Quadra-Fire 32198A installation instructions Installation

Page 16

R

Cape Cod Wood Stove

INSTALLATION

MASONRY CHIMNEY

For the method of installation to a masonry chimney shown in Figures 10 & 11, (on page 17), it will be necessary to purchase an 8 inch inside diameter, 12 inch long section of prefabricated listed solid pack chimney to use as a thimble. Purchase a wall spacer, trim collar and a wall band manufactured to fit the chimney section you purchase.

The safety features of this system are twofold:

1)A 2" air space between the chimney section and combustible wall; and, 2) The 1" air space around the chimney connector as it passes through the chimney section to the chimney.

The location of the opening through the wall to the chimney must leave a minimum 18" vertical clearance between the connector pipe and the ceiling to prevent the ceiling from catching fire.

Measure as shown in Figure A below and cut an opening in the wall large enough to accommodate the outside dimension of the chimney section plus the minimum air space specified by its manufacturer. It may be necessary to cut the wall studs and install a header and a sill frame to maintain the wall support. The hole in the chimney must have at least an 8" diameter fire clay liner or equivalent secured with refractory mortar. If it is necessary to cut a hole in the chimney liner, use extreme care to keep it from shattering.

First, make the frame for the thimble, ensuring it is no smaller than 14" square, to maintain a 2" air space around the chimney section. Attach the wall spacer to the chimney side of the frame. Then insert the frame into the opening, toe nailing it to the wall studs. Install the wall band in the framing to secure the chimney section in place. Insert a single section of chimney connector into the chimney through the wall band, being sure it does not protrude into the chimney beyond the edge of the chimney flue lining. Apply high temperature furnace cement to the end of the chimney section and install it over the connector, through the wall spacer. Tighten the wall band to hold the chimney section firmly in place and against the chimney. Install the trim collar on the outside of the opening. Check to ensure there is a 1" air space between the connector and the chimney section. During installation ensure that a 2" air space to the wood framing is maintained. Do not fill this space with insulation. Insulation in this air space will cause a heat buildup which may ignite the wood framing.

FIGURE A

Wall

 

Opening

Center of Hole

 

Center Line

Center Line

Add center-line measurement to the depth of your floor protector. Mark this combined measurement at the correct wall location for your installation, maintaining minimum clearance to combustibles, and mark the wall for a 10" x 10" (254mm x 254mm) square hole. The center of the square hole should line up with the centerline of the rear vent flue pipe, as shown in Figure A above.

Page 16

32198A February 15, 2002

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Cape Cod Woodstove Cape Cod Wood Stove Welcome Contents Listings Listings & Code AprovalsSafety Label Label Location Back of StoveFront View DimensionsSide View TOP Vent Installations ClearancesRear Vent Installations Minimum Clearances to CombustiblesFloor Protection USA Minimum Floor ProtectorAccessories By the regulatory authority having jurisdictionInstallation Chimney Height RequirementsFlue & Venting Systems Venting SystemMasonry Chimney Installation Installation Chimney Connector Masonry CHIMNEY,Connection to a Masonry Fireplace Connection to a Metal Prefabricated Chimney Connection to AN Interior Metal Prefabricated Chimney Connection to AN Exterior Metal Prefabricated Chimney Mobile Home Installation Firebrick Placement AssemblyReversible Flue Collar Outside AIR KIT Installation Blower Installation & Operation Blower Operating InstructionsOperation PRE-USE CheckBurning PROCESS, Wood Selection and StorageAIR Controls Primary AIR SystemTable a Heat Output Settings Operating TipsBuilding a Fire BREAK-IN PeriodMaintenance ASH RemovalChimney Cleaning Creosote -- Formation and Need For RemovalChimney CLEANING, Glass Care & Replacement Door & Gasket Kaowool Insulating Baffle BlanketTroubleshooting Checklist Draft ProblemsTROUBLE- Shooting Trouble Shooting Flue DraftPlease Contact Your Dealer to Order Replacement Parts PartsWarranty Cape Cod Woodstove

32198A specifications

The Quadra-Fire 32198A is a highly regarded insert stove that offers an ideal solution for homeowners seeking efficient heating while enhancing the aesthetics of their living spaces. Renowned for its quality and performance, the Quadra-Fire 32198A enables users to enjoy warmth and ambiance, making it a valuable addition to any home.

One of the standout features of the Quadra-Fire 32198A is its exceptional heating efficiency. Designed with a powerful combustion system, this stove boasts an impressive efficiency rating, ensuring that a significant amount of the fuel's energy is converted into usable heat. This efficiency not only translates into lower fuel costs for users, but it also means reduced emissions, making it an environmentally friendly option for heating.

The stove incorporates advanced technologies to optimize its performance. The Quadra-Fire 32198A features the ingenious Quadra-Fire patented Four-Point Burn System. This system ensures complete combustion of wood, resulting in a cleaner burn and extended burn times. Moreover, the ceramic glass window allows for a beautiful view of the flickering flames while maintaining high thermal efficiency.

In terms of design, the Quadra-Fire 32198A is both stylish and functional. It comes with a sleek, modern aesthetic that can complement various interior design styles. Additionally, its compact size allows it to fit seamlessly into smaller spaces, making it an excellent choice for homes where space is at a premium.

Durability is another hallmark of the Quadra-Fire 32198A. Constructed from high-quality materials, this stove is built to withstand the rigors of regular use. The heavy-duty firebox enhances longevity and ensures that the stove remains functional and reliable over the years.

The user-friendly features of the Quadra-Fire 32198A set it apart from many competitors. With easy-to-use controls, homeowners can effortlessly adjust the heat output according to their needs. The simple ash removal system also adds convenience, allowing for hassle-free maintenance.

In conclusion, the Quadra-Fire 32198A is a remarkable wood insert stove that combines efficiency, advanced technology, and stylish design. Its innovative features, unparalleled performance, and durability make it a top choice for those looking to enhance their home's comfort while enjoying the warmth and beauty of a wood fire. Whether for a cozy evening or a chilly winter day, the Quadra-Fire 32198A is poised to deliver exceptional heating and ambiance for many years to come.
Top Page Image Contents