Monessen Hearth IDV490NVC manual Important Safety Information and code approval, Code Approval

Page 4

IDV380/IDV490 Fireplace Insert

IMPORTANT SAFETY INFORMATION and code approval

Continued from page 3

15.This appliance, when installed, must be electrically grounded in accordance with local codes or in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.1.

16.Do not obstruct the flow of combustion and ventilation air in any way. Provide adequate clearances around air openings into the combustion chamber along with adequate accessibility clearance for servicing and proper operation.

17.Do not use insert if any part has been exposed to or has been under water. Immediately call a qualified service technician to inspect the appliance and replace any part of the control system and any gas control which as been submerged in water.

18.Do not operate insert if any log is broken.

20.Do not operate the insert with glass door removed, cracked, or broken.

!WARNING

 

 

 

 

 

 

HOT GLASS WILL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CAUSE BURNS.

 

 

 

 

 

 

 

DO NOT TOUCH GLASS

 

 

 

 

 

 

 

UNTIL COOLED.

 

 

 

 

 

 

 

NEVER ALLOW CHILDREN

 

 

 

 

 

 

 

TO TOUCH GLASS.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

WARNING

Never connect unit to private (non-utility)

 

gas wells. This gas is commonly known

 

 

 

 

 

 

 

 

 

 

as wellhead gas.

 

 

 

 

 

 

 

 

 

IMPORTANT:

PLEASE READ THE FOLLOWING

CAREFULLY

It is normal for fireplaces fabricated of steel to give off some expansion and/or contraction noises during the start up or cool down cycle. Similar noises are found with your furnace heat exchanger or car engine.

IMPORTANT:

PLEASE READ THE FOLLOWING CAREFULLY

It is not unusual for gas fireplaces to give off some odor the first time it is burned. This is due to the manufacturing process.

Please ensure that your room is well ventilated during burn off — open all windows.

It is recommended that you burn your fireplace for at least ten (10) hours the first time you use it. Place the fan switch in the “OFF” position during this time.

Code Approval

Direct Vent type appliances draw all combustion air from outside of the dwelling through the vent pipe.

These appliances have been tested by CSA and found to comply with the established standards for DIRECT VENT GAS FIREPLACE HEATERS in the USA and Canada as follows:

LISTED VENTED GAS FIREPLACE HEATER

TESTED TO: ANSI Z21.88b-2008/CSA 2.33b-2008 STANDARDS

A manufactured home (USA only) or mobile home OEM installation must conform with the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, or when such a standard is not applicable, the Standard for Manufactured Home Installations, ANSI/NCSBCS A225.1, or Standard for Gas Equipped Recreational Vehicles and Mobile Housing, CSA Z240.4.

57D0016

Page 3 Page 5
Image 4
Page 3 Page 5
Contents IDV Series Direct Vent Gas Fireplace Insert IDV380/IDV490 Fireplace Insert Installer Important Safety InformationOwner Important Safety Information and code approval Code ApprovalProduct features Product SpecificationsHigh Elevations GAS pressuresInsert dimensions IDV380 IDV490Installation Planning Installation InformationBefore You Start Clearances Mantel Clearances Hearth RequirementsInstallation Insert PlacementInstallation ZERO-CLEARANCE Metal Fireplace RequirementsInstallation Precautions Venting RequirementsVenting installation Altitude ConsiderationsVent Configurations Manifold Removal and Installation Insert Installation Installing gas piping to fireplace locationInstallation items needed Check gas typeInsert installation Propane/LPDo not use open flame to Check GAS PressureCheck for gas leaks Electrical Wiring Remote Wall mounted SwitchLog placement Installing Logs and Rock Wool Ember Material in FireboxPin on burner. Figure Top Y Log #7 Install Surround Surround installationInstalling On/Off switch Installing Filigree panels and cabi- net door frame Door and Filigree installationInstalling Doors Initial lighting What to do if YOU Smell GASNever use an open flame to check for gas leak Approved leak testing method Operating InstructionsMain burner switch Adjusting blower speedLighting the burner Pilot positionAIR Shutter Adjustment Natural GAS only Adjust the AIR ShutterGlass Replacement Cleaning and Maintenance Cleaning glassVenting system Pilot and burner flamesFirebox cleaning Maintaining your heater’s appearanceMaintenance Yearly service procedureTroubleshooting Blower Removal and Assembly Blower Parts ListReplacement Parts Replacement Parts IDV380NVC IDV380PVC IDV490NVC IDV490PVCIDV380/IDV490 Fireplace Insert IDV380/IDV490 Fireplace Insert Carbon Monoxide Detector Requirements Lifetime Warranty Five Year WarrantyBasic Warranty If Warranty Service is NeededEfficiency Ratings Mhsc
Related manuals
Manual 40 pages 49.26 Kb

IDV380NVC, IDV490NVC, IDV380PVC, IDV490PVC specifications

The Monessen Hearth IDV490NVC, IDV380PVC, IDV380NVC, and IDV490PVC represent a cutting-edge series of direct vent gas fireplaces that combine efficiency, style, and innovative technology. These models are designed to enhance home aesthetics while providing efficient heating solutions.

One of the standout features of the Monessen Hearth models is their impressive heating capabilities. The IDV490NVC and IDV490PVC are designed for larger spaces, providing up to 37,000 BTUs, while the IDV380NVC and IDV380PVC are suitable for medium-sized areas, delivering up to 30,000 BTUs. This makes each fireplace an ideal choice for various residential applications, accommodating different room sizes and heating needs.

The appliances employ advanced direct vent technology, allowing for safe operation by drawing air from outside for combustion and venting exhaust gases outside. This feature ensures that indoor air quality remains unaffected, making these models eco-friendly alternatives to traditional fireplaces. The efficient combustion process also means lower gas consumption, resulting in cost savings and a reduced environmental footprint.

Each model comes equipped with a variety of flame and control options. The realistic ceramic logs and glowing embers create an inviting ambiance, while the adjustable flame height allows users to customize their experience. Additionally, an easy-to-use remote control feature gives users the convenience of adjusting flames and temperature settings without leaving their seats.

The construction of these fireplaces is robust, featuring high-quality materials that ensure durability and longevity. The heat-resistant glass allows for an unobstructed view of the flames, adding a touch of elegance to any room.

Aesthetic choices further enhance personalization, as Monessen offers customizable options for surrounds and mantels that blend seamlessly with various interior styles.

In summary, the Monessen Hearth IDV490NVC, IDV380PVC, IDV380NVC, and IDV490PVC fireplaces exemplify modern heating technology combined with stylish design. Their powerful heat output, direct vent capabilities, user-friendly controls, and customizable aesthetics make them exceptional choices for homeowners looking to elevate their living spaces while ensuring comfort and efficiency. Whether for aesthetic appeal or functional heating, these models provide a perfect balance for any modern home.
Top Page Image Contents