Desa RCLP35B owner manual Continued, Service Procedures, Ignitor

Page 8
(Continued)

35,000 BTU/Hr CANADIAN PROPANE CONSTRUCTION HEATER

SERVICE

PROCEDURES

(Continued)

7.Place fan onto motor shaft.

IMPORTANT: When placing fan onto motor shaft, make sure part number stamped on fan is facing motor.

8.Attach fan nut to end of motor shaft. Tighten fan nut firmly.

9.Place motor and fan guard into rear of heater shell. Make sure power cord is properly located (see Figure 12).

Piezo

IGNITORTarget

Ignitor Wire

Bushing

 

 

Gap

 

Underside

 

Ignitor

 

of Heater

 

 

 

Base

 

Figure 13 - Removing Ignitor Wire from

Figure 15 - Clearance between Ignitor

Piezo Ignitor

Electrode and Target Plate

Figure 12 - Replacing Motor and Fan Guard into Heater

3.Remove ignitor mounting screw from rear head using nut-driver or standard screwdriver (see Figure 14).

Rear Head

Ignitor

Ignitor Manual background

Mounting

Manual backgroundWARNING: Make sure heater is disconnected from propane supply. Heater could ignite caus- ing severe burns.

Push piezo ignitor button and watch forspark between ignitor electrode and target plate.

9.Place motor and fan guard into rear of heater shell (see Motor, page 7, steps 9 and 10).

10.Insert three screws through heater shell and into fan guard. Tighten screws firmly.

IGNITOR

1.Remove motor and fan guard from heater (see Motor, page 7, steps 1 and 2).

2.Remove black ignitor wire from piezo ignitor. Access ignitor wire through underside of heater base (see Figure 13). Push wire up through bushing in heater shell.

Figure 14 - Removing Ignitor Mounting Screw and Ignitor

4.Remove ignitor from rear head.

5.Install new ignitor. Attach ignitor to rear head with ignitor mounting screw.

6.Run ignitor wire from new ignitor through bushing in heater shell. Attach ignitor wire to piezo ignitor.

7.Set gap between ignitor electrode and target plate to .17" (4.3 mm)

(see Figure 15).

8.Test for spark.

8

103907

Image 8
Contents CANADIAN PROPANE CONSTRUCTION HEATER Model RCLP35BWARNING NOT FOR HOME OR RECREATIONAL VEHICLE USE SAFETY INFORMATION WARNINGSWARNING FIRE, BURN, IN THEORY OF OPERATION PRODUCT IDENTIFICATIONUNPACKING PROPANE SUPPLY INSTALLATION VENTILATIONAverage Temp.F C No. Of TanksMAINTENANCE OPERATIONSTORAGE To Start HeaterTROUBLESHOOTING OBSERVED FAULTPOSSIBLE CAUSE REMEDYMOTOR SERVICE PROCEDURESELECTRICAL SYSTEM IGNITOR ContinuedSERVICE PROCEDURES SPECIFICATIONS TECHNICAL SERVICEREPLACEMENT PARTS ACCESSORIESILLUSTRATED PARTS BREAKDOWN PARTS LIST RCLP35BLIMITED WARRANTY WARRANTY AND REPAIR SERVICEDESA Industries of Canada, Inc Modèle RCLP35B MANUEL D’UTILISATIONAPPAREIL DE 35,000 BTU/Hr APPAREIL DE CHAUFFAGE AU PROPANE INFORMATIONS CONCERNANT LA SÉCURITÉMANUEL DUTILISATION INFORMATIONSIDENTIFICATION DU PRODUIT CONCERNANT LA SÉCURITÉINSTALLATION ALIMENTATION EN PROPANE35,000 BTU/Hr APPAREIL DE CHAUFFAGE AU PROPANE Alimentation en propaneFONCTIONNEMENT INSTALLATIONMANUEL DUTILISATION VENTILATIONREMISAGE ENTRETIEN35,000 BTU/Hr APPAREIL DE CHAUFFAGE AU PROPANE FONCTIONNEMENTDÉPANNAGE MANUEL DUTILISATIONPROBLÈ ME CAUSE POSSIBLEPROCÉDURES D’ENTRETIEN 35,000 BTU/Hr APPAREIL DE CHAUFFAGE AU PROPANECIRCUIT É LECTRIQUE MOTEURALLUMEUR suite VENTILATEUR suiteMANUEL DUTILISATION PROCÉDURES D’ENTRETIENACCESSOIRES CARACTÉRISTIQUES35,000 BTU/Hr APPAREIL DE CHAUFFAGE AU PROPANE Homologué U.LSERVICEPIÈCES TECHNIQUE DÉTACHÉES MANUEL DUTILISATIONPiè ces sous garantie Piè ces non couvertes par la garantieVUE ÉCLATÉE DES PIÈCES 35,000 BTU/Hr APPAREIL DE CHAUFFAGE AU PROPANEÉ crou du ventilateurLISTE DES PIÈCES MANUEL DUTILISATIONPIÈ CE N DE RÉ F35,000 BTU/Hr APPAREIL DE CHAUFFAGE AU PROPANE MANUEL DUTILISATION CONSERVER CETTE GARANTIE GARANTIE LIMITÉ E GARANTIE ET SERVICE APRÈS-VENTEDESA Industries of Canada, Inc