Professional Automation Mini Control SystemOverride Basic Lighting System Interconnections Occupancy and Photocell Sensors C2N-SSC-2 Integrated Shade and Drape ControllersC2N-SDC C2N-SDC-DCIntegrated Systems Integrated Partner ModulesRoomView Server Edition Appendix a RoomView Remote Asset Management Tracking of projector lamp life in bar graph format Appendix aExample RoomView Server Edition reports RoomView Express Green Light Designer Software Appendix BAppendix B Appendix C Touchpanel Comparison Charts Crestron Commercial Lighting Design GuideAppendix C Commercial Lighting Design Guide Wireless Touchpanels & Handheld RemotesTask Lighting for Specific Work Areas Appendix D General Lighting Design ConsiderationsStatic and Dynamic Elements Simple Lighting Coverage AreasKey Light Ambient Lighting for Mood and HighlightsDecorative Lighting Focal LightingColor Rendition Switch and Dimmer LocationsColor Temperature Grazing and Washing SurfacesAppendix E Glossary of Lighting Terminology Appendix E Commercial Lighting Design Guide Appendix E Doc 4775A 101 Doc 4775A 102

GLPS-HSW-FT, GLPS-HDSW-FT, GLPS-HSW, GLPS-SW-FT, GLPS-SW specifications

Crestron is a leading company in the field of automation and control technology, and their range of products continues to empower users with innovative solutions for audio-visual management and building control. Among their offerings, the GLPS-SW-FT, GLPS-HDSW-FT, GLPS-SW, GLPS-HSW, and IPAC-GL1 stand out with distinct features and capabilities designed to enhance user experiences in various environments.

The Crestron GLPS-SW-FT is a powerful presentation switcher that facilitates seamless connectivity with multiple input sources, enabling users to consolidate their AV equipment efficiently. With support for multiple resolutions and formats, this device is equipped with advanced processing capabilities, ensuring high-quality video output. Its intuitive interface simplifies operations, allowing users to switch between presentations effortlessly.

The GLPS-HDSW-FT, on the other hand, is a high-definition switcher designed specifically for HDMI connections. This model offers comprehensive support for HDCP compliance and deep color, guaranteeing optimal visual quality during presentations. Furthermore, it features built-in scaling technology, allowing for flexible display configurations that cater to various screen sizes and resolutions.

The Crestron GLPS-SW is engineered to enhance user interaction with its advanced control systems. This device integrates seamlessly with Crestron's ecosystem, providing extensive programming options that allow customization according to specific requirements. Its ability to interface with touch panels and other control devices makes it a versatile solution in corporate settings and educational institutions.

In contrast, the GLPS-HSW is recognized for its robust switching capabilities that manage HDMI, audio, and other video formats simultaneously. This device is particularly suited for complex installations where multiple sources are used. It offers remote management capabilities, enabling system integrators to monitor and control the device effectively.

Lastly, the IPAC-GL1 is a groundbreaking control interface that amalgamates user-friendly design with powerful functionality. This model provides tactile feedback and customizable buttons for precise control over AV systems. Its compact form factor makes it easy to integrate into any workspace, promoting an efficient workflow.

Collectively, these Crestron products represent a commitment to quality and innovation in the realm of AV control and management. They leverage advanced technologies and user-centric designs to meet the evolving demands of modern environments, reaching new heights in interoperability, efficiency, and ease of use. Whether for corporate presentations, educational applications, or entertainment venues, Crestron’s GLPS and IPAC offerings are tailored to provide exceptional performance and reliability.
Top Page Image Contents