Quadra-Fire 7100FP-BK-B 7100FP EPA Woodburning Fireplace Blower Operation, Heat Zone Operation

Page 46

R

7100FP EPA Woodburning Fireplace

F. Blower Operation

Instructions with Blower Override Switch in manual posi- tion.

1.Initial (cold) Startup: Leave blower off until your fire- place is hot and a good coal bed is established, ap- proximately 30 minutes after fuel is lit.

2.High Burn Setting: The blower may be left on throughout the burn.

3.Medium or Medium High Burn Setting: The blower should be left off until a good burn is established, then turned on medium or high rate.

4.Low Burn Setting: The blower tends to cool off the fireplace. Leave blower off until the burn is well estab- lished; then, if you wish, turn the blower on at a low rate.

NOTE: The blower is equipped with a snap disc that will turn the blower on and off depending on the temperature of the fireplace. If the blower is not coming on at the desired time, flip the override switch to manual and operate the blower as described above.

The override switch and the blower speed control are hard wired at time of installation and installed in a standard wall mount with junction box on the wall.

G. Heat Zone Operation

The Heat-Zone accessory kit conveys warm air from the fireplace through air duct(s) to remote locations in the same room or other rooms of the building. You may install 1 or 2 Heat-Zone kits on the fireplace. Follow the instructions that is supplied with the kit. Installation of this kit MUST be performed by a qualified service technician. If any parts are missing or damaged, contact your local dealer before starting installation. DO NOT install a damaged kit.

The Heat-Zone kit is carefully engineered and must be installed only as specified. If you modify it or any of its com- ponents, you will void the warranty and you may possibly cause a fire hazard. Installation must be done according to applicable local, state, provincial, and/or national codes.

DUCT RUN REQUIREMENTS

MAXIMUM Duct Run = 40 ft. (12m)

MINIMUM Duct Run = 36 in. (914mm)

DUCTING MATERIAL

6 in. (152mm) B-Vent Only

DO NOT DUCT into existing furnace plenum

MINIMUM CLEARANCE TO COMBUSTIBLE 1 in. (25mm) from the B-Vent

1/2 in. (13mm) from top and bottom of outlet box 0 in. (0mm) from the sides of outlet box

12 in. (305mm) from wall register to ceiling

CAUTION

ALL wiring should be done by a qualified electrician and shall be in compliance with local codes and with the National Electric Code NFPA/NEC No. 70-current (in the United States), or with the current CSC22.1 Canadian Electric Code (in Canada).

H. Wood Fuel

Hardwood vs. Softwood

Your fireplace’s performance depends a great deal on the quality of the firewood you use. Contrary to popular belief, one species of wood varies very little to the other in terms of energy content. All seasoned wood, regardless of species, contains about 8,000 BTU’s per pound. The important factor is that hardwoods have a greater density than softwoods. Therefore, a piece of hardwood will con- tain about 60% more BTU’s than an equal size piece of softwood. Since firewood is commonly sold by the cord (128 cu. ft) a volume measurement, a cord of seasoned oak (hardwood) would contain about 60% more potential energy than a cord of seasoned pine (softwood).

There are many definitions of hardwood and softwood. Although not true in every case, one of the most reli- able is to classify them as coniferous or deciduous. Softwoods are considered coniferous. These are trees with needle-like leaves that stay green all year and carry their seeds exposed in a cone. Examples of softwood trees are Douglas fir, pine, spruce and cedar. Softwoods, being more porous, require less time to dry, burn faster and are easier to ignite than hardwoods. Deciduous trees are broadleaf trees that lose their leaves in the fall. Their seeds are usually found within a protective pod or enclosure. Hardwoods fall into this category. Some examples of deciduous trees are oak, maple, apple, and birch. However, it should be noted that there are some deciduous trees that are definitely not considered hardwoods such as poplar, aspen and alder. Hardwoods require more time to season, burn slower and are usually harder to ignite than softwoods. Obviously, you will use the type of wood that is most readily available in your area. However, if at all possible the best arrangement is to have a mix of softwood and hardwood. This way you can use the softwood for starting the fire giving off quick heat to bring the appliance up to operating temperature. Then add the hardwood for slow, even heat and longer burn time.

Page 46

433-1390D

September 7, 2007

Page 45 Page 47
Image 46
Page 45 Page 47
Contents 7100FP-BK-B 7100FP-GD-B 7100FP-NL-B Fire Risk007 7100FP EPA Woodburning FireplaceLocation on hang tag on right side of fireplace Table of Contents Appliance Certification Listing and Code ApprovalsMobile Home Approved 7100FP EPA Woodburning Fireplace Glass Specifications BTU & Efficiency SpecificationsNegative Pressure Design and Installation ConsiderationsGetting Started Asphyxiation RiskSeptember 7 433-1390D 7100FP EPA Woodburning Fireplace Typical Fireplace System Typical Fireplace SystemInspect Fireplace and Components 7100FP EPA Woodburning Fireplace Tools and Supplies NeededFire Risk Explosion Risk Selecting Fireplace Location Framing and ClearancesModel #7100FP 7100FP EPA Woodburning Fireplace Clearances Clearances to Combustible MaterialsNon-Combustible Materials Frame the FireplaceMinimum Clearances to Combustibles Combustible MaterialsElectrical Access and Wiring Diagram Suggestions7100FP EPA Woodburning Fireplace Construct the Chase MaterialsInstallation of Fireplace Install the Outside Air KitRisk of Smoke Spillage Fire Risk Asphyxiation RiskHandle Left Closed Handle Right Open Auxiliary Convection Air System Attic spaceConvection Air Lock Level the Fireplace 7100FP EPA Woodburning Fireplace Secure the FireplacePosition the Fireplace Place the Protective Metal Hearth StripsChimney Assembly 7100FP EPA Woodburning Fireplace Chimney Requirements Chimney Termination Requirements7100FP EPA Woodburning Fireplace Using Offsets/Returns ExampleAssembling Chimney Sections for the SL- 300 Series Assembling Chimney SectionsInstall the Ceiling Firestops Installing Flex PipeDouble-check the Chimney Assembly Secure the ChimneyChimney Termination Requirements See Figures 26.1 Complete the EnclosureChimney Termination 2-10-03 Rule Slanted RoofsMark the Exit Point of the Roof Install the Roof FlashingInstall the Chimney Air Kit required in Canada Cut Out the Hole in the RoofConsult local codes for framing details 7100FP EPA Woodburning Fireplace Chase Top Install the Termination CapChase Top Framing For installations utilizing a Round Telescoping Termination Blower Replacement Instructions AccessoriesBlower Replacement Blower Cord LocationDoor and Door Gasket Right Door7100FP EPA Woodburning Fireplace Heat Zone Kit Minimum Clearance to CombustiblesRun Length Cut Pipe 20 40 ft 6-12m 20 ft 3 6m 10 ft 1 3mBracket 7100FP EPA Woodburning Fireplace Timer Assembly Replacement Remove 2 screwsTimer Plate 7100FP EPA Woodburning FireplaceFinishing Hearth ExtensionModel # 7100FP Positioning the Protective Metal Hearth StripsOuter Can Flange Fascia Tile or Marble Combustible Floor Non-Combustible Sealant Material Finishing MaterialNon-Combustible Material Cardboard or Metal TemplateComplete installation Risk of Fire7100FP EPA Woodburning Fireplace Mantel Mantel SpecificationsGeneral Information Operating InstructionsKeep open during use Firescreen 7100FP EPA Woodburning Fireplace Outside AirClear Space Near the Fireplace Glass DoorsWood Fuel Hardwood vs. Softwood 7100FP EPA Woodburning Fireplace Blower OperationHeat Zone Operation Minimum Clearance to Combustible 1 in mm from the B-VentSeasoning 7100FP EPA Woodburning Fireplace Moisture contentStoring Wood 7100FP EPA Woodburning Fireplace Starting a Fire Final stage Kindling or 1st stage2nd stage Slide Air ControlBurn Rates Emissions, follow these operating procedures7100FP EPA Woodburning Fireplace Burning Guidelines Opacity For maximum operating efficiency with the lowestOverfiring Fire Safety Chimney FireUnderstanding Vent Problems TroubleshootingDraft Problems Factory-built Fireplaces Troubleshooting Diagnostic Question Possible Causes of Condition Solutions If I can’t get a good fire going, what am I doing wrong?Don’t get enough/any heat. What can I do about it? Maintenance and Servicing the Fireplace General MaintenanceDisposal of Ashes Glass ReplacementGlass Cleaning Fire Risk Injury RiskVide brick dimension or copy this page, mark the desired 7100FP EPA Woodburning Fireplace Brick ReplacementUse Part 832-2370 when ordering individual brick. Pro Brick and take it to your authorized dealerMaintenance Task List Inspect Maintenance TasksReference Materials Fireplace Dimensions7100FP FS338 14-1/2 368 mm FS339 18-3/8 467 mm 7100FP EPA Woodburning Fireplace Chimney ComponentsCatalog Description Catalog No FS340 16-3/4 425 mm15-3/4 Glass Size 12-3/50 w x 15 h 7100FP EPA Woodburning Fireplace Fireplace Diagram 17 13 1514 27 25 2124Part Description 7100FP EPA Woodburning Fireplace Service PartsAlphabetical Order Accessories RIVNUT-REPAIRLifetime Warranty 7100FP EPA Woodburning Fireplace Warranty PolicyContact Information 7100FP EPA Certified Woodburning FireplaceDealer Telephone

7100FP-BK-B, 7100FP-GD-B, 7100FP-NL-B specifications

The Quadra-Fire 7100FP series, including the models 7100FP-BK-B, 7100FP-NL-B, and 7100FP-GD-B, represents an exceptional choice for homeowners seeking efficient and powerful heating solutions. These fireplaces are designed to provide warmth and ambiance while incorporating advanced technologies that enhance performance and ease of use.

One of the primary features of the 7100FP series is its large viewing area, which allows homeowners to enjoy the mesmerizing flames while increasing the aesthetic appeal of any living space. The generous size of the firebox ensures that it can accommodate sizable logs, providing longer burn times and requiring less frequent reloading. This feature is particularly beneficial for those who appreciate an extended, leisurely evening by the fire.

A hallmark of the Quadra-Fire brand is its innovative heating technology. The 7100FP models are equipped with the patented Quadra-Fire combustion system, which promotes a cleaner burn and maximizes heat output. This system utilizes secondary combustion technology that burns off excess gases and particulates, resulting in a more environmentally friendly fire that emits fewer emissions compared to traditional wood-burning fireplaces.

Additionally, the 7100FP series includes advanced airflow designs that facilitate efficient heat distribution throughout the room. The adjustable air control allows users to easily regulate the burn rate and heat output, ensuring optimal comfort at any time. With a variety of trim options available, including the sleek black, traditional natural, and modern gold finishes, homeowners have the flexibility to choose a model that complements their interior decor.

Moreover, the 7100FP series is designed with user convenience in mind. For easy cleaning and maintenance, they include a removable ash pan feature. A glass viewing window is treated with a special coating, preventing soot buildup and allowing for uninterrupted views of the flames.

In terms of safety, the 7100FP units are equipped with a tempered glass door that is designed to withstand high temperatures, ensuring that the fireplace is safe for family gatherings. Overall, the Quadra-Fire 7100FP-BK-B, 7100FP-NL-B, and 7100FP-GD-B models seamlessly combine style, efficiency, and comfort, making them a top choice for those seeking a modern solution to home heating. With innovative technology and a commitment to performance, these fireplaces enhance any home’s ambiance while providing reliable warmth.
Top Page Image Contents