Desa CRL2718P/N, CRL3124P/N, CGD3018PT/NT, CGD3924PT/NT installation manual Installation

Page 8
INSTALLATION

INSTALLATION

NOTICE: This heater is intended for use as supplemental heat. Use this heater along with your primary heating system. Do not install this heater as your pri- mary heat source. If you have a central heating system, you may run system’s circulating blower while using log heater. This will help circulate the heat from your log heater throughout the house. In the event of a power outage, you can use this heater as your primary heat source.

Manual background WARNING: A qualified ser- vice person must install heater. Follow all local codes.

NOTICE:Stateorlocalcodesmay only allow operation of this appli- ance in a vented configuration. Check your state or local codes.

Manual backgroundWARNING: Before installing in a solid fuel burning fireplace, thechimneyflueandfireboxmust be cleaned of soot, creosote, ashes, and loose paint by a quali- fied chimney cleaner. Creosote will ignite if highly heated. A dirty chimney flue may create and dis- tributesootwithinhouse.Inspect chimneyflueandfireboxfordam- age. If damaged, repair flue and firebox before operating heater.

Manual background WARNING: Seal any fresh air vents or ash clean-out doors located on floor or wall of fire- place. If not, drafting may cause pilot outage or sooting. Use a heat-resistant sealant. Do not seal chimney flue damper.

Manual backgroundWARNING: Never install the heater

•in a bedroom or bathroom un- less installed as a vented ap- pliance (Variable Manually- Controlled Models Only) (see page 12)

•in a recreational vehicle

•where curtains, furniture, clothing, or other flammable objects are less than 42 inches from the front, top, or sides of the heater

•in high traffic areas

•in windy or drafty areas

Manual background CAUTION: This heater cre- ates warm air currents. These currents move heat to wall sur- faces next to heater. Installing heater next to vinyl or cloth wall coverings or operating heater where impurities (such as, but not limited to, tobacco smoke, aromatic candles, cleaning flu- ids, oil or kerosene lamps, etc.) in the air exist, may discolor walls or cause odors.

IMPORTANT: Vent-free heaters add moisture to the air. Although this is beneficial, installing heater in rooms without enough ventilation air may cause mildew to form from too much moisture. See Air for Combustion and Ventilation, pages 5 through 7.

CHECK GAS TYPE

Use the correct gas type (natural or propane/LP) for your unit. If your gas supply is not correct, do not install heater. Call dealer where you bought heater for proper type heater.

Manual background WARNING: This appliance is equipped for (natural or pro- pane/LP) gas. Field conversion is not permitted.

8

www.desatech.com

111160-01C

Page 7 Page 9
Image 8
Page 7 Page 9
Contents —WHAT TO DO IF YOU SMELL GAS TABLE OF CONTENTS SAFETY INFORMATION Continued SAFETY INFORMATIONPRODUCT IDENTIFICATION PRODUCT FEATURES SAFETY PILOTLOCAL CODES UNPACKINGContinued DETERMINING FRESH-AIRFLOW FOR HEATER LOCATION5.3or applicable local codes ContinuedVENTILATION AIR Figure 3 - Ventilation Air from Inside BuildingINSTALLATION Continued MINIMUM FIREPLACE CLEARANCEWithout Using Hood ContinuedMANTEL CLEARANCES Figure 6 - Heat Resistant Material SlateWhen Using Hood ContinuedFLOOR CLEARANCES Figure 10 - Minimum FireplaceINSTALLING HEATER BASE ASSEMBLY Fireplace Floor - Dual Burner Model CONNECTING TO GAS SUPPLYFigure 13 - Attaching Base Assembly to CHECKING GAS CONNECTIONS Continued Figure 17 - Equipment Shutoff ValveFigure 18 - Checking Gas Joints Propane/LP Gas ModelsContinued INSTALLING LOGSdamage or personal injury Figure 25 - Installing Middle Log #2 Figure 26 - Installing Rear Log #3Figure 27 - Installing Crossover Log #4 Figure 24 - Installing Front Log #1Figure 29 - Installing Crossover Log #5 Figure 31 - Installing Crossover Log #7Continued HolesBack Log Post Base Assembly Post Figure 32 - Installing Back LogAssembly Figure 33 - Installing Front LogMANUALLY-CONTROLLED MODELS FOR YOUR SAFETY OPERATING HEATERREAD BEFORE LIGHTING LIGHTING INSTRUCTIONSMANUAL LIGHTING PROCEDURE VARIABLE CONTROL OPERATIONTO TURN OFF GAS TO APPLIANCE Shutting Off HeaterTHERMOSTAT-CONTROLLED MODELS FOR YOUR SAFETY 1.STOP! Read the safety information, col- umnREAD BEFORE LIGHTING LIGHTING INSTRUCTIONSMANUAL LIGHTING PROCEDURE ContinuedTO TURN OFF GAS TO APPLIANCE THERMOSTAT CONTROL OPERATIONPILOT FLAME PATTERN BURNER PRIMARY AIR HOLESMAIN BURNER BURNER INJECTOR HOLDER AND PILOT AIR INLET HOLEContinued LOGSMAIN BURNER Figure 41 - Injector Holder On Outlet Burner TubeTROUBLESHOOTING OBSERVED PROBLEMPOSSIBLE CAUSE REMEDYOBSERVED PROBLEM ContinuedPOSSIBLE CAUSE REMEDYWARNING: If you smell gas •Shut off gas supply Assembly and Thermostat Sensing Bulb FOR MASONRY AND FACTORY- BUILT METAL FIREPLACEFigure 44 - Adhesive-backedMounting Clip Figure 45 - Removing Thermostat Sensing BulbREPLACEMENT PARTS PARTS UNDER WARRANTYPARTS NOT UNDER WARRANTY OPTIONAL POSITIONING OF THERMOSTAT SENSING BULBSPECIFICATIONS DUAL BURNER SMOKY MOUNTAIN OAK MODELSDUAL BURNER BILTMORE SPLIT OAK MODELS SINGLE BURNER SEASONAL OAK MODELSILLUSTRATED PARTS BREAKDOWN PARTS LIST 4 3 20 19 11 13 9 6 21 21 51 2 10 7 14 8 15 21 19 17 21103008-02 22 1420 24 21 13 15 11 8 23 23 3 12 6 9 16 10 17 23 1821 23 111160-01C111340-03 111160-01C Peg positions vary according to model 2 522 1420 24 21 13 15 11 8 23 23 9 7 12 6 25 16 10 17 23 18111340-02 111160-01C VARIABLE MANUALLY-CONTROLLEDSEASONAL OAK MODELS PARTS CENTRAL Portable Heater PartsMaster Parts Dist Washer Equipment CoEQUIPMENT SHUTOFF VALVE - GA5010 INFORMATION VIDEO -FIREPLACE HOOD DAMPER CLAMP - GA6080 Not ShownKEEP THIS WARRANTY LIMITED WARRANTYModel ____________________________ Serial No. _________________________
Top Page Image Contents