CB 1200 Pellet Stove Door Installation | Quadra-Fire CB1200M-MBK

CB 1200 Pellet Stove

I. Door Installation

To install door:

1.Carefully remove door from packaging.

2.Line up hinges with hinge pins on appliance body, and slide door down until it sits securely on pins. Figure 22.1.

3.If door is plated, be sure to clean all plated surfaces and glass with a glass cleaner to ensure all oils are removed before your first burn.

4.Remove all labels from glass before burning appliance.

To adjust latches:
1.	Close door securely.
2.	Place rod in slot on the bracket on the door and close
	latch.
3.	Latch must close tightly enough to ensure an airtight
	seal between the door and the body of the appliance. To
	increase tension on the latch, turn the rod clockwise a few
	turns, then attempt to close the latch, until it is snug. Do not
	overtighten; you should be able to close the latch with your
	hand. Figure 22.2.
4.	After adjusting the latch, place a Phillips head screw driver
	in the end of the rod, and tighten the nut with a wrench.
	This will maintain the correct tension on the rod and latch.

Hinge Pin

Hinge

Figure 22.1

Rod and nut

Figure 22.2

J. Thermostat Installation

1. A 12 volt AC thermostat is required to operate this pellet appliance. You may use the included wall mount thermo- stat or purchase an optional programmable thermostat or remote control. It is equipped with an adjustable heat anticipator. The current rating is .05 amps. The anticipator needs to be adjusted to the lowest setting available.

2.When mounting a thermostat on a wall, be sure to follow your thermostat installation instructions carefully.

NOTE: Thermostat must be mounted level for accurate readings. The thermostat should be mounted on an inside wall and not in direct line with the appliance convection air.

NOTE: If the thermostat is located too close to the appliance, you may need to set the temperature setting slightly higher to maintain the desired temperature in your home.

3.There is a 4 screw terminal block located on the back lower left corner of the stove directly above the power cord inlet. The center 2 screws are for the thermostat wires.

Power Outlet

Terminal Block.

Center 2 screws for

Thermostat Wires

Figure 22.3

CAUTION

Shock hazard.

• Do NOT remove grounding prong from plug.

•Plug directly into properly grounded 3 prong receptacle.

•Route cord away from appliance.

•Do NOT route cord under or in front of appli- ance.

Page 22

7014-179D

December 16, 2011

CB1200M-MBK specifications

The Quadra-Fire CB1200M-MBK is a remarkable addition to the lineup of high-efficiency wood stoves, designed to provide exceptional heating performance while maintaining a user-friendly interface and aesthetic appeal. Known for its sleek design and modern technology, the CB1200M-MBK stands out as a powerful solution for both environmentally conscious homeowners and those in search of reliable warmth during cold months.

One of the main features of the CB1200M-MBK is its high efficiency rating, often exceeding 75%. This impressive figure is attributed to its innovative combustion technology, which maximizes wood-burning efficiency by promoting complete combustion. This means more heat is generated from less wood, translating to reduced emissions and less frequent refueling. This efficient design not only benefits the environment but also provides a cost-effective heating solution.

The CB1200M-MBK is equipped with a large firebox that can accommodate logs up to 18 inches long, allowing users to enjoy extended burn times and consistent heat output. With a capacity of up to 70,000 BTUs, this stove can efficiently heat spaces ranging from 1,000 to 2,200 square feet, making it suitable for a variety of home sizes.

Another standout feature is its advanced air control system, which provides precise control over combustion levels. This system enables users to adjust the air intake to optimize the fire's intensity, ensuring both comfort and efficiency. Additionally, the stove comes with a built-in ash pan, making cleanup easier and enhancing the overall user experience.

The CB1200M-MBK also showcases an appealing aesthetic, featuring a clean, modern design with a traditional cast-iron appearance. The durable, black finish offers an elegant touch, making it a stylish focal point in any room. Moreover, this model is designed to be compatible with various installation options, including top or rear venting, providing flexibility depending on the specific needs of the home.

Durability is another hallmark of the CB1200M-MBK, constructed with high-quality materials that ensure longevity and performance. The heavy-duty steel construction and quality ceramic glass withstand high temperatures and resist cracking, promising years of reliable use.

In conclusion, the Quadra-Fire CB1200M-MBK is a perfect blend of efficiency, performance, and style. With its impressive BTU output, advanced combustion technology, and user-friendly design, it stands as an ideal choice for homeowners looking to enhance their heating solutions while being mindful of environmental impacts.