Desa CRL3124P/N Variable Control Operation, To Turn Off Gas To Appliance, Shutting Off Heater

Page 21
VARIABLE CONTROL

OPERATING HEATER

Continued

5.Slightly depress and turn control knob

counterclockwiseTO TURN OFF GAS to the PILOT po- sition. Press in control knob for five (5) sec- onds (see Figure 35).

Note: You may be running this heater for the first time after hooking up to gas sup- ply. If so, the control knob may need to be pressed in for 30 seconds or more. This will allow air to bleed from the gas system.

6.With control knob pressed in, press and re- lease ignitor button. This will light pilot. The pilot is attached to the burner. If needed, keep pressing ignitor button until pilot lights.

Note: If pilot does not stay lit, contact a qualified service person or gas supplier for repairs. Until repairs are made, light pilot with match. To light pilot with match, see Manual Lighting Procedure.

7.Keep control knob pressed in for 30 sec- onds after lighting pilot. After 30 seconds, release control knob.

Note: If pilot goes out, repeat steps 3 through 7. If control knob does not pop out when released, contact a qualified service person or gas supplier for repairs.

8.Slightly depress and turn control knob

counterclockwise Shutting Off Heater to desired heat- ing level. The burner(s) should light. Set control knob to any heat level between HI and LO.

Shutting Off Burner(s) Only (pilot stays lit) WARNING: Do not operate heater between PILOT and HI positions.

HI PILOT

MANUAL LIGHTING OFF

LO

Control Knob

Ignitor Button

Figure 35 - Control Knob and Ignitor

Button Location

Ignitor

Pilot Burner

Electrode

 

Thermocouple

Figure 36 - Pilot

VARIABLE CONTROL

OPERATION

The variable control valve can be set to any heat setting and flame height desired, by simply turning the control knob until that setting is attained. Even the lowest setting provides real- istic, dancing yellow flames. Selecting higher settings produces greater heat output. This re- sults in increased heating comfort.

Manual background CAUTION: Do not try to ad- just heating levels by using the equipment shutoff valve.

TO TURN OFF GAS

TO APPLIANCE

Shutting Off Heater

1.Press in and turn control knob clockwise Manual background to the HI position.

2.Turn control knob clockwise Manual background to the pilot position.

3.Press in control knob and turn clockwise Manual background to the OFF position.

Shutting Off Burner(s) Only (pilot stays lit)

1.Turn control knob clockwise Manual background to the HI position.

2.Press in and turn control knob clockwise Manual background to the pilot position.

MANUAL LIGHTING

PROCEDURE

1. Follow steps 1 through 5 under Lighting In- structions, pages 20 and 21.

2.Depress control knob and light pilot with match.

3.Keep control knob pressed in for 30 sec- onds after lighting pilot. After 30 seconds, release control knob. Now follow step 8, under Lighting Instructions, column 1.

111160-01C

www.desatech.com

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents —WHAT TO DO IF YOU SMELL GAS TABLE OF CONTENTS SAFETY INFORMATION SAFETY INFORMATION PRODUCT IDENTIFICATIONContinued SAFETY PILOT PRODUCT FEATURESLOCAL CODES UNPACKINGDETERMINING FRESH-AIRFLOW FOR HEATER LOCATION ContinuedContinued 5.3or applicable local codesVENTILATION AIR Figure 3 - Ventilation Air from Inside BuildingINSTALLATION MINIMUM FIREPLACE CLEARANCE ContinuedContinued Without Using HoodMANTEL CLEARANCES Figure 6 - Heat Resistant Material SlateContinued When Using HoodFLOOR CLEARANCES Figure 10 - Minimum FireplaceINSTALLING HEATER BASE ASSEMBLY CONNECTING TO GAS SUPPLY Figure 13 - Attaching Base Assembly toFireplace Floor - Dual Burner Model CHECKING GAS CONNECTIONS Figure 17 - Equipment Shutoff Valve ContinuedFigure 18 - Checking Gas Joints Propane/LP Gas ModelsINSTALLING LOGS damage or personal injuryContinued Figure 26 - Installing Rear Log #3 Figure 25 - Installing Middle Log #2Figure 27 - Installing Crossover Log #4 Figure 24 - Installing Front Log #1Figure 31 - Installing Crossover Log #7 Figure 29 - Installing Crossover Log #5Continued HolesFigure 32 - Installing Back Log Back Log Post Base Assembly PostAssembly Figure 33 - Installing Front LogOPERATING HEATER MANUALLY-CONTROLLED MODELS FOR YOUR SAFETYREAD BEFORE LIGHTING LIGHTING INSTRUCTIONSVARIABLE CONTROL OPERATION MANUAL LIGHTING PROCEDURETO TURN OFF GAS TO APPLIANCE Shutting Off Heater1.STOP! Read the safety information, col- umn THERMOSTAT-CONTROLLED MODELS FOR YOUR SAFETYREAD BEFORE LIGHTING LIGHTING INSTRUCTIONSContinued MANUAL LIGHTING PROCEDURETO TURN OFF GAS TO APPLIANCE THERMOSTAT CONTROL OPERATIONBURNER PRIMARY AIR HOLES PILOT FLAME PATTERNMAIN BURNER BURNER INJECTOR HOLDER AND PILOT AIR INLET HOLELOGS ContinuedMAIN BURNER Figure 41 - Injector Holder On Outlet Burner TubeOBSERVED PROBLEM TROUBLESHOOTINGPOSSIBLE CAUSE REMEDYContinued OBSERVED PROBLEMPOSSIBLE CAUSE REMEDYWARNING: If you smell gas •Shut off gas supply FOR MASONRY AND FACTORY- BUILT METAL FIREPLACE Assembly and Thermostat Sensing BulbFigure 44 - Adhesive-backedMounting Clip Figure 45 - Removing Thermostat Sensing BulbPARTS UNDER WARRANTY REPLACEMENT PARTSPARTS NOT UNDER WARRANTY OPTIONAL POSITIONING OF THERMOSTAT SENSING BULBDUAL BURNER SMOKY MOUNTAIN OAK MODELS SPECIFICATIONSDUAL BURNER BILTMORE SPLIT OAK MODELS SINGLE BURNER SEASONAL OAK MODELSILLUSTRATED PARTS BREAKDOWN PARTS LIST 19 11 13 9 6 21 21 5 4 3 201 2 10 7 14 8 15 21 19 17 21103008-02 3 12 6 9 16 10 17 23 18 22 1420 24 21 13 15 11 8 23 2321 23 111160-01C111340-03 Peg positions vary according to model 2 5 111160-01C22 1420 24 21 13 15 11 8 23 23 9 7 12 6 25 16 10 17 23 18111340-02 111160-01C VARIABLE MANUALLY-CONTROLLEDSEASONAL OAK MODELS Portable Heater Parts PARTS CENTRALMaster Parts Dist Washer Equipment CoINFORMATION VIDEO - EQUIPMENT SHUTOFF VALVE - GA5010FIREPLACE HOOD DAMPER CLAMP - GA6080 Not ShownLIMITED WARRANTY KEEP THIS WARRANTYModel ____________________________ Serial No. _________________________
Top Page Image Contents