Monessen Hearth IDV380PVC manual Insert Installation, Check gas type, Installation items needed

Page 15

INSERT INSTALLATION

IDV380/IDV490 Fireplace Insert

check gas type

Use proper gas type for the fireplace you are installing. If you have conflicting gas type, do not install fireplace. See dealer where you purchased the fireplace for proper fireplace according to your gas type.

Installing gas piping to fireplace location

WARNING

A qualified installer or service person must connect appliance to gas supply. Follow all local codes.

CAUTION

For propane/LP units, never connect fireplace directly to the propane/LP supply. This burner system requires an external regulator (not supplied). Install the external regulator between the burner system and propane/LP supply.

installation items needed

Make sure you have the items listed below before installing appliance.

External regulator (supplied by installer)

Piping (check local codes)

Test gauge connection*

Sealant (resistant to propane/LP gas)

Sediment trap (optional but recommended)

Tee joint

Pipe wrench

 

approved flexible gas line with gas connector (if allowed by local codes — not provided)

*A CSA design-certified equipment shutoff valve with 1/8" NPT tap is an acceptable alternative to test gauge connection. Purchase the CSA design-certified equipment shutoff valve from your dealer.

For propane/LP connections only, the installer must supply an external regulator. The external regulator will reduce incoming gas pressure. You must reduce incoming gas pressure to between 11 and 13 inches of wa- ter. If you do not reduce incoming gas pressure, burner system regulator damage could occur. Install external regulator with the vent pointing down as shown in Figure 14. Pointing the vent down protects it from freezing

rain or sleet.

External

100 gal. (min.

Propane/LP

Regual-

Supply Tank

tor

 

Vent

 

Pointing

 

Down

 

 

FP1930

 

Use only new black iron or steel pipe. Inter-

 

nally tinned copper or copper tubing can be

CAUTION

used per National Fuel Gas Code, Section

2.6.3, providing gas meets hydrogen sulfide

 

 

limits, and where permitted by local codes.

 

Gas piping system must be sized to provide

 

minimum inlet pressure (listed on data plate)

 

at the maximum flow rate (BTU/hr). Undue

 

pressure loss will occur if the pipe is too

 

small.

 

 

When using copper or flex connectors use only fittings approved for gas connections. The gas control inlet is 3/8" NPT.

Figure 14 -

External Regulator with Vent Pointing Down (Propane/LP Only)

57D0016

15

Image 15
Contents IDV Series Direct Vent Gas Fireplace Insert IDV380/IDV490 Fireplace Insert Important Safety Information InstallerOwner Code Approval Important Safety Information and code approvalGAS pressures Product featuresProduct Specifications High ElevationsIDV380 IDV490 Insert dimensionsInstallation Information Installation PlanningBefore You Start Mantel Clearances Hearth Requirements ClearancesInsert Placement InstallationZERO-CLEARANCE Metal Fireplace Requirements InstallationVenting Requirements Installation PrecautionsAltitude Considerations Venting installationVent Configurations Manifold Removal and Installation Check gas type Insert InstallationInstalling gas piping to fireplace location Installation items neededPropane/LP Insert installationCheck GAS Pressure Do not use open flame toCheck for gas leaks Remote Wall mounted Switch Electrical WiringInstalling Logs and Rock Wool Ember Material in Firebox Log placementPin on burner. Figure Top Y Log #7 Surround installation Install SurroundInstalling On/Off switch Door and Filigree installation Installing Filigree panels and cabi- net door frameInstalling Doors What to do if YOU Smell GAS Initial lightingNever use an open flame to check for gas leak Operating Instructions Approved leak testing methodPilot position Main burner switchAdjusting blower speed Lighting the burnerAdjust the AIR Shutter AIR Shutter Adjustment Natural GAS onlyGlass Replacement Pilot and burner flames Cleaning and MaintenanceCleaning glass Venting systemMaintaining your heater’s appearance Firebox cleaningYearly service procedure MaintenanceTroubleshooting Blower Parts List Blower Removal and AssemblyReplacement Parts IDV380NVC IDV380PVC IDV490NVC IDV490PVC Replacement PartsIDV380/IDV490 Fireplace Insert IDV380/IDV490 Fireplace Insert Carbon Monoxide Detector Requirements If Warranty Service is Needed Lifetime WarrantyFive Year Warranty Basic WarrantyMhsc Efficiency Ratings
Related manuals
Manual 40 pages 49.26 Kb

IDV380NVC, IDV490NVC, IDV380PVC, IDV490PVC specifications

The Monessen Hearth IDV490NVC, IDV380PVC, IDV380NVC, and IDV490PVC represent a cutting-edge series of direct vent gas fireplaces that combine efficiency, style, and innovative technology. These models are designed to enhance home aesthetics while providing efficient heating solutions.

One of the standout features of the Monessen Hearth models is their impressive heating capabilities. The IDV490NVC and IDV490PVC are designed for larger spaces, providing up to 37,000 BTUs, while the IDV380NVC and IDV380PVC are suitable for medium-sized areas, delivering up to 30,000 BTUs. This makes each fireplace an ideal choice for various residential applications, accommodating different room sizes and heating needs.

The appliances employ advanced direct vent technology, allowing for safe operation by drawing air from outside for combustion and venting exhaust gases outside. This feature ensures that indoor air quality remains unaffected, making these models eco-friendly alternatives to traditional fireplaces. The efficient combustion process also means lower gas consumption, resulting in cost savings and a reduced environmental footprint.

Each model comes equipped with a variety of flame and control options. The realistic ceramic logs and glowing embers create an inviting ambiance, while the adjustable flame height allows users to customize their experience. Additionally, an easy-to-use remote control feature gives users the convenience of adjusting flames and temperature settings without leaving their seats.

The construction of these fireplaces is robust, featuring high-quality materials that ensure durability and longevity. The heat-resistant glass allows for an unobstructed view of the flames, adding a touch of elegance to any room.

Aesthetic choices further enhance personalization, as Monessen offers customizable options for surrounds and mantels that blend seamlessly with various interior styles.

In summary, the Monessen Hearth IDV490NVC, IDV380PVC, IDV380NVC, and IDV490PVC fireplaces exemplify modern heating technology combined with stylish design. Their powerful heat output, direct vent capabilities, user-friendly controls, and customizable aesthetics make them exceptional choices for homeowners looking to elevate their living spaces while ensuring comfort and efficiency. Whether for aesthetic appeal or functional heating, these models provide a perfect balance for any modern home.