Quadra-Fire 7100FP-BK-B, 7100FP-NL-B Run Length Cut Pipe 20 40 ft 6-12m, 20 ft 3 6m 10 ft 1 3m

Page 34

R

7100FP EPA Woodburning Fireplace

INSTALLATION

1.Remove the knockout or cover plate from the top of the fireplace and discard it. See Figure 34.1.

2.Cut a 3 in. (76mm) hole in the insulation board as per the dimensions shown in Figure 34.1.

 

3-13/16 in.

 

 

 

 

 

 

(97mm)

 

 

 

 

 

3-1/8 in. (79mm)

 

 

 

 

 

 

C

Adapter

 

 

 

 

 

L

 

 

 

 

 

 

Mounting

 

 

 

 

 

 

Plate

 

 

 

 

 

 

Starter Pipe

 

 

Knockout

 

 

 

 

 

 

 

 

le

 

 

 

 

 

 

ho

 

 

 

 

 

.(76mm)

 

Cut

a

3

in

board

 

 

 

 

 

 

 

 

 

 

in

insulation

 

 

 

 

 

 

 

Figure 34.1

 

 

 

 

 

 

Figure 34.3

6.Slide the starter pipe into the fireplace, matching the holes in the plate to the holes in the fireplace.

7.Place the Adapter on the Mounting Plate lining up holes. Using the 4 sheet metal screws included in the kit, secure the Adapter and Mounting Plate into fireplace. After secur- ing to the fireplace, tape down the Adapter edges to the top of the fireplace with aluminum tape to prevent leakage.

8.Determine the location for the air register and fan housing assembly. Cut a 7-5/8 in. x 13-5/8 in. (143 x 346mm) hole between framing members (wall studs or floor joists). The brackets can be rotated 180° and mounted to the back side of the 2 x 4 if necessary. See Figure 35.2 on page 35.

3.Determine the necessary length of starter pipe from the following table and cut as required. See Figure 34.2.

4.The starter pipe is shipped flat. After cutting to the required length, manually roll the pipe together and snap lock into place. NOTE: It is important the pipe length be adhered to or it will affect the performance of your fireplace.

NOTE: The fan and electrical connections must be accessible for servicing per local code requirements.

NOTE: If the fan housing is installed in a 2 x 4 wall, the front of the housing will protrude approximately 1/4 in. (6mm) from the finished wall. See Figure 35.1 on page 35.

Run Length

Cut Pipe

20 - 40 ft (6-12m)

2 in. (51mm)*

*A minimum of 2 in. (51mm) pipe must be used to cover the raw insulation to prevent it tfrom blow-

 

ing out through the Return Air Grille.

10

- 20 ft (3 - 6m)

8 in. (203mm)

3

- 10 ft (1 - 3m)

No cut needed**

**Use full 16 in. (406mm) as supplied

Figure 34.2

5.On the Mounting Plate, hand bend the tabs downward. Slide the tabs over the outside of the starter pipe. Secure with 4 sheet metal screws included in fasteners package. Figure 34.3.

WARNING

Fire Risk

Comply with all minimum clearances speci- fied.

A minimum 1/2 in. (13mm) air clearance must be maintained at the back and 1 in. (25mm) to the sides of the fireplace assembly.

9.Attach enough 6 in. (152mm) B-Vent as required for your installation to the fan housing. A maximum of (4) 90° elbows is recommended. Securely twist lock the B-Vent to the Adapter.

Also screw the B-Vent to the outlet box on the fan housing. See Figure 35.2 on page 35. Support duct at intervals of no greater than 4 ft (1 m) as required by local code.

Page 34

433-1390D

September 7, 2007

Image 34
Contents 7100FP-BK-B 7100FP-GD-B 7100FP-NL-B Fire Risk007 7100FP EPA Woodburning FireplaceLocation on hang tag on right side of fireplace Table of Contents Appliance Certification Listing and Code ApprovalsMobile Home Approved 7100FP EPA Woodburning Fireplace Glass Specifications BTU & Efficiency SpecificationsNegative Pressure Design and Installation ConsiderationsGetting Started Asphyxiation RiskSeptember 7 433-1390D 7100FP EPA Woodburning Fireplace Typical Fireplace System Typical Fireplace SystemInspect Fireplace and Components 7100FP EPA Woodburning Fireplace Tools and Supplies NeededFire Risk Explosion Risk Selecting Fireplace Location Framing and ClearancesModel #7100FP 7100FP EPA Woodburning Fireplace Clearances Clearances to Combustible MaterialsNon-Combustible Materials Frame the FireplaceMinimum Clearances to Combustibles Combustible MaterialsElectrical Access and Wiring Diagram Suggestions7100FP EPA Woodburning Fireplace Construct the Chase MaterialsInstallation of Fireplace Install the Outside Air KitRisk of Smoke Spillage Fire Risk Asphyxiation RiskHandle Left Closed Handle Right Open Auxiliary Convection Air System Attic spaceConvection Air Lock Level the Fireplace 7100FP EPA Woodburning Fireplace Secure the FireplacePosition the Fireplace Place the Protective Metal Hearth StripsChimney Assembly 7100FP EPA Woodburning Fireplace Chimney Requirements Chimney Termination Requirements7100FP EPA Woodburning Fireplace Using Offsets/Returns ExampleAssembling Chimney Sections for the SL- 300 Series Assembling Chimney SectionsInstall the Ceiling Firestops Installing Flex PipeDouble-check the Chimney Assembly Secure the ChimneyChimney Termination Requirements See Figures 26.1 Complete the EnclosureChimney Termination 2-10-03 Rule Slanted RoofsMark the Exit Point of the Roof Install the Roof FlashingInstall the Chimney Air Kit required in Canada Cut Out the Hole in the RoofConsult local codes for framing details 7100FP EPA Woodburning Fireplace Chase Top Install the Termination CapChase Top Framing For installations utilizing a Round Telescoping Termination Blower Replacement Instructions AccessoriesBlower Replacement Blower Cord LocationDoor and Door Gasket Right Door7100FP EPA Woodburning Fireplace Heat Zone Kit Minimum Clearance to CombustiblesRun Length Cut Pipe 20 40 ft 6-12m 20 ft 3 6m 10 ft 1 3mBracket 7100FP EPA Woodburning Fireplace Timer Assembly Replacement Remove 2 screwsTimer Plate 7100FP EPA Woodburning FireplaceFinishing Hearth ExtensionModel # 7100FP Positioning the Protective Metal Hearth StripsOuter Can Flange Fascia Tile or Marble Combustible Floor Non-Combustible Sealant Material Finishing MaterialNon-Combustible Material Cardboard or Metal TemplateComplete installation Risk of Fire7100FP EPA Woodburning Fireplace Mantel Mantel SpecificationsGeneral Information Operating InstructionsKeep open during use Firescreen 7100FP EPA Woodburning Fireplace Outside AirClear Space Near the Fireplace Glass DoorsWood Fuel Hardwood vs. Softwood 7100FP EPA Woodburning Fireplace Blower OperationHeat Zone Operation Minimum Clearance to Combustible 1 in mm from the B-VentSeasoning 7100FP EPA Woodburning Fireplace Moisture contentStoring Wood 7100FP EPA Woodburning Fireplace Starting a Fire Final stage Kindling or 1st stage2nd stage Slide Air ControlBurn Rates Emissions, follow these operating procedures7100FP EPA Woodburning Fireplace Burning Guidelines Opacity For maximum operating efficiency with the lowestOverfiring Fire Safety Chimney FireUnderstanding Vent Problems TroubleshootingDraft Problems Factory-built Fireplaces Troubleshooting Diagnostic Question Possible Causes of Condition Solutions If I can’t get a good fire going, what am I doing wrong?Don’t get enough/any heat. What can I do about it? Maintenance and Servicing the Fireplace General MaintenanceDisposal of Ashes Glass ReplacementGlass Cleaning Fire Risk Injury RiskVide brick dimension or copy this page, mark the desired 7100FP EPA Woodburning Fireplace Brick ReplacementUse Part 832-2370 when ordering individual brick. Pro Brick and take it to your authorized dealerMaintenance Task List Inspect Maintenance TasksReference Materials Fireplace Dimensions7100FP FS338 14-1/2 368 mm FS339 18-3/8 467 mm 7100FP EPA Woodburning Fireplace Chimney ComponentsCatalog Description Catalog No FS340 16-3/4 425 mm15-3/4 Glass Size 12-3/50 w x 15 h 7100FP EPA Woodburning Fireplace Fireplace Diagram 17 13 1514 27 25 2124Part Description 7100FP EPA Woodburning Fireplace Service PartsAlphabetical Order Accessories RIVNUT-REPAIRLifetime Warranty 7100FP EPA Woodburning Fireplace Warranty PolicyContact Information 7100FP EPA Certified Woodburning FireplaceDealer Telephone

7100FP-BK-B, 7100FP-GD-B, 7100FP-NL-B specifications

The Quadra-Fire 7100FP series, including the models 7100FP-BK-B, 7100FP-NL-B, and 7100FP-GD-B, represents an exceptional choice for homeowners seeking efficient and powerful heating solutions. These fireplaces are designed to provide warmth and ambiance while incorporating advanced technologies that enhance performance and ease of use.

One of the primary features of the 7100FP series is its large viewing area, which allows homeowners to enjoy the mesmerizing flames while increasing the aesthetic appeal of any living space. The generous size of the firebox ensures that it can accommodate sizable logs, providing longer burn times and requiring less frequent reloading. This feature is particularly beneficial for those who appreciate an extended, leisurely evening by the fire.

A hallmark of the Quadra-Fire brand is its innovative heating technology. The 7100FP models are equipped with the patented Quadra-Fire combustion system, which promotes a cleaner burn and maximizes heat output. This system utilizes secondary combustion technology that burns off excess gases and particulates, resulting in a more environmentally friendly fire that emits fewer emissions compared to traditional wood-burning fireplaces.

Additionally, the 7100FP series includes advanced airflow designs that facilitate efficient heat distribution throughout the room. The adjustable air control allows users to easily regulate the burn rate and heat output, ensuring optimal comfort at any time. With a variety of trim options available, including the sleek black, traditional natural, and modern gold finishes, homeowners have the flexibility to choose a model that complements their interior decor.

Moreover, the 7100FP series is designed with user convenience in mind. For easy cleaning and maintenance, they include a removable ash pan feature. A glass viewing window is treated with a special coating, preventing soot buildup and allowing for uninterrupted views of the flames.

In terms of safety, the 7100FP units are equipped with a tempered glass door that is designed to withstand high temperatures, ensuring that the fireplace is safe for family gatherings. Overall, the Quadra-Fire 7100FP-BK-B, 7100FP-NL-B, and 7100FP-GD-B models seamlessly combine style, efficiency, and comfort, making them a top choice for those seeking a modern solution to home heating. With innovative technology and a commitment to performance, these fireplaces enhance any home’s ambiance while providing reliable warmth.