Desa CRL3124P/N Continued, Installing Middle Log #2, CCL3930PTB/NTB Shown, Installing Rear Log #3

Page 17

Figure 25 - Installing Middle Log #2

INSTALLATION

Continued

WARNING:Failuretoposition thepartsinaccordancewiththese diagrams or failure to use only parts specifically approved with this heater may result in property damage or personal injury.

Dual Burner Biltmore Split Oak Models CCL3018PTA/NTA, CCL3924PTA/NTA, CCL3930PTB/NTB

Each log is marked with a number. These num- bers will help you identify the log when install- ing. It is very important to install these logs ex- actly as instructed. Do not modify logs. Only use logs supplied with heater.

1.Place the front log (#1) on the grate fingers. Make sure the front log rests firmly between the grate fingers and the grate base (see Figure 24).

2.Place the base of the middle log (#2) in the U- shaped slots of the grate base. The cutout on the right of the middle log should fit over the burner (see Figure 25). Make sure the front of the middle log is resting on the tabs of the grate base.

3.Locate pins on the bottom of back log (#3). Slide these pins into the holes in the grate base behind the burner (see Figure 26).

4.Locate holes on the bottom of crossover log (#4). Slide front hole onto the left pin (CCL3924PTA/NTA or CCL3930PTB/NTB) or middle pin (CCL3018PA/NA or CCL3018PTA/NTA) on the middle log (#2) and the pin on the back log (#3). See Figure 27 for placement.

Front

Log (#1)

Grate

Fingers

Middle

Log (#2)

Burner

Tab	U-Shaped Slot

Figure 25 - Installing Middle Log #2

(CCL3930PTB/NTB Shown)

Pins

Rear

Log (#3)

Hole in

Grate Base

Burner

Figure 26 - Installing Rear Log #3

(CCL3930PTB/NTB Shown)

		Crossover
		Log (#4)
	Middle	Pins
	Middle	Back Log
	Log (#2)	Back Log
	Log (#2)	(#3)
		(#3)

Figure 27 - Installing Crossover Log #4

(CCL3930PTB/NTB Shown)

Grate

Base

Figure 24 - Installing Front Log #1

(CCL3930PTB/NTB Shown)

111160-01C

www.desatech.com

17

Image 17

Contents —WHAT TO DO IF YOU SMELL GAS TABLE OF CONTENTS SAFETY INFORMATION Continued SAFETY INFORMATIONPRODUCT IDENTIFICATION SAFETY PILOT PRODUCT FEATURESLOCAL CODES UNPACKINGDETERMINING FRESH-AIRFLOW FOR HEATER LOCATION ContinuedContinued 5.3or applicable local codesVENTILATION AIR Figure 3 - Ventilation Air from Inside BuildingINSTALLATION MINIMUM FIREPLACE CLEARANCE ContinuedContinued Without Using HoodMANTEL CLEARANCES Figure 6 - Heat Resistant Material SlateContinued When Using HoodFLOOR CLEARANCES Figure 10 - Minimum FireplaceINSTALLING HEATER BASE ASSEMBLY Fireplace Floor - Dual Burner Model CONNECTING TO GAS SUPPLYFigure 13 - Attaching Base Assembly to CHECKING GAS CONNECTIONS Figure 17 - Equipment Shutoff Valve ContinuedFigure 18 - Checking Gas Joints Propane/LP Gas ModelsContinued INSTALLING LOGSdamage or personal injury Figure 26 - Installing Rear Log #3 Figure 25 - Installing Middle Log #2Figure 27 - Installing Crossover Log #4 Figure 24 - Installing Front Log #1Figure 31 - Installing Crossover Log #7 Figure 29 - Installing Crossover Log #5Continued HolesFigure 32 - Installing Back Log Back Log Post Base Assembly PostAssembly Figure 33 - Installing Front LogOPERATING HEATER MANUALLY-CONTROLLED MODELS FOR YOUR SAFETYREAD BEFORE LIGHTING LIGHTING INSTRUCTIONSVARIABLE CONTROL OPERATION MANUAL LIGHTING PROCEDURETO TURN OFF GAS TO APPLIANCE Shutting Off Heater1.STOP! Read the safety information, col- umn THERMOSTAT-CONTROLLED MODELS FOR YOUR SAFETYREAD BEFORE LIGHTING LIGHTING INSTRUCTIONSContinued MANUAL LIGHTING PROCEDURETO TURN OFF GAS TO APPLIANCE THERMOSTAT CONTROL OPERATIONBURNER PRIMARY AIR HOLES PILOT FLAME PATTERNMAIN BURNER BURNER INJECTOR HOLDER AND PILOT AIR INLET HOLELOGS ContinuedMAIN BURNER Figure 41 - Injector Holder On Outlet Burner TubeOBSERVED PROBLEM TROUBLESHOOTINGPOSSIBLE CAUSE REMEDYContinued OBSERVED PROBLEMPOSSIBLE CAUSE REMEDYWARNING: If you smell gas •Shut off gas supply FOR MASONRY AND FACTORY- BUILT METAL FIREPLACE Assembly and Thermostat Sensing BulbFigure 44 - Adhesive-backedMounting Clip Figure 45 - Removing Thermostat Sensing BulbPARTS UNDER WARRANTY REPLACEMENT PARTSPARTS NOT UNDER WARRANTY OPTIONAL POSITIONING OF THERMOSTAT SENSING BULBDUAL BURNER SMOKY MOUNTAIN OAK MODELS SPECIFICATIONSDUAL BURNER BILTMORE SPLIT OAK MODELS SINGLE BURNER SEASONAL OAK MODELSILLUSTRATED PARTS BREAKDOWN PARTS LIST 19 11 13 9 6 21 21 5 4 3 201 2 10 7 14 8 15 21 19 17 21103008-02 3 12 6 9 16 10 17 23 18 22 1420 24 21 13 15 11 8 23 2321 23 111160-01C111340-03 Peg positions vary according to model 2 5 111160-01C22 1420 24 21 13 15 11 8 23 23 9 7 12 6 25 16 10 17 23 18111340-02 111160-01C VARIABLE MANUALLY-CONTROLLEDSEASONAL OAK MODELS Portable Heater Parts PARTS CENTRALMaster Parts Dist Washer Equipment CoINFORMATION VIDEO - EQUIPMENT SHUTOFF VALVE - GA5010FIREPLACE HOOD DAMPER CLAMP - GA6080 Not ShownLIMITED WARRANTY KEEP THIS WARRANTYModel ____________________________ Serial No. _________________________