Monessen Hearth C2803VF, C2804VF Operation Of Thermostat Sensor, Electrical Wiring Milli-Volt

Page 15
OPERATION OF THERMOSTAT SENSOR

ELECTRICAL WIRING (MILLI-VOLT)

4.Remove adhesive backing from plastic clip. Press clip to bottom of valve. Clip thermo bulb into plastic clip. See Figure 10.

5.Reattach faceplate or reinstall base.

6.Install knob to shaft of t-stat sensor. See Figure 9, page 14.

OPERATION OF THERMOSTAT SENSOR

Valve

Thermo Figure 10 - Clipping Thermo Bulb intoPlastic Clip. Bulb

Plastic Clip

Figure 10 - Clipping Thermo Bulb into

Plastic Clip.

1.Follow millivolt lighting instructions on lighting plate attached to unit or in homeowner’s manual.

2.With control knob in the “ON” position make sure the ON/OFF switch is in the “OFF” position. See Figure 11.

3.The unit is now being controlled by the thermostat sensor. The sensor will now cycle the burners on and off. You can adjust how often the unit cycles by turning the control knob on the sensor.

ON/OFF

Switch

Control

Knob

��

 

�

 

�

�

�

 

�

 

�

 

�

 

�

 

�

 

�

 

�

 

�

�

 

�

 

��

 

��

 

�

�

�

 

�

 

�

 

�

 

�

 

�

 

�

 

�

 

�

 

�

T-Stat

Sensor

Figure 11 - Control Knob in “ON” Position and ON/OFF Switch in “OFF” Position

45D0080

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Do not try to light any appliance MODELS C2801VF, C2802VF C2803VF, and C2804VFNatural Gas or Propane/LPG Milli-VoltControl WHAT TO DO IF YOU SMELL GASCONTENTS IMPORTANT SAFETY INFORMATION INSTALLEROWNER Continued from page IMPORTANT SAFETY INFORMATIONInstruction Thermostat Plates Sensor Hi/Lo Knob PRODUCT FEATURESOn/Off Switch Data andOptional Optional Remote Receiver Off/Pilot/On KnobWHAT YOU WILL NEED FOR INSTALLATION GETTING STARTEDMAKE SURE YOU HAVE RECEIVED ALL PARTS IGNITION CONTROLS PRODUCT SPECIFICATIONSNATURAL GAS PROPANE / LPGCODES GENERAL INSTALLATION INFORMATIONDo not install the heater … •In high traffic areas •In windy or drafty areasBTU/Hr = L1 GENERAL INSTALLATION INFORMATIONFront View Corner InstallationWall Installation CLEARANCES / HEIGHT REQUIRMENTSFigure 4 - Gas Connection CONNECTING THE GASexplosion Connecting directly to an unregulatedCONNECTING REMOTE RECEIVER propane/L.P.G. tank can cause anMillivolt ELECTRICAL WIRING MILLI-VOLTFigure 7 - Wiring Diagram CONNECTING OPTIONAL WALL SWITCH OR THERMOSTATELECTRICAL WIRING MILLI-VOLT Figure 8 - Removing Face Plate from StoveScrews Plastic Clip OPERATION OF THERMOSTAT SENSORELECTRICAL WIRING MILLI-VOLT Figure 10 - Clipping Thermo Bulb intoa few hours to vent the odor LOG PLACEMENTDO NOT sprinkle volcanic rocks on the logs or around the pilot. This may cause sootingCHECKING PILOT FLAME FLAME APPEARANCECHECKING BURNER FLAME OPERATING INSTRUCTIONSFOR YOUR SAFETY READ BEFORE LIGHTING OPERATING INSTRUCTIONSWHAT TO DO IF YOU SMELL GAS MILLI-VOLTCONTROL LIGHTING INSTRUCTIONS TO TURN OFF GAS TO HEATEROPERATING INSTRUCTIONS OPERATING INSTRUCTIONS AND CLEANING AND SERVICING CLEANING AND SERVICINGMATCH LIGHTING INSTRUCTIONS REPLACEMENT PARTS LIST LOGSDescription REPLACEMENT PARTS BURNER ASSEMBLY45D0080 C2801/02/03/04VF REPLACEMENT PARTS LISTBURNER ASSEMBLY AccessoriesREMEDY TROUBLESHOOTINGOBSERVED PROBLEM POSSIBLE CAUSEREMEDY TROUBLESHOOTINGOBSERVED PROBLEM POSSIBLE CAUSE45D0080 45D0080 BASIC WARRANTY LIMITED LIFETIME WARRANTY POLICYLIFETIME WARRANTY FIVE YEAR WARRANTY
Top Page Image Contents