Heatiator HEIR50T Burned Portion Edge of LOG Used For Positioning For LOG #5, HEIR42 Shown

Page 56

Log #5 (2284-705): Locate flat areas on Log #1 and Log #3 that will be used to position Log #5. See Figure 11. Place Log #5 into appliance as shown in Figure 12. Log #5 should contact base refractory and rest on the flat areas as shown in Figure 11. Burned portion of Log #5 should be in front of Log #1. Log should be about 1/2 inch from front outer edge of base refractory when properly positioned. See Figure 12.

BURNED

PORTION

5

6

EDGE OF LOG USED

FOR POSITIONING

Figure 10.

FOR LOG #5

1

FOR

LOG #5

2 FOR LOG #6

3

Figure 11.

Log #6 (2284-706): Locate flat areas on Log #2 and Log #3 that will be used to position Log #6. See Figure 11. Place Log #6 into appliance as shown in Figure 13. Edge of Log #6, highlighted in Figure 10, will be about 1/2 inch from the center grate tine on both HEIR36 and HEIR42. Right side of log contacts right grate tine.

4

1

5

2

3

BURNED

PORTION

1/2 INCH

LOG DOES NOT

2CONTACT GRATE

TINE

1/2 INCH

HEIR42 SHOWN

Figure 12. Log #5 Placement

Figure 13. Log #6 Placement

4

1

6 5

2

3

Figure 14. Log Set Installed.

2284-935C

56

Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev. D • 8/12

Page 55 Page 57
Image 56
Page 55 Page 57
Contents Models What to do if you smell gasDo Discardnot HOT SurfacesCongratulations Homeowner Reference InformationTable of Contents User GuideReference Materials Appliance SetupTroubleshooting Limited Lifetime Warranty Limited Lifetime WarrantyWarranty Conditions Listing and Code Approvals Installation of Carbon Monoxide Detectors Requirements for the Commonwealth of MassachusettsYour Fireplace Gas Fireplace SafetyOperating Instructions User Guide Fixed Glass Assembly Remote Controls, Wall Controls and Wall SwitchesIPI Battery Tray/Battery Installation Clear SpaceModule Reset Nine Hour Safety Shutdown FeatureControl Module Operation Before Lighting FireplaceLighting Instructions IPI Final inspection byWhat to do if YOU Smell GAS GAS ValveAfter Fireplace is Lit Frequently Asked QuestionsIssue Solutions Maintenance and Service Maintenance Tasks-HomeownerGlass Cleaning Exterior of Installed Glass Only Remote Control OptionalMaintenance Tasks-Qualified Service Technician Glass Cleaning Exterior and Interior of Installed GlassGasket Seal and Glass Assembly Inspection LogsBurner Ignition and Operation IPI Pilot Flame PatternsGetting Started Typical Appliance SystemInspect Appliance and Components Design and Installation ConsiderationsTools and Supplies Needed Framing and Clearances Selecting Appliance LocationHEIR36 HEIR42Clearances Minimum Framing DimensionsConstructing the Appliance Chase Mantel and Wall Projections Non-Combustible ZoneCombustible Mantel Legs or Wall Projections Non-Combustible Mantel Legs or Wall ProjectionsNON-COMBUSTIBLE Material HEIR50 Fireplace Opening Combustible Mantel Allowance HEIR36, HEIR42Hearth Extension ModelTermination Locations Vent Termination Minimum ClearancesClearance above electrical service Covered Alcove ApplicationsVent Information and Diagrams HEIR36 NG/LP, HEIR42 NG/LP HEIR50 NG/LP Top Vent Horizontal TerminationOne Elbow Two Elbows H1+ H2Top Vent Horizontal Termination Three Elbows HEIR36 NG/LP, HEIR42 NG/LP, HEIR50 NG/LPFlue Restrictor Top Vent Vertical Termination ElbowsTop Vent Vertical Termination Three Elbows Ht MaxPVK-80 and PVI-SLP Information PVI-SLPHEIR36 HEIR42Vent Clearances and Framing Pipe Clearances to CombustiblesWall Penetration Framing Non-Combustible Wall PenetrationInstall the Ceiling Firestop Pipe DVPInstall Attic Insulation Shield Installing the Optional Heat-ZoneGas KitFlat Ceiling Installation Vaulted Ceiling InstallationAppliance Preparation Vent PreparationSecuring and Leveling the Appliance Side Nailing Tab in Shipping PositionInstalling Non-combustible Facing Material Installing Non-Combustible Facing MaterialInstalling Vent Pipe DVP Pipe Attach Vent to the Firebox AssemblyAssemble Vent Sections Assemble Pipe SectionsSecure the Vent Sections Disassemble Vent SectionsInstall Metal Roof Flashing Assemble and Install Storm CollarHeat Shield Requirements for Horizontal Termination Install Vertical Termination CapInstall Horizontal Termination Cap Gas Information Fuel ConversionGas Pressure Gas ConnectionWiring Requirements IntelliFire PlusTM Ignition System WiringOptional Accessories Requirements Electrical InformationElectrical Service and Repair Junction Box Installation Access Through Left Column Access Through FireboxFinishing Templates Template installation instructionFinishing Splatter Guard Finishing Template Bends Inoperable Fixed DoorsNon-Combustible Zone Combustible Mantel Projections 10 Combustible Mantel Allowance HEIR36, HEIR42Facing Material Model HEIR36Dimension Inoperable Operable Door DoorsArch Operable DoorsAppliance Setup Install the Log Assembly Log Set Assembly LOGS-HEIR36 LOG Placement Tabs LOG Placement Slot Notch forModels HEIR36H, HEIR36S LOG#4Burner Grate Notch LOG Contacts Notch Rests On Burner Grate Tine HEIR42 onlyBurned Edge Portion Contacts BackBurned Portion Edge of LOG Used For Positioning For LOG #5 Burned PortionLOG does not 2CONTACT Grate Tine HEIR42 ShownLog Set Assembly LOGS-HEIR50 Models HEIR50T, HEIR50H LOG Contacts Grate TineBurned Edge LOG Contacts Side Refractory LOG Contacts Grate Tine Approximately HEIR36 HEIR42 HEIR50 TOP Retaining Rail Notch Glass Frame Notch Air Shutter Setting Air Shutter SettingsFlame Appearance Full OpenIntelliFire Plus Ignition System TroubleshootingSymptom Possible Cause Corrective Action Troubleshooting Appliance Dimension Diagram Reference Materials1905 Vent Components Diagrams DVP-AS2DVP-TRAP1 DVP-TRAP2 DVP-TRAPK1 DVP-TRAPK2 DVP-TRAPRF6M RF12M BEK DVP-BEK2DVP-TRAPFL COOL-ADDSLP-LPC Optional Wire HarnessDescription Part Number Service Parts Log Set AssemblyAt Depot Description Comments Part NumberDescription Comments Part Number #19 Traditional Refractory #20 Herringbone RefractoryStocked HEIR42T, HEIR42H HEIR42T, HEIR42H Log Set Assembly HEIR50T, HEIR50H#20 Traditional Refractory #21 Herringbone Refractory #11 Valve Assembly HEIR36, HEIR42, HEIR50MYSTIC-EMBERS Contact Information

HEIR50H, HEIR36T, HEIR36H, HEIR50T, HEIR42T specifications

The Heatiator range of heating appliances, including the HEIR36T, HEIR50T, HEIR42H, HEIR42T, and HEIR50H, represents a blend of cutting-edge technology and stylish design, tailored to meet various heating needs in residential spaces. Each model exhibits unique features, yet shares a commitment to efficiency and user-friendliness.

Starting with the HEIR36T, this model is compact yet powerful, making it ideal for smaller living areas. It boasts an efficient heating system that utilizes advanced ceramic heating elements, ensuring rapid warmth. The sleek design is complemented by a digital control panel, allowing users to easily adjust settings for optimal comfort.

In contrast, the HEIR50T caters to larger rooms, offering increased power and a higher heat output. Its robust construction is designed for durability, while energy-efficient technology minimizes operational costs. The HEIR50T comes equipped with a programmable thermostat, enabling users to set heating schedules to align with their lifestyle.

The HEIR42H stands out with its hybrid heating capability, combining traditional radiant heat with modern convection elements. This dual functionality allows for faster and more even heat distribution throughout the space. The HEIR42H is particularly popular for its versatility, suitable for use in various environments from homes to commercial spaces.

The HEIR42T model shares many of the benefits of the HEIR42H but focuses on a sleek, slim-line design that doesn’t compromise on performance. Ideal for minimalistic interiors, it offers the same advanced heating technology, ensuring efficient warmth without taking up excess space.

Lastly, the HEIR50H is designed for heavy-duty performance, making it the perfect choice for larger areas that require substantial heating power. It features enhanced insulation and expanded heating elements, ensuring that even the coldest rooms achieve a comfortable temperature quickly.

In summary, the Heatiator HEIR series exemplifies innovation in home heating solutions. With various models to choose from, customers can select the unit that best suits their space requirements while benefiting from technologies designed for efficiency and comfort. The digital controls, programmable settings, and modern designs make these heaters both functional and aesthetically pleasing, reinforcing Heatiator's commitment to quality and user satisfaction.
Top Page Image Contents