Crestron electronic IPAC-GL1, GLPS-SW-FT, GLPS-HSW manual Cresnet Wall Box Switches, Clw-Slvs

Page 78

Commercial Lighting Design Guide

Wall Box Dimmers and Switches

Cresnet Wall Box Switches

Model

Load

Features

CLW-SW

Wall Box

Switch

(Stand-alone)

CLW-SW1

Wall Box

Switch, Single

Button

(Stand-alone)

CLW-SWS1

Wall Box

Master Switch,

Single Button

(Master)

CLW-SLVS1

Wall Box Slave

Switch, Single

Button

(Slave)

CLW-SWS

Wall Box Master Switch

(Master)

CLW-SLVS

Wall Box Slave Switch

(Multipoint

Slave)

Supports incandescent and electronic low voltage loads up to 1000 watts, or magnetic low-voltage and neon/cold cathode loads up to 1000VA/750 watts. Fluorescent ballasts, high- intensity discharge lighting, and ceiling fans can also be switched.

Supports incandescent and electronic low voltage loads up to 1000 watts, or magnetic low voltage and neon/cold cathode loads up to 1000VA/750 watts.

Fluorescent ballasts, high- intensity discharge lighting, and ceiling fans can also be switched.

Supports incandescent and electronic low voltage loads up to 1000 watts, or magnetic low voltage and neon/cold cathode loads up to 1000VA/750 watts.

Fluorescent ballasts, high- intensity discharge lighting, and ceiling fans can also be switched

Supports incandescent and electronic low voltage loads up to 1000 watts, or magnetic low-voltage and neon/cold cathode loads up to 1000VA/750 watts.

1000 watt electronic light switch designed to mount in a standard electrical gang box

1000-Watt electronic light switch designed to mount in a standard electrical gang box

Large button provides instant on/off control of the load, while the small button turns the load off following a preset time delay. The slide switch selects between ADJUST, PRESET, and OFF modes. PRESET mode is the normal operating mode, and ADJUST mode is used for setting the delay time.

NOTE: The wall box switches do not support fan speed control. Use the CLX-1FAN4 for fan speed control.

Provides instant turn-on control of the load. Pressing the button again turns the load off following a preset time delay. The time delay can be overridden by tapping the button a second time, turning the load off instantly. The slide switch on the CLW-SW1 selects ADJUST, PRESET, and OFF modes. PRESET mode is the normal operating mode, and ADJUST mode is used for setting the delay time.

Multiple units may be ganged side-by-side along with other CLW-Series switches and dimmers or non-Crestron devices. The single large button on the CLW-SWS1 provides instant turn-on control of the load. Pressing the button again turns the load off following a preset time delay. The time delay can be overridden by tapping the button a second time, turning the load off instantly. The slide switch on the CLW-SWS1 selects ADJUST, PRESET, and OFF modes. PRESET mode is the normal operating mode, and ADJUST mode is used for setting the delay time.

One-gang wall mount slave switch designed for use with the CLW-SWS1 Wall Box Master Switch to provide multipoint switching control of a single load. The single pushbutton on the CLW-SLVS1 provides parallel functionality to that on the CLW-SWS1.

Serves as the master for multipoint switching control of a single load. Multi-point switching functionality (similar to

3-way or 4-way switching) is enabled by using the CLW- SWS with one or more CLW-SLVS Slave Switches. The large button on the CLW-SWS allows for instant on/off control of the load, the small button turns the load off following a preset time delay. The slide switch selects between ADJUST, PRESET, and OFF modes. PRESET mode is the normal operating mode, and ADJUST mode is used for setting the delay time.

NOTE: The wall box switches do not support fan speed control. Use the CLX-1FAN4 for fan speed control.

One-gang wall mount slave switch designed for use with the CLW-SWS Wall Box Master Switch to provide multipoint switching control of a single load. The pushbuttons on the CLW-SLVS provide parallel functionality to those on the CLW-SWS.

NOTE: In systems, only the master unit is connected to Cresnet®. Slave units are connected by the120V (Traveler) wire.

Doc 4775A

74

Page 77 Page 79
Image 78
Page 77 Page 79
Contents Crestron Green Light Commercial Lighting Design Guide Page Contents Page Introduction Crestron Green LightOr any other Crestron software Single Solution Control System- Crestron Exclusive Crestron Control TechnologyOr automatic load shedding System Design Wireless Systems Lighting System Design TypesCentralized Wired Systems Decentralized Wired Systems System Design Crestron Commercial l Lighting Design GuideHybrid Systems Specifying a Lighting System Required Load Schedule ItemsLoad Schedule Complete diagram is available on line at Example Load Schedule with Panel TerminationsOrdering a Crestron Commercial Lighting System Commercial Lighting Wiring PlanEquipment List Specification Steps to order a lighting systemGreen Light Power Switching System FeaturesCan be programmed without ever having to connect a computer Green Light Power Switching Front GLPS-HSW-MLO-30-120-10K -NDMCB125 Main lug onlyMCB100 Available for 277V onlySpecifications Glps SW MLO 30 120 10K ND 100125 GLPS-SW-MLO Medium 70 x 20-1/4 x 6-5/8 in 177.8 x 51.4 x 16.8 cm Large 78-15/16 x 20-1/4 x 6-5/8 in 200.5 x 51.4 x 16.8 cmModel Numbers GLPS-HSW-FT GLPS-SW-FTGreen Light Express Feed Specifications Load Ratings Glps Hdsw FT Glps Relay Type Feed Type Number of Ckts Small 8, 16 Large 32, 40, 48GLPS-HDSW-FT Load RatingsDoc.4775A Sdram 32 MB Nvram 1 MB EthernetWall Mount 50 Watt Cresnet Power Supply GLA-PWS50120/277 Power Loss Sensor GLS-PLSDimensions Dimensions GLEP-HSW & GLEP-SW Large Panel GLEP-HSW & GLEP-SW Extra Large Panel GLEP-HSW-FT, GLEP-SW-FT, & GLEP-HDSW-FT Panels IPAC-GL1 Green Light Options CAEN- Series EnclosuresSpecifications Crestron Commercial Lighting Design Guide Caen EnclosuresCaen 2X1, 4X1, and 7X1 Framing Caen InstallationCaen Enclosure Framing Caen 4X2 FramingCaen Wiring Universal Mounting Plates Dimensions are provided in inches Cover Extension KitsCLX Lighting Control Modules CLX-Series Lighting Control Modules Model Load RatingTerminal Blocks and Modules Module Installation Single Width Enclosure MountingCresnet Terminal Block for Caen Automation Enclosures Green Light Options-CAEN Enclosures Features DIN Rail InstallationCrestron DIN Rail Products Example DIN Rail System DIN-AP2 Auto Load Detection Phase-Synchronous Detection CircuitryDIN-1DIMU4 Short Circuit ProtectionDIN-8SW8 DIN-4DIMFLV4DIN-2MC2 Analog Outputs DIN-AO8DIN-IO8 VersiportsDIN-PWS50 Cresnet Power DistributionDIN-BLOCK Cresnet DistributionDIN-HUB  3-segment Cresnet hub  32 Cresnet devices per segmentInterface Equipment TPS Isys G-Series with Crestron Home or QuickMedia Wall Mount TouchpanelsTPS Series Isys Tpmc Isys I/O with Crestron Home or QuickMediaTPS-4000L TPMC-8LTPS-4L Tilt Touchpanels TPS-4000TPMC-8X Tpmc Series Isys i/O WiFi TouchpanelsTPMC-8T TPMC-4XGMT-1000C Wireless Touchpanels and HandheldsTPS-6X ML-600Keypads C2N-DB Series Decorator KeypadsC2N-DB Mounting  Each keypad requires 3 watts of power CNX Designer Series KeypadsMounting in Single-Gang Box Cameo Cameo Mounting Options Cameo Flush Mount Mud Ring Mount KitDo not use the C2N-CB with the decorator-style keypads ILux Integrated Lighting Control System ILux Features Wireless iLux Remote Stand-alone Master with Slave wiring Multi-Unit ExpansionControl System Integration Model Load Function Supports 3-wire Fluorescent Fluorescent DimmingILux Expansion Modules Supports incandescent, magnetic low voltageExpansion Modules Wiring Diagrams Wall Box Dimmers and Switches Model Load Features Cresnet Wall Box DimmersCresnet Wall Box Switches CLW-SLVSInfiNET Wireless Technology InfiNET Dimmers, Switches, and Thermostat Example infiNET system Control Processors PAC2 Lighting Control ProcessorPAC2 Power Management & Requirements PAC2M Professional Automation Mini Control System Series Control SystemOverride Basic Lighting System Interconnections Occupancy and Photocell Sensors C2N-SDC-DC Integrated Shade and Drape ControllersC2N-SDC C2N-SSC-2Integrated Partner Modules Integrated SystemsAppendix a RoomView Remote Asset Management RoomView Server EditionAppendix a  Tracking of projector lamp life in bar graph formatExample RoomView Server Edition reports RoomView Express Appendix B Green Light Designer SoftwareAppendix B Appendix C Touchpanel Comparison Charts Crestron Commercial Lighting Design GuideAppendix C Wireless Touchpanels & Handheld Remotes Commercial Lighting Design GuideSimple Lighting Coverage Areas Appendix D General Lighting Design ConsiderationsStatic and Dynamic Elements Task Lighting for Specific Work AreasFocal Lighting Ambient Lighting for Mood and HighlightsDecorative Lighting Key LightGrazing and Washing Surfaces Switch and Dimmer LocationsColor Temperature Color RenditionAppendix E Glossary of Lighting Terminology Appendix E Commercial Lighting Design Guide Appendix E Doc 4775A 101 Doc 4775A 102

GLPS-HSW-FT, GLPS-HDSW-FT, GLPS-HSW, GLPS-SW-FT, GLPS-SW specifications

Crestron is a leading company in the field of automation and control technology, and their range of products continues to empower users with innovative solutions for audio-visual management and building control. Among their offerings, the GLPS-SW-FT, GLPS-HDSW-FT, GLPS-SW, GLPS-HSW, and IPAC-GL1 stand out with distinct features and capabilities designed to enhance user experiences in various environments.

The Crestron GLPS-SW-FT is a powerful presentation switcher that facilitates seamless connectivity with multiple input sources, enabling users to consolidate their AV equipment efficiently. With support for multiple resolutions and formats, this device is equipped with advanced processing capabilities, ensuring high-quality video output. Its intuitive interface simplifies operations, allowing users to switch between presentations effortlessly.

The GLPS-HDSW-FT, on the other hand, is a high-definition switcher designed specifically for HDMI connections. This model offers comprehensive support for HDCP compliance and deep color, guaranteeing optimal visual quality during presentations. Furthermore, it features built-in scaling technology, allowing for flexible display configurations that cater to various screen sizes and resolutions.

The Crestron GLPS-SW is engineered to enhance user interaction with its advanced control systems. This device integrates seamlessly with Crestron's ecosystem, providing extensive programming options that allow customization according to specific requirements. Its ability to interface with touch panels and other control devices makes it a versatile solution in corporate settings and educational institutions.

In contrast, the GLPS-HSW is recognized for its robust switching capabilities that manage HDMI, audio, and other video formats simultaneously. This device is particularly suited for complex installations where multiple sources are used. It offers remote management capabilities, enabling system integrators to monitor and control the device effectively.

Lastly, the IPAC-GL1 is a groundbreaking control interface that amalgamates user-friendly design with powerful functionality. This model provides tactile feedback and customizable buttons for precise control over AV systems. Its compact form factor makes it easy to integrate into any workspace, promoting an efficient workflow.

Collectively, these Crestron products represent a commitment to quality and innovation in the realm of AV control and management. They leverage advanced technologies and user-centric designs to meet the evolving demands of modern environments, reaching new heights in interoperability, efficiency, and ease of use. Whether for corporate presentations, educational applications, or entertainment venues, Crestron’s GLPS and IPAC offerings are tailored to provide exceptional performance and reliability.
Top Page Image Contents