Monessen Hearth VWF36, VWF30, VWF18 manual Special Requirements

Page 54

SPECIAL REQUIREMENTS CONTINUED

2.APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as required in accordance with the above provisions shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certified.

3.SIGNAGE. A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight (8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The sign shall read, in print size no less than one-half (1/2) inch in size, “GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS.”

4.INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR 5.08(2)(a)1 through 4.

(b)EXEMPTIONS: The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4:

1.The equipment listed in Chapter 10 entitled “Equipment Not Required To Be Vented” in the most current edition of NFPA 54 as adopted by the Board; and

2.Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the dwelling, building or structure used in whole or in part for residential purposes.

(c)MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM PROVIDED. When the manufacturer of Product Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the instructions provided by the manufacturer for installation of the equipment and the venting system shall include:

1.Detailed instructions for the installation of the venting system design or the venting system components; and

2.A complete parts list for the venting system design or venting system.

(d)MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED. When the manufacturer of a Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the flue gases, but identifies “special venting systems,” the following requirements shall be satisfied by the manufacturer:

1.The identification of each “special venting system” shall include either the listing of the website, phone number or manufacturer's address where the venting system installation instructions can be obtained; and

2.The “special venting systems” shall be Product Approved by the Board, and the instructions provided with that system shall include a parts list and detailed installation instructions.

(e)A copy of all installation instructions for the Product Approved side wall horizontally vented gas fueled equipment and all the venting instructions, parts lists, and/or all design instructions for the venting system shall remain with the appli- ance or equipment at the completion of the installation.

Page 53 Page 55
Image 54
Page 53 Page 55
Contents Models VWF18 VWF24 VWF30 VWF36 Read and Save These InstructionsContents Important Safety Information InstallerOwner Safety Information Product SpecificationsMinimum Hearth Dimensions Minimum Opening Area of Chimney Damper for Venting Getting StartedMake Sure YOU have Received ALL Parts Minimum Chimney Height and Flue OpeningPlacement in a Fireplace with a Restrictive Barrier Height of Restriction Minimum Depth of Fireplace/FireboxInstallation Damper Stop InstallationBefore Installing the Appliance Operation to prevent overheating Installing Valve CoverCovers must be installed prior to Grate bar must not touch the valveWiring MILLI-VOLT Keep wiring away from heatSource and hot surfaces Connecting the GAS PipePressure Test Point Location Placement of Decorative Volcanic Rock LOG PlacementPlacement of Glowing Embers Rock Wool Filling the Burner PANPlacing Front Left Log #2 on Grate VWF24 Massive OAK Logs Sliding Shield Plate Down BackVWF30 Massive OAK Logs Centering Rear Log #1 on Grate BarsInstalling Right Middle Log #5 VWF30 Massive OAK LogsVWF36 Massive OAK Logs Sliding Shield Plate Down Back of Burner PanInstalling Right Side Middle Log #7 VWF36 Massive OAK LogsVWF18 American OAK Logs Placing Back Log #2 on GrateVWF24 American OAK Logs Placing Back Log #2 on Grate BarsVWF30 American OAK Logs Placing Front Log #2 on Front GrateVWF30 American OAK Logs Placing Left Crossover Log #7Notch Grate Prong Models VWF24 B 6 LogsModels VWF24/18 Split River OAK Placing Rear Log #1 on Back of GrateModels VWF24/18 Split River OAK Resting Top Right Log #4 onModels VWF30/24 Split River OAK Resting Top Right Log #4 on Bottom Left LogModels VWF30/24 Split River OAK Models VWF36/30 Split River OAK Sliding Shield Plate DownModels VWF36/30 Split River OAK Resting Center Top Log #7 BottomModels VWF18 Split Pine Placing Left Front Log #1A on GrateInstalling Right Log #6 Models VWF18 Split PineModels VWF24 Split Pine Placing Side Support Log #2 on Top Left of Log #1AInstalling Top Center Log #7 Models VWF24 Split PineModels VWF30 Split Pine Placing Side Support Log #2 on TopInstalling Right Middle Log #7 Models VWF30 Split PineModel VWF24/18WP Weathered Pine LOG Placing Rear Log #1 on Back GrateModel VWF24/18WP Weathered Pine LOG Placing Top Left Log #5 behind Rear LogModel VWF30/24WP Weathered Pine LOG Model VWF30/24WP Weathered Pine LOG Placing Top Center Log #7 on Rear LogModel VWF36/30WP Weathered Pine LOG Straddling V of Bottom Left LogModel VWF36/30WP Weathered Pine LOG Safety Instruction for Manual Control SPK Operating InstructionsWhat to do if YOU Smell GAS MILLI-VOLT Control Lighting Instructions Flame Appearance Checking Burner FlamesPilot Flame Appearance Fireplace Draft Test Fireplace Draft Test MethodRemote Control Receiver Replacement Cleaning and ServicingReplacement Parts AssemblyMassive OAK Logs VWF18MO VWF24MO VWF30MOAmerican OAK Logs Birch LogsSplit River OAK Logs VWF24/18SRO VWF30/24SRO VWF36/30SROSplit Pine Logs VWF18SPA and VWF24SPAWeathered Pine Logs Description Qty VWF24/18WPCarbon Monoxide Detector Requirements Special Requirements 27D8520 Lifetime Warranty Five Year Warranty
Top Page Image Contents