Trane TSC060-120 Electric Heaters, Roof Curb, Remote Potentiometer, Manual Outside Air Damper

Page 46

Mechanical Specifications

Accessories/Options

Electric Heaters

Field-installed electric heat modules shall be available for installation within basic unit. Electric heater elements shall be constructed of heavy-duty nickel chromium elements internally delta connected for 200 volt, wye connected for 380-415 volt. Staging shall be achieved through the unitary control processor (UCP). Each heater package shall have automatically reset high limit control operating through heating element contactors. All heaters shall be individually fused from the factory, where required. Power assemblies shall provide single-point connection.

Roof Curb

The roof curb shall be designed to mate with the unit’s downflow supply and return and provide support and a water tight installation when installed properly. The roof curb design shall allow field- fabricated rectangular supply/return ductwork to be connected directly to the curb. Curb shall be shipped knocked down for field assembly and shall include wood nailer strips.

Economizer

This accessory shall be either field or factory-installed and shall be available with or without barometric relief.The assembly includes fully modulating 0-100 percent motor and dampers, minimum position setting, preset linkage, wiring harness with plug, spring return actuator and fixed dry bulb control.The barometric relief shall provide a pressure operated damper that shall be gravity closing and shall prohibit entrance of outside air during the equipment “off” cycle. Optional solid state or differential enthalpy control shall be available for either factory or field installation.The factory-installed economizer arrives in the shipping position and shall be moved to the operating position by the installing contractor.

Phase Monitor

Phase monitor shall provide 100% protection for motors and compressors against problems caused by phase loss, phase imbalance, and phase reversal. Phase monitor is equipped with an LED that provides an ON or FAULT indicator.

Remote Potentiometer

The minimum position setting of the economizer shall be adjusted with this accessory.

Manual Outside Air Damper

Factory or field-installed rain hood and screen shall provide up to 50 percent outside air.

Motorized Outside Air Dampers Factory or field-installed manually set outdoor air dampers shall provide up to 50 percent outside air. Once set, outdoor air dampers shall open to set position when indoor fan starts.The damper shall close to the full closed position when indoor fan shuts down.

Discharge Air Sensing

This factory of field-installed option provides true discharge air sensing in heating models.This sensor is a status indicator readable throughTracer™ or Tracker™.

Oversized Motors

Factory or field-installed oversized motors shall be available for high static applications.

Clogged Filter/Fan Failure Switch

A dedicated differential pressure switch is available, factory-installed, to achieve active fan failure indication and/or clogged filter indication.These indications will be registered with either a zone sensor with status indication lights or an Integrated Comfort™ System.

High Pressure Cutout

Standard on all units.

Hinged Access Doors

Sheet metal hinges are available factory- installed on the Filter/Evaporator, Supply Fan/Heat, and the Compressor/Control Access Doors.

Black Epoxy Coated Condenser Coil

The coil provides corrosion protection to condenser coils for seacoast application. The protection is a factory-applied thermoset vinyl coating, bonded to normal aluminum fin stock.The uniform thickness of the bonded vinyl layer exhibits excellent corrosion protection.

46

RT-PRC016-EN

Page 45 Page 47
Image 46
Page 45 Page 47
Contents Packaged Cooling with Electric Heat Rooftop Units Introduction American Standard Inc. All rights reservedContents Features and Benefits Standardized Components Easy Access Low Voltage Terminal BoardFlexible Applications Micro Controls ReliaTel MicroEconomizer Hinged Access DoorsPhase Monitor Comm-3/4Trane Communication InterfaceWe test designs at our factory not on our customers Quality And Reliability TestingVariTrac Clearance Requirements Barometric ReliefCondensate Trap Unit PitchHeating Capacity Step Accessory SelectionCooling Capacity Step Air Delivery SelectionSelection Procedure IP Units Model Number Description 060 11 12,13General Data Table GD 1 General DataTable PD-1 Gross Cooling Capacities kW -TSC060AD SI Performance DataTable PD-1a Gross Cooling Capacities MBH TSC060AD IP Table PD-2 Gross Cooling Capacities kW -TSC072AD SI Table PD-2a Gross Cooling Capacities MBH -TSC072AD IPTable PD-3 Gross Cooling Capacities kW -TSC090AD SI Table PD-3a Gross Cooling Capacities MBH -TSC090AD IPTable PD-4 Gross Cooling Capacities kW -TSC102AD SI Table PD-4a Gross Cooling Capacities MBH -TSC102AD IPTable PD-5 Gross Cooling Capacities kW -TSC120AD SI Table PD-5a Gross Cooling Capacities MBH -TSC120AD IP2 HP Standard Motor & Drive ← 1.12 Nom kW Standard MotorHi Static Drive ← 1-1/2 HP Standard Motor← 1.12 Nom kW Standard Motor & Hi Static Drive Nom kW Standard Motor & Drive2 HP Standard Motor 2 HP Standard Motor Hi Static Drive Nom kW Std MotorNom kW Over-Sized Motor Hi Static Drive 2 HP Standard Mtr Drive2 HP Standard Motor & Low Static Drive Nom kW Standard Motor & Hi Static DriveNom kW Over-Sized Motor & Hi Static Drive 2 HP Std Motor & Hi Static DriveHP Standard Mtr HP Standard Motor Drive Hi Static Drive HP Std Motor & Low Static Drive Nom kW Standard Motor & Drive Nom kW OSMotor & Hi Static Drive HP Std Motor & Hi Static Drive HP Over-Sized MotorHP Standard Motor & Low Static Drive Nom kW Over-Sized Motor & High Static DriveHP Standard Mtr & Drive HP Std Motor & Hi Static Drive HP Std Mtr & Low Static Drive Nom kW Std Mtr Nom kW Over-Sized High Static DriveNom kW Standard Motor & High Static Drive HP Over-Sized Mtr & DriveNom kW Standard Motor & Low Static Drive 275 300 325 350 375 400 425 450 475 500 HP Standard Motor & High Static DriveTable PD-16 Standard Motor & Sheave/Fan Speed RPM Table PD-20 Sound Power Level dB ref -12WattsTable PD-19 Oversized Motor & Drive Sheave/Fan Speed RPM 100% OA 100% RA Model No M3/h EconomizerUnit Airflow Standard Pleated Filters OA/RA Dampers2 Downflow Horizontal 13-27Table PD-23 Auxiliary Electric Heat Capacity SI Table PD-23A Auxiliary Electric Heat Capacity IP11.3 13.5 07.5 09.010.9 13.0 14.4 17.2Zone Sensors Zone ControlsAutomatic Changeover One Heat Table ED-1 Unit Wiring Electrical DataZone Sensors Typical Number Of Wires Jobsite ConnectionsDimensional TSC060DataTSC060 DataTSC060 TSC072-090 TSC102-120 DataTSC072-120 ALL Flanges 1 1/4 31 MM TSC060 Economizer , Manual or Motorized Fresh Air Damper Dimensional TSC060TSC060 Swing Diameter for Hinged Doors Option Dimensional TSC072-120 Table W-2 Accessory Net Weights1 2 kg WeightsTable W-2a Accessory Net Weights1 2 lbs Mechanical Specifications Roof Curb Clogged Filter/Fan Failure SwitchElectric Heaters Remote PotentiometerZone Sensor Differential Pressure SwitchesComm-5 LonTalk Communication Interface ThermostatsSupersedes PL-UN-000-RT-PRC016-EN-12-03 Literature Order NumberFile Number PL-UN-000-RT-PRC016-EN-02-04 Stocking Location 03-03Webb/Mason 02-04 Electronic Only

TSC060-120 specifications

The Trane TSC060-120 is a prominent member of Trane's commercial HVAC (Heating, Ventilation, and Air Conditioning) systems, designed to meet the demands of various applications, from small offices to larger commercial venues. This model is part of Trane’s variable refrigerant flow (VRF) systems, which are known for their energy efficiency and flexibility.

One of the standout features of the TSC060-120 is its capacity range, which allows for cooling and heating capacities between 60,000 to 120,000 BTUs. This makes it suitable for diverse environments, adapting well to fluctuating load requirements. Additionally, the unit is designed with a modular approach, meaning that multiple units can be connected to meet larger capacity needs without sacrificing efficiency.

The Trane TSC060-120 incorporates advanced inverter technology, which helps optimize energy consumption by adjusting the compressor speed based on the real-time thermal load of the building. This results in a significant reduction in energy costs and improved comfort levels for occupants. The unit also features a high-efficiency multi-stage filtration system that not only ensures clean air circulation but also contributes to the overall indoor air quality.

The system utilizes a compact and versatile design, allowing for flexible installation options. Its lightweight structure and smaller footprint make it easier to install in tight spaces while still accommodating a powerful performance. The TSC060-120 is designed for quiet operation, which is crucial for noise-sensitive environments, delivering comfort without disruptive sound levels.

In terms of control and monitoring, the TSC060-120 is compatible with Trane's advanced building management systems. This integration allows facility managers to monitor energy usage, schedule maintenance, and control temperatures remotely, enhancing overall operational efficiency.

Moreover, the unit is built with sustainability in mind, using eco-friendly refrigerants that comply with the latest environmental regulations. This commitment to sustainability not only minimizes the ecological footprint but also positions the Trane TSC060-120 as a forward-thinking choice for businesses looking to enhance their energy strategy.

In summary, the Trane TSC060-120 stands out for its efficiency, flexibility, and advanced technology, making it a solid choice for commercial HVAC applications. With its combination of high performance, advanced control features, and commitment to sustainability, it provides an effective solution for modern climate control needs.
Top Page Image Contents