Samsung SDC3C801/XFA Check Before Installing, Before Using the Product, Important to Installer

Page 10

installing your dryer

CHECK BEFORE INSTALLING

Do not plug the power cord into the wall outlet before completing the dryer installation.

Check the appearance of the product for any damaged parts before starting the product installation.

If there are any parts that appear to be damaged, please contact your nearest Samsung Customer Service Center.

When moving the product, do not move the product by yourself.

Take care of the edges of the dryer as they can be sharp.

Do not install the dryer in a location exposed to frost. Cold water may damage the product.

Use the product indoors only.

Do not place the dryer on one side when lifting it, and do not move the dryer in such a way that the internal parts shake. This may result in damage to the internal parts of the product.

BEFORE USING THE PRODUCT

Check if there are any accessories remaining inside the drum.

Plug in the power cord just before operating the product.

Do not block the air inlet hole of the cooling grill at the front of the dryer.

Do not place inflammable objects near the dryer and keep the surroundings clean.

Keep the dryer level with the ground.

Do not remove the adjustable levelling feet of the dryer. They are necessary to keep the product level with the ground.

IMPORTANT TO INSTALLER

Please read the following instructions carefully before installing the dryer. These instructions should be kept for future reference.

WARNING REMOVE THE DOOR FROM ALL DISCARDED APPLIANCES TO AVOID THE DANGER OF A CHILD SUFFOCATING.

LOCATION CONSIDERATIONS

Because a condensing type has been adopted, which condenses and processes air inside the dryer, external ventilation is not required.

Therefore, The dryer can be installed and used in any location where the temperature is between 5 and 35 degrees centigrade, unlike a conventional dryer that requires an external exhaust system.

ALCOVE OR CLOSET INSTALLATION

To operate safely and properly, your new Dryer requires minimum clearances of:

Sides – 25 mm

Rear – 51 mm

Top – 25 mm

Front – 465 mm

If both the washing machine and a dryer are installed together, the front of the alcove or closet must have at least 465 mm unobstructed air opening.

10_ installing your dryer

SDC18809X-02805K-05_EN.indd Sec3:10

2013-07-04 ￿￿ 2:24:29

Image 10
Contents Condensing Dryer This manual is made with 100% recycled paperFeatures Super capacityImportant Safety Symbols and Precautions Safety informationWhat YOU Need to Know about Safety Instructions DeathSDC18809X-02805K-05EN.indd Sec14 2013-07-04 SDC18809X-02805K-05EN.indd Sec15 2013-07-04 SDC18809X-02805K-05EN.indd Sec16 2013-07-04 SDC18809X-02805K-05EN.indd Sec17 2013-07-04 Contents See Dryer Exterior Installing your dryerTools Needed for Installation PartsImportant to Installer Check Before InstallingBefore Using the Product Alcove or Closet InstallationElectrical Requirements GroundingInstallation Side by Side Final Installation ChecklistConnect the drain hose To the other hole Draining Water Without Using the Water TankConnecting the Drain Hose To the holeConnecting the drain hose Installation Stacking Install dryer and bracket on washerDoor Reversal Holer-Lever Overview of the Control Panel Operating Instructions, tipsCycle Selector Selection Button Delay EndMy Cycle Temp SelectionSignal OFF Child LockMY Cycle Delay ENDInterior Lamp Rack DRY Remarks MAX 1.5kgLoad the Dryer Properly Getting StartedCare and cleaning Cleaning the Filter Case Dumping Condensed WaterCleaning the Condenser Assembly Special laundry tips Special Laundry TipsTroubleshooting Check These Points if Your DRYER…Troubleshooting Error Display Meaning Solution Information CodesAppendix Fabric Care ChartWash Cycle Special Instructions Laundering Declaration of Conformity SpecificationsProtecting the Environment He drum illuminationCycle Chart  user optionConsumption Data Memo Questions or COMMENTS?