Quadra-Fire QVI-35FB-S owner manual Placing, Securing and Leveling the Appli- ance

Page 22

CUT AND BEND

FLASHING AS NEEDED

TO FIT CHIMNEY

SEALANT

ADHESIVE

Figure 8.2

•Trim chimney top plate to minimize excess overhang or bend over flue tile (see Figure 8.2).

•Place 3/8 inch bead of 300º F silicone on flue tile top.

D.Placing, Securing and Leveling the Appli- ance

•Install insert (without surround attached) into existing fireplace while pulling collar slide plate forward.

•Install gas line into hole provided on insert side.

•If applicable install remote control wires into insert side (see Section 8.E).

•Secure the air passage slide plate to the appliance by driving a #8 screw from the side plate bracket into the air passage slide plate.

•Level the appliance from side to side and front to back. If necessary, use the leveling legs included with the manual bag to set each corner of the base.

AIR PASSAGE

SLIDE PLATE

SLIDE PLATE

HANDLE

#8 SCREW

SLIDE PLATE BRACKET

•Position any excess flexible vent pipe back up into chimney without sagging. Twist and push flex vent together to shorten.

•Attach surround. Follow instructions accompanying surround.

•Push insert so that surround becomes tight against face of fireplace.

WARNING! Risk of Fire! Only an approved Hearth & Home Technologies surround may be used to cover inte- gral grills on solid fuel burning fireplaces. No other com- ponents such as shrouds, sheetmetal plates, etc., may be used to seal off vents.

WARNING! Risk of Explosion! Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this appliance may result in property damage or personal injury.

WARNING! Risk of Explosion/Combustion Fumes! Connect vent sections per installation instructions.

•The 3 foot section of stainless steel flexible pipe MUST be attached directly to the exhaust collar on the collar slide plate.

•Connect exhaust vent pipe ONLY to exhaust starting collar and termination cap center collar.

•Connect inlet air vent ONLY to inlet air collar on appliance and either the termination cap inlet air collar OR terminate within chimney.

•DO NOT allow vent to sag below connection point to appliance.

E. Remote Control

The receiver for the remote may be installed between the base pan of the insert and the firebox of the wood-burning fireplace as shown below or in the control cavity to the left of the valve.

EXISTING SIDE

REFRACTORY

REMOTE

RECEIVER

UNIT

EXISTING BOTTOM OF

FIREPLACE

Figure 8.3 Slide Plate Components

Figure 8.4

22

Quadra-Fire • QVI-35FB-S • 2178-900 Rev. B • 12/08

Page 21 Page 23
Image 22
Page 21 Page 23
Contents What to do if you smell gas Model QVI-35FB-SHOT Surfaces Homeowner Reference Information CongratulationsXxxxxxxx Table of Contents User GuideCONDITIONS, Exclusions & Limitation of Liability Limited Lifetime Warranty Listing and Code Approvals Operating Instructions User Guide Gas Fireplace SafetyYour Fireplace Clear Space Fixed Glass AssemblyRemote Controls, Wall Controls and Wall Switches Decorative Doors, Fronts and SurroundsFinal inspection by Standing Pilot IgnitionWhat to do if YOU Smell GAS Issue Solutions Frequently Asked QuestionsAfter Appliance is Lit Maintenance and Service Logs Maintenance Tasks-Service TechnicianGasket Seal and Glass Assembly Inspection FireboxStanding Pilot Flame Patterns Getting Started Typical Appliance SystemTypical System-Vent Pipe Tools and Supplies Needed Design and Installation ConsiderationsInspect Appliance and Components Minimum Fireplace Size Fireplace Size RequirementsMinimum Fireplace Opening QVI-35FB-SMantel and Wall Projections Clearances to Mantels or other Combustibles above ApplianceTermination Locations Vent Termination Minimum ClearancesInstallation Preparation Vent Limits Installing Vent Pipe and ApplianceConnecting Vent Pipe Venting ComponentsPlacing, Securing and Leveling the Appli- ance AIR Passage Slide Plate Handle #8 Screw Slide Plate BracketFactory Built Wood Burning Installing Adaptor and Termination CapMasonry Damper Flashing Kit OptionalGas Pressure Gas InformationFuel Conversion Gas ConnectionON/OFF Switch Wiring RequirementsStanding Pilot Ignition System Wiring Electrical InformationFan Replacement Junction Box InstallationOptional Accessories Variable Speed Control Junction BOX Blkblk BLK Finishing Appliance Setup Install the Log Assembly Log Set QVI35FB-S ShownLOG Number 2 SRV768-704 Position log #2 LOG Number 3 SRV768-705 Position log #3Quadra-Fire QVI-35FB-S 2178-900 Rev. B 12/08 Air Shutter Setting Air Shutter SettingsSymptom Possible Causes Corrective Action TroubleshootingStanding Pilot Ignition System Troubleshooting Symptom Possible Cause Corrective ActionModel Dimensions Appliance Dimension DiagramReference Materials Vent Kits Components Direct Vent Flex Liner KitsService Parts Log Set AssemblyPart number list on following Stocked Service Parts ListAt Depot QVI-35FB-S Contact Information

QVI-35FB-S specifications

The Quadra-Fire QVI-35FB-S is a state-of-the-art pellet stove designed to provide efficient heating while enhancing the aesthetic of any living space. With a sleek design and robust performance, this model stands out in the realm of home heating solutions.

One of the key features of the QVI-35FB-S is its impressive heating capacity. It can produce up to 35,000 BTUs, making it suitable for heating areas up to 1,600 square feet. This capability ensures that even larger spaces can be effectively warmed, providing consistent comfort during harsh winter months.

The stove’s clean-burning technology is another highlight. It utilizes a highly efficient combustion process, which not only maximizes heat output but also minimizes emissions. This environmentally conscious approach makes the QVI-35FB-S an excellent choice for eco-friendly homeowners who prioritize sustainability without sacrificing comfort.

The design of the QVI-35FB-S is both functional and stylish. It features a large viewing window framed by a sleek, contemporary design that allows for a full view of the flickering flames. This visual appeal is enhanced by the option of various finishes, allowing homeowners to choose a look that complements their interior décor.

Incorporating advanced features, the QVI-35FB-S includes an automated feed system and a programmable thermostat, providing users with greater control over their heating preferences. The automated feed ensures that the pellets are delivered consistently, maintaining a steady heat output. Meanwhile, the programmable thermostat allows for temperature adjustments throughout the day, promoting energy efficiency.

Safety is also a top priority in the design of the QVI-35FB-S. It comes equipped with a built-in safety shut-off system that activates in the event of overheating, providing peace of mind for users. Additionally, the stove includes a heat shield and other safety features to prevent accidents, making it a family-friendly option.

Installation is straightforward, thanks to the versatile venting options available with the QVI-35FB-S. Homeowners can choose direct vent installation, allowing for efficient exhalation of exhaust gases while drawing in fresh air from outside. This feature expands placement possibilities in various rooms.

Overall, the Quadra-Fire QVI-35FB-S combines modern design with superior performance and safety features, making it a compelling addition to any home heating system. Its blend of style, efficiency, and technology position it as a leader in the pellet stove market, meeting the diverse needs of today’s homeowners.
Top Page Image Contents