Monessen Hearth BDV500, BDV600, BDV300, BDV400 Fireplace Location, Locating Gas Fireplace

Page 9

PRE-INSTALLATION INFORMATION

FIREPLACE LOCATION

Plan for the installation of your appliance. This includes determining where the unit is to be installed, the vent configuration to be used, framing and finishing details, and whether any optional accessories (i.e. blower, wall switch, or remote control) are desired. Consult your local building code agency to ensure compliance with local codes, including permits and inspec- tions.

The following factors should be taken into consideration:

•Clearance to side-wall, ceiling, woodwork, and windows. Minimum clearances to combustibles must be maintained.

•This fireplace may be installed along a wall, across a corner, or use an exterior chase. See Figure 4 for suggested loca- tions.

•Location should be out of high traffic areas and away from furniture and draperies due to heat from appliance.

•Never obstruct the front opening of the fireplace.

•Do not install in the vicinity where gasoline or other flammable liquids may be stored.

•Vent pipe routing. See Venting section found in this manual for allowable venting configurations.

•These units can be installed in a bedroom. See National Fuel Gas Code ANSI Z233.1/NFPA 54 — (current edition), the Uniform Mechanical Code — (current edition), and Local Building Codes for specific installation requirements.

A

Flat on Wall

B

Cross Corner

C

Island**

D

Room Divider*

E

Flat on Wall Corner*

F

Chase Installation

Y

4" Minimum

 

 

E

A

B

Y

 

 

 

 

 

X

 

 

C

D

 

 

Y

 

 

 

F

 

Figure 4 - Locating Gas Fireplace

**Island (C) and room divider (D) installation is possible as long as the horizontal portion of vent system (X) does not exceed 20'. See Installing Horizontal Termination Configuration on pages 18 and 19.

*When you install your fireplace in (D) room divider or (E) flat on wall corner positions (Y), a minimum of 6" clearance must be maintained from perpendicular wall and front of fireplace.

54D0700

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents What to do if YOU Smell GAS Installation and Operating InstructionsContents Important Safety Information InstallerOwner Non-utility gas wells. This Never connect unit to privateGas is commonly known as Wellhead gasProduct Specifications Product Features and Code ApprovalCode Approval Listed Vented GAS Fireplace HeaterInstalling Above 2000 Feet PRE-INSTALLATION InformationOrifice SIZES, Pressures and BTUs Before YOU StartFirebox Framing Fireplace FramingFireplace Dimensions 31/281/4 Locating Gas Fireplace Fireplace LocationClearances Clearances to CombustiblesMantel Clearances Securing Fireplace to Floor and Framing Studs Securing Fireplace to Floor or FramingVent Installation Installation InformationInstallation Precautions Finishing MaterialCombustible Clearances for Vent Pipe Vent InstallationAfter conversion to top vent Optional TOP Vent ApplicationConfiguration the 4 100mm flue pipe Should be concentric within the 65/8Installing a Vent System in AN Outside Chase Installation PlanningFor Horizontal Termination For Vertical TerminationMinimum Distances Horizontal Vent Termination LocationFeet HOW to USE the Vent GraphRear Through the Wall Applications Venting InstallationDo not recess vent termination Rear Wall Vent InstallationInto any wall. This will cause a fire hazardSee Figure Horizontal Termination ConfigurationsHorizontal Run Reduction Horizontal Termination ConfigurationBelow Grade Installation Below Grade InstallationsSupport Straps for Horizontal Runs Vertical THROUGH-THE-ROOF ApplicationsFlat Ceiling Installation Installation for Vertical TerminationCathedral Ceiling Installation Minimum HeightRoof Pitch Feet Meters Fireplace Installation Installing GAS Piping to Fireplace / Burner System LocationCheck GAS Type Gas Connection Electrical Wiring Checking GAS Pressure and Electrical InstallationDo not use open flame to check for Gas leaksRemote Wall Mounted Switch Electrical InstallationSwitch to heater Do not connect wallElectronic Pilot Ignition Wiring Remote Wall SwitchOptional DC Remote Systems Optional FAN/BLOWER Systems Blower Wiring DiagramGlass Frame Removal Glass RemovalKeep fingers clear. Remove control panel to operate middle Clamp on 500 and 600 unitsRock Wool Placement Final InstallationLOG Placement Lava Rock and Ember PlacementOperating Instructions MILLI-VOLT Leak TestingWhat to do if YOU Smell GAS Initial LightingApproved Leak Testing Method Main Burner Switch Lighting the BurnerPilot Position Operating Instructions Electronic Lighting Electronic IgnitionBURNER, Pilot and Control Compartment Cleaning and MaintenancePilot Flame BurnerGlass Door Vent SystemLogs Rock WoolTroubleshooting Symptom Possible Cause ActionStanding Pilot Ignition Troubleshooting Firebox Components Illustrated Parts ListsCC=Cottage Clay CR=Cottage Red Standing Pilot Millivolt Control Description Qty Electronic Ignition Ignition Module Vent Components Illustrated Parts ListDescription Qty BDV300 BDV400 BDV500 BDV600 Special Requirements Special Requirements Lifetime Warranty Five Year WarrantyBasic Warranty

BDV400, BDV500, BDV300, BDV600 specifications

The Monessen Hearth series, comprising the BDV600, BDV300, BDV500, and BDV400 models, stands out in the realm of gas fireplaces. These contemporary designs fuse aesthetic appeal with cutting-edge technology to provide users with a compelling heating solution. Each model offers distinct features while sharing a commitment to quality and performance.

Starting with the BDV600, this fireplace is known for its robust dual burner system that ensures vibrant flames and reliable heat output. Its impressive efficiency rating makes it ideal for energy-conscious consumers. Additionally, the BDV600 features a stunning realistic log set and allows for customization with various decorative media options, giving homeowners the ability to match their personal style.

Moving on to the BDV300, this model is compact yet powerful. It is designed for smaller spaces without sacrificing warmth or ambiance. The BDV300 utilizes advanced technology to enhance flame presence while minimizing energy consumption. The intuitive remote control system adds convenience, allowing users to adjust the flame height and heat settings effortlessly.

The BDV500, a mid-range option, offers an excellent balance of size and efficiency. This model incorporates a versatile installation design, permitting both direct venting and vent-free options. Homeowners appreciate the BDV500's variable speed blower, which helps distribute heat evenly throughout the room. Its sleek interface and easy-to-use controls make it an attractive choice for those looking to upgrade their home heating solutions.

Finally, the BDV400 combines aesthetic beauty with functional performance. This fireplace is equipped with a powerful yet quiet heating system. The BDV400's realistic flame presentation is driven by a unique burner design that creates a lifelike fire experience. Furthermore, its comprehensive safety features ensure peace of mind, including a safety screen and an automatic shut-off system.

All four models emphasize user-friendly design, featuring easy access for maintenance and cleaning. The advanced technologies built into these fireplaces help provide a cleaner burn, reducing pollutants and ensuring compliance with local regulations.

In summary, the Monessen Hearth BDV series—including the BDV600, BDV300, BDV500, and BDV400—offers homeowners a range of stylish and energy-efficient options. With unique features, advanced technologies, and dependable performance, these gas fireplaces take warmth and comfort to new heights, catering to diverse needs and preferences in modern living spaces.
Top Page Image Contents