Quadra-Fire CB1200M-MBK owner manual Mobile Home, CB 1200 Pellet Stove

Page 17

 

R

CB 1200 Pellet Stove

 

 

 

 

 

 

 

 

 

6

Mobile Home

 

 

 

 

 

A. Mobile Home Installation

You must use a Quadra-Fire Outside Air Kit for installation in a mobile home.

1.An outside air inlet must be provided for the combustion air and must remain clear of leaves, debris, ice and/or snow. It must be unrestricted while the appliance is in use to prevent room air starvation which causes smoke spillage. Smoke spillage can also set off smoke alarms.

2.The combustion air duct system must be made of metal. It must permit zero clearance to combustible construction and prevent material from dropping into the inlet or into the area beneath the dwelling and contain a rodent screen.

3.The appliance must be secured to the mobile home structure by bolting it to the floor (using lag bolts) in two places. Use the same holes that secured the appliance to the shipping pallet.

4.The appliance must be grounded with #8 solid copper grounding wire or equivalent, terminated at each end with an NEC approved grounding device.

5.Refer to Clearances to Combustibles and floor pro- tection requirements on pages 9 & 10 for listings to combustibles and appropriate chimney systems.

6.Use silicone to create an effective vapor barrier at the location where the chimney or other component penetrates to the the exterior of the structure.

7.Follow the chimney manufacturer’s instructions when installing the vent system for use in a mobile home.

8.Installation shall be in accordance with the Manufactur- ers Home & Safety Standard (HUD) CFR 3280, Part 24.

WARNING

Installation must comply with Manufactured Home and Safety Standard (HUD), CFR 3280, Part 24.

CAUTION

THE STRUCTURAL INTEGRITY OF THE MANUFAC- TURED HOME FLOOR, WALL AND CEILING/ROOF MUST BE MAINTAINED.

Do NOT cut through:

•Floor joist, wall, studs or ceiling trusses.

•Any supporting material that would affect the structural integrity.

CAUTION

Never draw outside combustion air from:

•Wall, floor or ceiling cavity

•Enclosed space such as an attic or garage

 

Spark Arrestor Cap

Storm Collar

 

 

Roof Flashing

Joist Shield/Firestop

Approved Class “L” o

 

 

“PL” Pellet Vent

Figure 17.1

WARNING

NEVER INSTALL IN A SLEEPING ROOM.

December 16, 2011

7014-179D

Page 17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Hot glass will cause burns CB1200M-MBK007C Testing Lab & Report Number Serial Number Model Mfg DateCB 1200 Pellet Stove Table of Contents Listing and Code Approvals Appliance Location Design, Installation & Location Consider- ationsGetting Started Negative Pressure CB 1200 Pellet Stove Locating Your Appliance & ChimneyThermostat Location DraftInspect Appliance & Components and Pre-Burn Check List CB 1200 Pellet Stove Fire SafetyTools And Supplies Needed Appliance Dimensions 3Dimensions and ClearancesCB 1200 Pellet Stove Clearances to Combustibles UL and ULC Alcove InstallationCB 1200 Pellet Stove Hearth Pad Requirements UL and ULC Exception for Horizontal InstallationsVenting Termination Requirements 4Vent InformationRChimney and Exhaust Connection Example of 3 Elbow-Rear Vent Termination Calculaton Pipe Selection ChartCB 1200 Pellet Stove Equivalent Feet of Pipe Alcove Venting SystemsCB 1200 Pellet Stove Through The Wall Straight OutDegree Through The Wall & Vertical External Vertical Internal Typical InstallationCB 1200 Pellet Stove Vertical into Existing Class a Chimney Alternate Masonry CB 1200 Pellet Stove MasonryMobile Home Rear Installation Floor InstallationAppliance Set-Up Outside Air Kit InstructionsRear Vent and Rear Vent to Top Vent Adapter Installation CB 1200 Pellet Stove Top Vent Adapter InstallationInstalling the Top Vent Adapter See FigureBrick Clip Installation CB 1200 Pellet Stove Optional Brick Set InstallationTop Log, Left Installing LogoRight Front Log Holes. See FigureThermostat Installation CB 1200 Pellet Stove Door InstallationTo install door To adjust latchesFuel Size And Material General Operating Information Operating InstructionsFeed Rate Adjustment Instructions Fire CharacteristicsCB 1200 Pellet Stove Before Your First Fire Starting Your First FireCB 1200 Pellet Stove Ignition Cycles Frequently Asked QuestionsSymptom TroubleshootingPage Page Frequency Daily Weekly Monthly Quick Reference Maintenance ChartTypes of Fuel Cleaning Ash Pan Cleaning Firepot with Cleaning Rod & Firepot ScraperCleaning Heat Exchanger Chambers & Drop Tube Ash Removal from FireboxCleaning Exhaust Path Cleaning Beneath Heat ExchangerCleaning the Glass Cleaning the HopperPreparing Firebox for Non-Burn Season Frequency Yearly Cleaning the Top Vent AdapterConvection Blower Replacement CB 1200 Pellet Stove High Ash Fuel Content MaintenanceRe-install blower to blower housing Exhaust Blower Replacement Remove existing blowerInstall new blower Replacing Side Glass Screws Replacing Center GlassComponent Function & Location Reference MaterialsCB 200 Pellet Stove Wiring Harness See .1 below Vacuum SwitchThermostat Snap Disc #1 Convection Blower 145FCB 1200 Pellet Stove Component Locations Part number list on following CB 1200 Pellet Stove Exploded Views#1 Top Assembly CB 1200 Pellet Stove Service Parts & Accessories#2 Baffle Assembly StockedStocked at Depot #10 Firepot Assembly and Associated Parts#11 Door Assembly LVGRL-CB12-BK-B 39.1 39.8 #39 Feed Motor AssemblyDescription Comments Part Number Accessories CB 1200 Pellet Stove Warranty Policy December 16 7014-179D Contact Information

CB1200M-MBK specifications

The Quadra-Fire CB1200M-MBK is a remarkable addition to the lineup of high-efficiency wood stoves, designed to provide exceptional heating performance while maintaining a user-friendly interface and aesthetic appeal. Known for its sleek design and modern technology, the CB1200M-MBK stands out as a powerful solution for both environmentally conscious homeowners and those in search of reliable warmth during cold months.

One of the main features of the CB1200M-MBK is its high efficiency rating, often exceeding 75%. This impressive figure is attributed to its innovative combustion technology, which maximizes wood-burning efficiency by promoting complete combustion. This means more heat is generated from less wood, translating to reduced emissions and less frequent refueling. This efficient design not only benefits the environment but also provides a cost-effective heating solution.

The CB1200M-MBK is equipped with a large firebox that can accommodate logs up to 18 inches long, allowing users to enjoy extended burn times and consistent heat output. With a capacity of up to 70,000 BTUs, this stove can efficiently heat spaces ranging from 1,000 to 2,200 square feet, making it suitable for a variety of home sizes.

Another standout feature is its advanced air control system, which provides precise control over combustion levels. This system enables users to adjust the air intake to optimize the fire's intensity, ensuring both comfort and efficiency. Additionally, the stove comes with a built-in ash pan, making cleanup easier and enhancing the overall user experience.

The CB1200M-MBK also showcases an appealing aesthetic, featuring a clean, modern design with a traditional cast-iron appearance. The durable, black finish offers an elegant touch, making it a stylish focal point in any room. Moreover, this model is designed to be compatible with various installation options, including top or rear venting, providing flexibility depending on the specific needs of the home.

Durability is another hallmark of the CB1200M-MBK, constructed with high-quality materials that ensure longevity and performance. The heavy-duty steel construction and quality ceramic glass withstand high temperatures and resist cracking, promising years of reliable use.

In conclusion, the Quadra-Fire CB1200M-MBK is a perfect blend of efficiency, performance, and style. With its impressive BTU output, advanced combustion technology, and user-friendly design, it stands as an ideal choice for homeowners looking to enhance their heating solutions while being mindful of environmental impacts.
Top Page Image Contents