Monessen Hearth IDV380NVC, IDV490NVC Installation, ZERO-CLEARANCE Metal Fireplace Requirements

Page 10

IDV380/IDV490 Fireplace Insert

installation

ZERO-CLEARANCE (METAL) FIREPLACE REQUIREMENTS

•The damper and grate must be removed.

•The smoke shelf, internal baffles, screen, refractory and metal or glass doors may be removed (if applicable).

•Do not remove or alter the insulation or any structured rigid frame members (metal sides, floor, door frames, face of the fireplace, etc.).

WARNING

•Installer must attach red warning plate to the inside of the firebox of fireplace with screws supplied.

•Do not cut any sheet metal parts of the fireplace in which this gas fireplace insert is installed. THIS IS STRICTLY PROHIBITED!

•If factory-built fireplace has no gas access hole(s) provided, drill a 1.5" (37.5

mm)or less through lower sides or bottom of firebox. You must plug the access hole with noncombustible insulation after gas supply line has been installed.

•If your factory-built fireplace has air passages on the face for zero capabilities,

DO NOT BLOCK THESE PASSAGES!

 

 

Insulation

 

 

 

 

Smoke

Shelf

Damper

 

 

 

 

 

 

 

 

 

 

Doors

 

Masonry Lining or Refractory

 

Internal

 

 

 

 

Metal or Glass

 

 

 

 

Baffles

Screen

 

Grate

 

 

 

 

 

 

 

 

Masonry Lining or Refractory

 

Figure 6 -

Metal Fireplace Zero-Clearance Requirements

IMPORTANT: Please review the following carefully.

It is normal for inserts fabricated of steel to give off some expansion and/or contraction noises during the start up or cool down cycle. Similar noises are found with your furnace heat exchanger or car engine.

It is not unusual for your insert to give off some odor the first time it is burned. This is due to the curing of the paint and any undetected oil from the manufacturing process.

Please ensure that your room is well ventilated. OPEN ALL WINDOWS DURING INITIAL BURN OFF/CURING PHASE.

Burn your insert for at least six (6) hours on "HIGH" the first time you use it. Place the fan in the "OFF" position during this time.

10

57D0016

Page 9 Page 11
Image 10
Page 9 Page 11
Contents IDV Series Direct Vent Gas Fireplace Insert IDV380/IDV490 Fireplace Insert Installer Important Safety InformationOwner Important Safety Information and code approval Code ApprovalHigh Elevations Product featuresProduct Specifications GAS pressuresInsert dimensions IDV380 IDV490Installation Planning Installation InformationBefore You Start Clearances Mantel Clearances Hearth RequirementsInstallation Insert PlacementInstallation ZERO-CLEARANCE Metal Fireplace RequirementsInstallation Precautions Venting RequirementsVenting installation Altitude ConsiderationsVent Configurations Manifold Removal and Installation Installation items needed Insert InstallationInstalling gas piping to fireplace location Check gas typeInsert installation Propane/LPDo not use open flame to Check GAS PressureCheck for gas leaks Electrical Wiring Remote Wall mounted SwitchLog placement Installing Logs and Rock Wool Ember Material in FireboxPin on burner. Figure Top Y Log #7 Install Surround Surround installationInstalling On/Off switch Installing Filigree panels and cabi- net door frame Door and Filigree installationInstalling Doors Initial lighting What to do if YOU Smell GASNever use an open flame to check for gas leak Approved leak testing method Operating InstructionsLighting the burner Main burner switchAdjusting blower speed Pilot positionAIR Shutter Adjustment Natural GAS only Adjust the AIR ShutterGlass Replacement Venting system Cleaning and MaintenanceCleaning glass Pilot and burner flamesFirebox cleaning Maintaining your heater’s appearanceMaintenance Yearly service procedureTroubleshooting Blower Removal and Assembly Blower Parts ListReplacement Parts Replacement Parts IDV380NVC IDV380PVC IDV490NVC IDV490PVCIDV380/IDV490 Fireplace Insert IDV380/IDV490 Fireplace Insert Carbon Monoxide Detector Requirements Basic Warranty Lifetime WarrantyFive Year Warranty If Warranty Service is NeededEfficiency Ratings Mhsc
Related manuals
Manual 40 pages 49.26 Kb

IDV380NVC, IDV490NVC, IDV380PVC, IDV490PVC specifications

The Monessen Hearth IDV490NVC, IDV380PVC, IDV380NVC, and IDV490PVC represent a cutting-edge series of direct vent gas fireplaces that combine efficiency, style, and innovative technology. These models are designed to enhance home aesthetics while providing efficient heating solutions.

One of the standout features of the Monessen Hearth models is their impressive heating capabilities. The IDV490NVC and IDV490PVC are designed for larger spaces, providing up to 37,000 BTUs, while the IDV380NVC and IDV380PVC are suitable for medium-sized areas, delivering up to 30,000 BTUs. This makes each fireplace an ideal choice for various residential applications, accommodating different room sizes and heating needs.

The appliances employ advanced direct vent technology, allowing for safe operation by drawing air from outside for combustion and venting exhaust gases outside. This feature ensures that indoor air quality remains unaffected, making these models eco-friendly alternatives to traditional fireplaces. The efficient combustion process also means lower gas consumption, resulting in cost savings and a reduced environmental footprint.

Each model comes equipped with a variety of flame and control options. The realistic ceramic logs and glowing embers create an inviting ambiance, while the adjustable flame height allows users to customize their experience. Additionally, an easy-to-use remote control feature gives users the convenience of adjusting flames and temperature settings without leaving their seats.

The construction of these fireplaces is robust, featuring high-quality materials that ensure durability and longevity. The heat-resistant glass allows for an unobstructed view of the flames, adding a touch of elegance to any room.

Aesthetic choices further enhance personalization, as Monessen offers customizable options for surrounds and mantels that blend seamlessly with various interior styles.

In summary, the Monessen Hearth IDV490NVC, IDV380PVC, IDV380NVC, and IDV490PVC fireplaces exemplify modern heating technology combined with stylish design. Their powerful heat output, direct vent capabilities, user-friendly controls, and customizable aesthetics make them exceptional choices for homeowners looking to elevate their living spaces while ensuring comfort and efficiency. Whether for aesthetic appeal or functional heating, these models provide a perfect balance for any modern home.
Top Page Image Contents