Desa VMH3000TPA Thermostat Sensing Bulb, Installation Options, Mounting Heater to Wall

Page 9

INSTALLATION

Thermostat Sensing Bulb

Installation Options

A. Mounting Heater To Wall

9

INSTALLATION

Continued

THERMOSTAT SENSING BULB

The thermostat sensing bulb has been placed inside the heater for protection during shipping.

Locating Thermostat Sensing Bulb

1.Remove front panel of heater (see Figure 2, page 4).

2.Locate thermostat sensing bulb just under burner assembly.

IMPORTANT: Attach thermostat sensing bulb to back of heater for proper operation.

Attaching Thermostat Sensing Bulb

1.Remove thermostat sensing bulb from holders inside heater. Route through slot opening in bottom of heater.

2.Place clamp on thermostat sensing bulb as shown in Figure 10. Clamp is provided in hardware package.

3.Snap clamp into upper mounting hole as shown in Figure 10. Mounting hole is located on lower left edge on back of heater. Make sure the thermostat sensing bulb is pointing up.

Thermostat

Sensing Bulb

Clamp

Figure 10 - Attaching Thermostat Sensing Bulb

INSTALLATION OPTIONS

There are three options for mounting this heater.

A.Mounting heater to wall

B.Mounting heater to optional hearth base

C.Mounting heater with optional hearth base to optional mantel.

A. MOUNTING HEATER TO WALL

Mounting Bracket

The mounting bracket is located in the package tray. Remove mounting bracket from tray.

Methods For Attaching Mounting Bracket To Wall

Only use last hole on each end of mounting bracket to attach bracket to wall. These two holes are 16 inches apart from their centers. Attach mounting bracket to wall in one of two ways.

1.Attaching to wall stud

2.Attaching to wall anchor

Attaching to Wall Stud: This method provides the strongest hold. Insert mounting screws through mounting bracket and into wall studs.

Attaching to Wall Anchor: This method allows you to attach mounting bracket to hollow walls (wall areas between studs) or to solid walls (concrete or masonry).

Decide which method better suits your needs. Either method will provide a secure hold for the mounting bracket.

Marking Screw Locations

1.Tape mounting bracket to wall where heater will be located. Make sure mounting bracket is level.

WARNING: Maintain minimum clearances shown in Figure 11. If you can, provide greater clearances from floor and joining wall.

2.Mark screw locations on wall (see Figure 11).

Note: Only mark last hole on each end of mounting bracket. Insert mounting screws through these holes only.

3.Remove tape and mounting bracket from wall.

11"

16"

Min.

 

AdjoiningWall

 

Only Insert Mounting

18 3/4"

Screws Through Last

Min.

Hole On Each End

 

Floor

Figure 11 - Mounting Bracket Clearances

Attaching Mounting Bracket To Wall

Note: Wall anchors, mounting screws, and spacers are in hardware package. The hardware package is provided with heater.

Attaching To Wall Stud Method

For attaching mounting bracket to wall studs.

1. Drill holes at marked locations using 9/64" drill bit.

2. Place mounting bracket onto wall. Line up last hole on each end of bracket with holes drilled in wall.

3. Insert mounting screws through bracket and into wall studs.

4. Tighten screws until mounting bracket is firmly fastened to wall studs.

For morevisit www..com

109889

Image 9
Contents 15,000 to 30,000 Btu/Hr With Thermostat What to do if YOU Smell GASSafety Information Table of ContentsLocal Codes Product IdentificationUnpacking Assembling Heater Product FeaturesAIR for Combustion and Ventilation AssemblyAttaching Brass Front Trim to Front Panel Assembling and Attaching Brass TrimDetermining FRESH-AIR Flow for Heater Location Providing Adequate VentilationUnusually Tight Construction Confined and Unconfined SpaceVentilation AIR Ventilation Air From Inside BuildingVentilation Air From Outdoors Installation Items InstallationCheck GAS Type Locating HeaterInstallation Options Thermostat Sensing BulbMounting Heater to Wall Installing Bottom Mounting Screws Mounting Heater on Optional Hearth BasePlacing Heater On Mounting Bracket Securing Hearth Base to Floor Mounting Heater to Optional Hearth BaseSee Instructions Included With Mantel Kit Assembling Mantel Internally-tinned copper tubing may be used in cer Connecting to GAS SupplyPressure Testing Gas Supply Piping System Pressure Testing Heater Gas ConnectionsChecking GAS Connections For Your Safety Read Before Lighting Operating HeaterLighting Instructions Inspecting Burner Cleaning Burner Injector Holder and Pilot AIR Inlet Hole Cleaning MaintenanceCabinet Air PassagewaysObserved Problem Possible Cause Remedy TroubleshootingMaintenance, Observed Problem Possible Cause Replacement Parts SpecificationsService Hints Technical ServiceAccessories RFN30TA RFP30TA VMH3000TNA VMH3000TPA Illustrated Parts BreakdownNJF-8C Parts ListFBD Parts CentralsOwners Registration Form Postage Required 109889 Not a UPC

VMH3000TPA specifications

The Desa VMH3000TPA is a state-of-the-art heating appliance designed to deliver efficient warmth while ensuring user comfort and convenience. This model is widely recognized for its innovative technologies, smart design, and eco-friendly features, making it an ideal choice for residential spaces.

One of the standout features of the VMH3000TPA is its powerful heating capacity. With a robust output of 30,000 BTUs, it is engineered to heat large areas effectively, making it perfect for living rooms, open-plan spaces, or even workshops. Users can expect a consistent and reliable warmth throughout the chilly seasons, enhancing home comfort while reducing reliance on traditional heating systems.

The VMH3000TPA incorporates advanced heating technology, including a variable speed blower that allows for more efficient heat distribution. This feature ensures that warm air circulates evenly throughout the room, eliminating cold spots and creating a cozy atmosphere. Additionally, the unit has a programmable thermostat, allowing users to set and maintain their desired temperature easily.

For safety, the VMH3000TPA is equipped with multiple safety features, including an automatic shut-off function that activates if the unit overheats or tips over. This ensures peace of mind, especially in households with children or pets. Its durable construction includes a fireproof casing and a heat-resistant glass front, designed to withstand high temperatures while maintaining an attractive appearance.

The Desa VMH3000TPA is also designed with energy efficiency in mind. It operates on propane or natural gas, providing a cleaner-burning alternative to traditional heating methods. This model complies with environmental regulations, helping to reduce carbon emissions while lowering energy costs.

Another remarkable aspect is its user-friendly interface, which includes remote control functionality. Users can conveniently adjust settings from a distance, enhancing usability and comfort. This modern appliance is not just a heating solution; it is a blend of technology and design, ensuring that it complements any home décor while providing effective heating solutions.

In summary, the Desa VMH3000TPA stands out in the heating appliance market for its powerful performance, intelligent features, energy efficiency, and safety standards, making it a worthy investment for modern households seeking comfort and reliability during the colder months.