Napoleon Fireplaces GD82NT, GD82PT manual Framing, Clearance to Combustibles

Page 15
FIGURE 30

FRAMING

It is best to frame your fireplace after it is positioned and the vent system is installed. Use 2x4’s and frame to local build- ing codes.

Note: In order to avoid the possibility of exposed insulation or vapour barrier coming in contact with the fireplace body, it is recommended that the walls of the fireplace enclosure

15

CLEARANCE TO COMBUSTIBLES

MAINTAIN THESE MINIMUM CLEARANCES TO COM- BUSTIBLES:

Fireplace framing - 0” to stand-offs (top, rear & sides) Fireplace finishing - 4” to sides of fireplace opening.

-21 3/4” to top of fireplace opening.

be “finished” (ie: drywall/sheetrock), as you would finish any other outside wall of a home. This will ensure that clearance to combustibles is maintained within the cavity.

It is not necessary to install a hearth extension, but the fire- place should be raised to be flush with either the hearth or the finished floor.

When roughing in the fireplace, raise the fireplace to accom- modate for the thickness of the finished floor materials, i.e. tile, carpeting, hard wood, which if not planned for will interfere with the removal of the hearth strip, which must be removed to access the firebox.

NON-COMBUSTIBLE FINISHING MATERIAL

 

 

 

Non-combustible

 

 

 

finishing material

 

 

 

(ie: cement board,

21

3

/4"

brick, stone, tile)

 

may be used to fin-

ish the front of the unit.

59 3/8"

Objects placed in front of the fireplace should be kept a mini- mum of 48” away from the front face.

For convenience, the stand-offs have been shipped flat. Before framing, ensure the stand-offs are opened and

4"

24"

4"

 

32"

 

screwed in place.

1"

 

 

 

MIN

 

 

 

44"

 

 

 

1"

29"

"

FIGURE 28

MIN

1/8

 

62

 

IMPORTANT:

The Park Ave. requires a minimum inside enclo- sure height of 72”.

For temperature require- ments, this area must be left unobstructed.

It is recommended that the enclosure be ventilat- ed at the top and bottom to circulate the hot air.

COMBUSTIBLE

MATERIAL

FIRESTOP

2"

 

SPACER

 

STUD

 

72"

 

2"

STAND OFF

SPACER

72"

58 1/2"

 

29"

22 1/2"

FIGURE 29

22 1/2"

2 FT.

29" 10" MIN MIN

FIGURE 31

NON-COMBUSTIBLE

WARNING

Facing and/or finishing

material must never

overhang into the fireplace

opening.

Do not distort or force the frame

kit components.

When using a rough finish materi- al (i.e.; stone), maintain a ¼” - ½” border from the framing components.

W415-0536 / C / 09.06.06

Page 14 Page 16
Image 15
Page 14 Page 16
Contents W415-0536 / C What to do if YOU Smell GAS Table of Contents Napoleon gas fireplace president’s lifetime limited warranty 21 3/4 to top of fireplace opening General instructionsGeneral inFORMATION 37 5/8 17 3/4 DIA 21 22 1/8 13 7VENTING Care of glass, and plated partsSupplier Formula 1 HT VT Formula 2 HT + VT 40 feet Example TOP Exit / horizontal terminationDefinitions Elbow Vent Length ValuesFormula 2 HT + VT 24.75 feet Formula HT 4.2 VT10.7 Formula HT + VT 24.75 feet 6.7Formula 1 HT 3VT Formula 2 HT + VT 40 feet Example TOP Exit Vertical terminationTOP Vertical termination Formula 1 HT VT Formula 2 HT + VT 40 feetW415-0536 / C Installation Wall and Ceiling Protection Vertical InstallationHorizontal Installation Through the attic Using Flexible Vent ComponentsHorizontal AIR Terminal Installation Vertical AIR Terminal InstallationUsing Rigid Vent Components Extended Horizontal AIR Terminal InstallationFireplace Vent Connection Use open flame Vertical Venting InstallationGAS Installation Restricting Vertical VentsClearance to Combustibles FramingElectrical Connection Hard Wiring ConnectionSchematic It is necessary to hard wire this fireplaceLog Shipping Bracket Log PlacementFinishing Door RemovalFirebox must be sealed Blower ReplacementNight Light Replacement Turn off the power to the fireplaceStep Decorative Brick Panel InstallationAfk / wi face kit installation REMOTE, Receiver and Valve Access Burner assembly removal1a. Rectangular Front Removal Hand Held Remote Operations Operation / MaintenanceTime OUT Fireplace OperationFAN Speed Setting Address Setting Procedure Dip switch number 0 = on / 1 = off Lighting Instructions For Your Safety Read BeforeOperating Instructions What to do if YOU Smell GASVenturi Adjustment AdjustmentsMaintenance Pilot Burner AdjustmentTerminal Kits ReplacementsReplacement Parts Accessories000 Symptom Problem Test Solution Trouble Shooting GuideShorten wire to correct length or wire gauge Pilot burning no Themostat or switch is deCheck that the wire is connected to the push button ignitor Replace the wire if the wire insulation is broken or frayedFireplace Service History W415-0536 / C W415-0536 / C

GD82PT, GD82NT specifications

Napoleon Fireplaces has long been recognized for its exceptional quality and innovative designs in the world of home heating. Among its impressive lineup are the GD82PT and GD82NT gas fireplaces, two models that stand out for their remarkable features and technologies. These fireplaces provide an ideal combination of aesthetic appeal and functional performance, making them a popular choice for modern homes.

Both the GD82PT and GD82NT are direct vent gas fireplaces, meaning they efficiently draw air from the outside for combustion and exhaust the leftover gases outside, ensuring optimal indoor air quality. This system allows them to be installed in a variety of locations without the need for a traditional chimney, providing flexibility in design and placement.

One of the key features of these models is their large viewing area, which is enhanced by a minimalist design that eliminates bulky frames. This offers an unobstructed view of the mesmerizing flames, turning the fireplace into a stunning focal point in any room. Additionally, both models boast an impressive heating capacity, ensuring that they efficiently warm up spaces even in the coldest climates.

The GD82PT model comes with a traditional logset and ember bed, creating a classic look that many homeowners desire. It is designed to accommodate a 35,000 BTU input, providing substantial heat while still being energy efficient. The GD82NT, on the other hand, features a contemporary linear design, which appeals to those looking for a modern aesthetic in their living spaces. This model also includes a unique glass media option that allows for a sleek and stylish appearance.

Both fireplaces feature Napoleon's advanced electronic ignition system, which ensures a reliable startup every time. Furthermore, the built-in remote control allows users to adjust heat output and flame height with ease. These models are also equipped with a variable speed blower, enhancing heat circulation throughout the room, making them not only visually appealing but highly functional as well.

Safety is another priority for Napoleon. Both models come with a safety screen barrier, preventing accidental contact with the hot glass surface. The intelligent gas control system also includes an oxygen depletion sensor, automatically shutting off the gas supply if oxygen levels drop to unsafe levels.

In summary, the Napoleon GD82PT and GD82NT gas fireplaces exemplify cutting-edge technology and elegant design, providing warmth and ambience to any space. With their innovative features, customizable options, and a strong commitment to safety, these models represent the pinnacle of modern fireplace design.
Top Page Image Contents