Desa WMN20A, GWP20TA, GWP30TA Air For Combustion Ventilation, Providing Adequate Ventilation

Page 5

Air For Combustion

And Ventilation

WARNING: This heater shall not be installed in a confined space or unusually tight con- struction unless provisions are provided for adequate combus- tion and ventilation air. Read the following instructions to insure proper fresh air for this and other fuel-burning appliances in your home.

Today’s homes are built more energy efficient than ever. New materials, increased insulation and new construction methods help reduce heat loss in homes. Home owners weather strip and caulk around windows and doors to keep the cold air out and the warm air in. Dur- ing heating months, home owners want their homes as airtight as possible.

While it is good to make your home energy efficient, your home needs to breathe. Fresh air must enter your home. All fuel-burning ap- pliances need fresh air for proper combustion and ventilation.

Exhaust fans, fireplaces, clothes dryers and fuel burning appliances draw air from the house to operate. You must provide adequate fresh air for these appliances. This will insure proper venting of vented fuel-burning appli- ances.

PROVIDING ADEQUATE

VENTILATION

The following are excerpts from National Fuel Gas Code, ANSI Z223.1/NFPA 54, Section 5.3, Air for Combustion and Ventilation.

All spaces in homes fall into one of the three following ventilation classifications:

1.Unusually Tight Construction

2.Unconfined Space

3.Confined Space

The information on pages 5 through 7 will help you classify your space and provide adequate ventilation.

Unusually Tight Construction

The air that leaks around doors and windows may provide enough fresh air for combustion and ventilation. However, in buildings of un- usually tight construction, you must provide additional fresh air.

Unusually tight construction is defined as construction where:

a.walls and ceilings exposed to the outside atmosphere have a continuous water vapor retarder with a rating of one perm (6x10-11kg per pa-sec-m2) or less with openings gasketed or sealed and

b.weather stripping has been added on openable windows and doors and

c.caulking or sealants are applied to areas such as joints around window and door frames, between sole plates and floors, between wall-ceiling joints, between wall panels, at penetrations for plumbing, electrical and gas lines and at other open- ings.

If your home meets all of the three criteria above, you must provide additional fresh air. See Ventilation Air From Outdoors, page 7.

If your home does not meet all of the three criteria above, proceed to Determining Fresh-Air Flow For Heater Location, page 6.

Confined and Unconfined Space

The National Fuel Gas Code, ANSI Z223.1/ NFPA 54 defines a confined space as a space whose volume is less than 50 cubic feet per 1,000 Btu per hour (4.8 m3 per kw) of the ag- gregate input rating of all appliances installed in that space and an unconfined space as a space whose volume is not less than 50 cubic feet per 1,000 Btu per hour (4.8 m3 per kw) of the aggregate input rating of all appliances installed in that space. Rooms communicating directly with the space in which the appliances are installed*, through openings not furnished with doors, are considered a part of the un- confined space.

*Adjoining rooms are communicating only if there are doorless passageways or ventilation grills between them.

119344-01Bwww.desatech.com

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Models GWN20TA, GWP20TA, GWN30TA, GWP30TA, WMN20a, WMP20a What to do if YOU Smell GASSafety Information Table of ContentsSafety Information Product Features Safety InformationLocal Codes UnpackingProviding Adequate Ventilation Air For Combustion VentilationUnusually Tight Construction Confined and Unconfined SpaceDetermining if You Have a Confined or Unconfined Space AIR for Combustion VentilationDetermining FRESH-AIR Flow for Heater Location Ventilation AIR InstallationCheck GAS Type Ventilation Air From Inside BuildingInstallation Items InstallationLocating Heater This heater is designed to be mounted on a wallInstalling Heater to Wall 20,000 Btu/Hr Models 30,000 Btu/Hr ModelsAttaching To Wall Stud Method Attaching To Wall Anchor MethodMounting heater to floor With optional floor kit Installing Bottom Mounting ScrewsHeater Wall Mounting Base Feet to HeaterTypical Inlet Pipe Diameters Connecting to GAS SupplyTest Pressures Equal To or Less Than 1/2 Psig 3.5 kPa Checking GAS ConnectionsCorrect all leaks at once Pressure Testing Heater Gas ConnectionsOperating Heater For Your Safety Read Before LightingLighting Instructions Do not try to light any applianceOperating Heater Manual Lighting ProcedureTo Turn OFF GAS To Appliance Thermostat Control OperationBurner Flame Pattern Inspecting HeaterPilot Flame Pattern ODS/PILOT and Burner Cleaning MaintenanceBurner Pilot Air Inlet CabinetObserved Problem Possible Cause Remedy TroubleshootingTroubleshooting Slight smoke or odor during Observe minimum installaBlocked Burner orificeStatement above Gas leak. See WarningService Hints SpecificationsReplacement Parts Technical ServiceModels WMN20A, WMP20A, GWN20TA, GWP20TA, GWN30TA and GWP30TA Illustrated Parts BreakdownNJF 8C Parts ListEquipment Shutoff Valve GA5010 AccessoriesBase Kit GA4550 Electronic ignitor Kit GA435 Not ShownParts Centrals Keep this Warranty Warranty InformationModel Serial No Date of Purchase Industrial Drive P.O. Box 119344-01 Rev. B
Top Page Image Contents