Monessen Hearth BDV500, BDV600, BDV300 Final Installation, Rock Wool Placement, LOG Placement

Page 33

FINAL INSTALLATION

ROCK WOOL PLACEMENT

1.Place rock wool on burner to provide glowing embers. For best results, pull the rock wool apart into pieces the size of a dime or smaller.

2.Distribute one layer of rock wool to cover the burner. See Figure 40.

3.Place the logs on the burner. See Log Placement below. Light unit and after 15 minutes, check burner flame and glow. See Burner Flame, page 38.

If the flame is blue and only in the center, turn off unit and let cool. After unit cools, remove logs. If the back holes are clear, add more rock wool to the center of the burner. Replace logs and check flame again. Save left over rock wool to refresh when cleaning later. Too much rock wool can disturb the flame and cause sooting on the glass or logs.

Burner

Cover with

Rock Wool

Figure 40 - Placement of Rock Wool on Burner

WARNING

Do not use the entire bag of rock wool

 

 

to cover the burner. This could cause

 

the flame to burn poorly and may lead

 

to sooting.

 

 

LOG PLACEMENT

1.Place rear log (#1) on grate assembly. Log should rest firmly on the two log mounting pins on the bars. See Figure 41.

2.Place top right log (#2) on the rear log. Rest the right back side of the log in the flat area of the rear log. Place the narrow front end of the log next to the center vertical grate bar. See Figure 41.

3.Place the top left log (#3) on the rear log. Nest the forked end of the top left log into the fork or the rear log. Rest the narrow end of the top left log behind the center vertical grate bar. See Figure 41.

LAVA ROCK AND EMBER PLACEMENT

Sprinkle lava rock on the floor of the inner combustion chamber. Evenly distribute the rock. Do not pile the lava rock up in front of grate. Do not place lava rock on the burner. If desired, purchase optional embers to decorate the floor of the fireplace.

(#1) Rear

Log

Log Mounting Pins

Left Vertical

Grate Bar

Center Vertical

Grate Bar

(#3) Top

(#2) Top

Left Log

Right Log

Flat

Area

WARNING

Do not sprinkle the lava rock or ember chunks on top of the burner. This may cause potential sooting, glass breakage and a fire hazard.

Right

Vertical

Grate Bar

Figure 41 - Log Placement

(BDV300, 400 shown)

54D0700

33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents What to do if YOU Smell GAS Installation and Operating InstructionsContents Important Safety Information InstallerOwner Non-utility gas wells. This Never connect unit to privateGas is commonly known as Wellhead gasProduct Specifications Product Features and Code ApprovalCode Approval Listed Vented GAS Fireplace HeaterInstalling Above 2000 Feet PRE-INSTALLATION InformationOrifice SIZES, Pressures and BTUs Before YOU StartFirebox Framing Fireplace FramingFireplace Dimensions 31/281/4 Locating Gas Fireplace Fireplace LocationClearances Clearances to CombustiblesMantel Clearances Securing Fireplace to Floor and Framing Studs Securing Fireplace to Floor or FramingVent Installation Installation InformationInstallation Precautions Finishing MaterialCombustible Clearances for Vent Pipe Vent InstallationAfter conversion to top vent Optional TOP Vent ApplicationConfiguration the 4 100mm flue pipe Should be concentric within the 65/8Installing a Vent System in AN Outside Chase Installation PlanningFor Horizontal Termination For Vertical TerminationMinimum Distances Horizontal Vent Termination LocationFeet HOW to USE the Vent GraphRear Through the Wall Applications Venting InstallationDo not recess vent termination Rear Wall Vent InstallationInto any wall. This will cause a fire hazardSee Figure Horizontal Termination ConfigurationsHorizontal Run Reduction Horizontal Termination ConfigurationBelow Grade Installation Below Grade InstallationsSupport Straps for Horizontal Runs Vertical THROUGH-THE-ROOF ApplicationsFlat Ceiling Installation Installation for Vertical TerminationCathedral Ceiling Installation Minimum HeightRoof Pitch Feet Meters Fireplace Installation Installing GAS Piping to Fireplace / Burner System LocationCheck GAS Type Gas Connection Electrical Wiring Checking GAS Pressure and Electrical InstallationDo not use open flame to check for Gas leaksRemote Wall Mounted Switch Electrical InstallationSwitch to heater Do not connect wallElectronic Pilot Ignition Wiring Remote Wall SwitchOptional DC Remote Systems Optional FAN/BLOWER Systems Blower Wiring DiagramGlass Frame Removal Glass RemovalKeep fingers clear. Remove control panel to operate middle Clamp on 500 and 600 unitsRock Wool Placement Final InstallationLOG Placement Lava Rock and Ember PlacementOperating Instructions MILLI-VOLT Leak TestingWhat to do if YOU Smell GAS Initial LightingApproved Leak Testing Method Main Burner Switch Lighting the BurnerPilot Position Operating Instructions Electronic Lighting Electronic IgnitionBURNER, Pilot and Control Compartment Cleaning and MaintenancePilot Flame BurnerGlass Door Vent SystemLogs Rock WoolTroubleshooting Symptom Possible Cause ActionStanding Pilot Ignition Troubleshooting Firebox Components Illustrated Parts ListsCC=Cottage Clay CR=Cottage Red Standing Pilot Millivolt Control Description Qty Electronic Ignition Ignition Module Vent Components Illustrated Parts ListDescription Qty BDV300 BDV400 BDV500 BDV600 Special Requirements Special Requirements Lifetime Warranty Five Year WarrantyBasic Warranty

BDV400, BDV500, BDV300, BDV600 specifications

The Monessen Hearth series, comprising the BDV600, BDV300, BDV500, and BDV400 models, stands out in the realm of gas fireplaces. These contemporary designs fuse aesthetic appeal with cutting-edge technology to provide users with a compelling heating solution. Each model offers distinct features while sharing a commitment to quality and performance.

Starting with the BDV600, this fireplace is known for its robust dual burner system that ensures vibrant flames and reliable heat output. Its impressive efficiency rating makes it ideal for energy-conscious consumers. Additionally, the BDV600 features a stunning realistic log set and allows for customization with various decorative media options, giving homeowners the ability to match their personal style.

Moving on to the BDV300, this model is compact yet powerful. It is designed for smaller spaces without sacrificing warmth or ambiance. The BDV300 utilizes advanced technology to enhance flame presence while minimizing energy consumption. The intuitive remote control system adds convenience, allowing users to adjust the flame height and heat settings effortlessly.

The BDV500, a mid-range option, offers an excellent balance of size and efficiency. This model incorporates a versatile installation design, permitting both direct venting and vent-free options. Homeowners appreciate the BDV500's variable speed blower, which helps distribute heat evenly throughout the room. Its sleek interface and easy-to-use controls make it an attractive choice for those looking to upgrade their home heating solutions.

Finally, the BDV400 combines aesthetic beauty with functional performance. This fireplace is equipped with a powerful yet quiet heating system. The BDV400's realistic flame presentation is driven by a unique burner design that creates a lifelike fire experience. Furthermore, its comprehensive safety features ensure peace of mind, including a safety screen and an automatic shut-off system.

All four models emphasize user-friendly design, featuring easy access for maintenance and cleaning. The advanced technologies built into these fireplaces help provide a cleaner burn, reducing pollutants and ensuring compliance with local regulations.

In summary, the Monessen Hearth BDV series—including the BDV600, BDV300, BDV500, and BDV400—offers homeowners a range of stylish and energy-efficient options. With unique features, advanced technologies, and dependable performance, these gas fireplaces take warmth and comfort to new heights, catering to diverse needs and preferences in modern living spaces.
Top Page Image Contents