Desa VMH3000TPA Mounting Heater on Optional Hearth Base, Placing Heater On Mounting Bracket

Page 10

10

INSTALLATION

A. Mounting Heater To Wall (Cont.)

B. Mounting Heater On Optional Hearth Base

INSTALLATION

Continued

Attaching To Wall Anchor Method

For attaching mounting bracket to hollow walls (wall areas between studs) or solid walls (concrete or masonry).

1.Drill holes at marked locations using 5/16" drill bit. For solid walls (concrete or masonry), drill at least 1" deep.

2.Fold wall anchor as shown in Figure 12.

3.Insert wall anchor (wings first) into hole. Tap anchor flush to wall.

4.For thin walls (1/2" or less), insert red key into wall anchor. Push red key to “pop” open anchor wings. IMPORTANT: Do not hammer key! For thick walls (over 1/2" thick) or solid walls, do not pop open wings.

5.Place mounting bracket onto wall. Line up last hole on each end of bracket with wall anchors.

6.Insert mounting screws through bracket and into wall anchors.

7.Tighten screws until mounting bracket is firmly fastened to wall.

Figure 12 - Folding Anchor

Figure 13 - Popping Open Anchor Wings For Thin Walls

Placing Heater On Mounting Bracket

1.Locate two horizontal slots on back panel of heater.

2.Place heater onto mounting bracket. Slide horizontal slots onto stand-out tabs on mounting bracket.

Horizontal Slots

Mounting Bracket (attached to wall)

Stand-Out Tab

Figure 14 - Mounting Heater Onto Mounting Bracket

Installing Bottom Mounting Screws

1.Locate two bottom mounting holes. These holes are near bot- tom on back panel of heater (see Figure 15).

2.Mark screw locations on wall.

3.Remove heater from mounting bracket.

4.If installing bottom mounting screws into hollow or solid wall, install wall anchors. Follow steps 1 through 4 under Attaching To Wall Anchor Method. If installing bottom mounting screw into wall stud, drill holes at marked locations using 9/64" drill bit.

5.Replace heater onto mounting bracket.

6.Place spacers between bottom mounting holes and wall an- chor or drilled hole.

7.Hold spacer in place with one hand. With other hand, insert mounting screw through bottom mounting hole and spacer. Place tip of screw in opening of wall anchor or drilled hole.

8.Tighten both screws until heater is firmly secured to wall. Do not over tighten. Note: Do not replace front panel at this time. Replace front panel after making gas connections and check- ing for leaks (see pages 12 and 13).

Figure 15 - Installing Bottom Mounting Screws

B. MOUNTING HEATER ON OPTIONAL HEARTH BASE

Tools needed

•#2 Phillips screwdriver

•Slotted screwdriver

•Electric drill (if securing base to floor)

The optional hearth base kit includes the following:

•Hearth base

•4 wood screws

•4 sheet metal screws

•Brass base trim

•Hearth insert

•4 anchors

•2 brass screws

For..com

109889

Page 9 Page 11
Image 10
Page 9 Page 11
Contents What to do if YOU Smell GAS 15,000 to 30,000 Btu/Hr With ThermostatTable of Contents Safety InformationProduct Identification Local CodesUnpacking Product Features Assembling HeaterAttaching Brass Front Trim to Front Panel AssemblyAIR for Combustion and Ventilation Assembling and Attaching Brass TrimUnusually Tight Construction Providing Adequate VentilationDetermining FRESH-AIR Flow for Heater Location Confined and Unconfined SpaceVentilation Air From Inside Building Ventilation AIRVentilation Air From Outdoors Check GAS Type InstallationInstallation Items Locating HeaterThermostat Sensing Bulb Installation OptionsMounting Heater to Wall Mounting Heater on Optional Hearth Base Installing Bottom Mounting ScrewsPlacing Heater On Mounting Bracket Mounting Heater to Optional Hearth Base Securing Hearth Base to FloorSee Instructions Included With Mantel Kit Assembling Mantel Connecting to GAS Supply Internally-tinned copper tubing may be used in cerPressure Testing Heater Gas Connections Pressure Testing Gas Supply Piping SystemChecking GAS Connections Operating Heater For Your Safety Read Before LightingLighting Instructions Inspecting Burner Cabinet Cleaning MaintenanceCleaning Burner Injector Holder and Pilot AIR Inlet Hole Air PassagewaysTroubleshooting Observed Problem Possible Cause RemedyMaintenance, Observed Problem Possible Cause Service Hints SpecificationsReplacement Parts Technical ServiceAccessories Illustrated Parts Breakdown RFN30TA RFP30TA VMH3000TNA VMH3000TPAParts List NJF-8CParts Centrals FBDOwners Registration Form Postage Required 109889 Not a UPC

VMH3000TPA specifications

The Desa VMH3000TPA is a state-of-the-art heating appliance designed to deliver efficient warmth while ensuring user comfort and convenience. This model is widely recognized for its innovative technologies, smart design, and eco-friendly features, making it an ideal choice for residential spaces.

One of the standout features of the VMH3000TPA is its powerful heating capacity. With a robust output of 30,000 BTUs, it is engineered to heat large areas effectively, making it perfect for living rooms, open-plan spaces, or even workshops. Users can expect a consistent and reliable warmth throughout the chilly seasons, enhancing home comfort while reducing reliance on traditional heating systems.

The VMH3000TPA incorporates advanced heating technology, including a variable speed blower that allows for more efficient heat distribution. This feature ensures that warm air circulates evenly throughout the room, eliminating cold spots and creating a cozy atmosphere. Additionally, the unit has a programmable thermostat, allowing users to set and maintain their desired temperature easily.

For safety, the VMH3000TPA is equipped with multiple safety features, including an automatic shut-off function that activates if the unit overheats or tips over. This ensures peace of mind, especially in households with children or pets. Its durable construction includes a fireproof casing and a heat-resistant glass front, designed to withstand high temperatures while maintaining an attractive appearance.

The Desa VMH3000TPA is also designed with energy efficiency in mind. It operates on propane or natural gas, providing a cleaner-burning alternative to traditional heating methods. This model complies with environmental regulations, helping to reduce carbon emissions while lowering energy costs.

Another remarkable aspect is its user-friendly interface, which includes remote control functionality. Users can conveniently adjust settings from a distance, enhancing usability and comfort. This modern appliance is not just a heating solution; it is a blend of technology and design, ensuring that it complements any home décor while providing effective heating solutions.

In summary, the Desa VMH3000TPA stands out in the heating appliance market for its powerful performance, intelligent features, energy efficiency, and safety standards, making it a worthy investment for modern households seeking comfort and reliability during the colder months.
Top Page Image Contents