Vermont Casting 2478 manual Maintenance, Cleaning the Glass, Adjust the Door Latch

Page 23

Dutchwest Non-Catalytic Convection Heater

Maintenance

Keep Your Stove Looking New

And Working Its Best

Care of the Cast Iron Surface

An occasional dusting with a dry rag will keep the painted cast iron of your Dutchwest Convection Heater looking new.

If the paint needs retouching, allow the stove to cool completely. Wire-brush areas needing to be painted. Remove non-painted components such as air controls or cover them with masking tape. Touch up the stove with high temperature stove paint available from your local dealer. Apply the paint sparingly. Two light coats are better than one heavy one.

Cleaning the Glass

You will find that most of the carbon deposits on the glass will burn off regularly during hot fires. You can wipe fly ash from the glass when hot using a crumpled piece of dry newspaper. Never use liquid cleaning agents on hot glass. If you wish to clean the glass more thoroughly, follow this procedure:

•Be sure the glass is completely cool.

•Use a glass cleaner especially made for this pur- pose.

•Dry the glass completely.

Adjust the Door Latch

The door latches must close tightly to ensure a good seal between the each door and the stove plates. With time and use, the door latches will require periodic adjustment. Follow this procedure: (Fig. 30)

1.Loosen the small locking nut with an open end wrench.

2.Use the allen wrench (included with the stove) to turn the striker screw clockwise one quarter-turn and close the door to test the engagement. The door latch should engage tightly when closed. Make further adjustments in small increments.

3.When the striker screw is properly adjusted, tighten the small locking nut against the pawl without allow- ing the striker screw to turn.

Small Locking

Large Locking Nut

Nut

Pawl

 

Striker

 

Screw

 

Door

ST806

Fig. 30 Door latch adjustment.

Test and Repair the Door Gaskets

Air leaks can be caused by low spots in the door gas- kets. To locate such low spots, close each door on a slip of paper and attempt to pull the paper free. If the paper slips out without tearing, the gasket isn’t snug enough at that spot.

If the seal cannot be improved by adjusting the door latch, try shimming the gasket. Pack a small quantity of cement or a smaller diameter gasket into the channel beneath the gasket to lift the main gasket and thereby improve its contact with the door frame.

If shimming does not improve the seal, replace the gasket following these steps:

1.Remove the original gasket by grasping an end and pulling firmly.

2.Wearing safety goggles, use a wire brush or the tip of a screwdriver to clean the channel of any remain- ing cement or bits of gasket.

Remove the old gasket by pulling gently, but firmly.

ST440

Fig. 31 Door gasket.

30002278

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Non-Catalytic Convection Heater Model Table of Contents Accessories Model SpecificationsMasonry Chimneys InstallationChimney Types Prefabricated Chimneys Guidelines for Installing the Chimney ConnectorTwo Types of Connector Single-Wall ConnectorSecuring the Connector to a Prefabricated Chimney Double-Wall ConnectorAssembling Single-Wall Chimney Connector Fireplace Installations Above the Fireplace Securing the Connector to a Masonry ChimneyFreestanding Installations Wall Pass-Throughs Fireplace Installations Through the FireplaceCanada Floor ProtectionProcedure Fireplace InstallationsSafe Ways to Reduce Clearances Fireplace Installation ClearancesClearances Keep the Stove a Safe Distance From Surrounding MaterialsClearance Chart Reference Diagrams Designing a Safe InstallationOnly Corner Parallel Installations Stove Clearance Side Rear3Chimney Connector Clearance Right SideDutchwest Convection Heater Model Corner Parallel Installations Chimney Connector Side RearDutchWest Non-Catalytic Convection Heater Model #2478 Wall Heat Shield DimensionsAttach the Legs and Heat Shield AssemblyUnpack the Parts Fan Kit Installation Operation Heater Controls and Features Air ControlLoad Doors Damper Function Successful Wood BurningBurn Only High-Quality Fuel Break-in Fires Use the Air Control Settings That Work Best for YouHow to Build and Maintain a Wood Fire Loading Wood Reloading and Reviving the Fire Lighting the FireSafe Ash Handling Remove Ashes FrequentlyTest and Repair the Door Gaskets MaintenanceCleaning the Glass Adjust the Door LatchAvoid Damaging the Glass Door Panel Damper AdjustmentPrimary Air Control Adjustment Maintenance Schedule Stove Cleaning the Chimney SystemInspect Regularly, Clean As Required TWO Weeks Draft Management Creosote Draft TestingSingle Venting FuelConclusion Dutchwest Convection Heater Dutchwest Convection Heater Months, whichever is longer Limited Lifetime Warranty

2478 specifications

Vermont Castings 2478 is a premium wood-burning stove that embodies quality craftsmanship and efficiency, making it a top choice for homeowners who prioritize both style and functionality. Renowned for its durability and timeless design, the 2478 model is part of the Vermont Castings line, a brand synonymous with excellence in the world of heating appliances.

One of the standout features of the 2478 is its impressive heating capacity. It can efficiently heat spaces of up to 2,100 square feet, making it suitable for large living areas or even small homes. This capability is complemented by its easy-to-use, user-friendly interface, which allows for intuitive operation and precise temperature control.

The 2478 employs advanced Catalytic Combustion technology, which optimizes fuel efficiency while significantly reducing emissions. This technology ensures that the stove burns wood cleanly and effectively, maximizing heat output and minimizing the environmental impact. The catalytic converter enhances the combustion process, providing a longer burn time and requiring less frequent refueling.

In terms of construction, the Vermont Castings 2478 features a robust cast iron body that not only contributes to its aesthetic appeal but also provides exceptional heat retention. The stove is built to last, designed to withstand high temperatures while delivering consistent warmth. The cast iron grates and firebox contribute to excellent heat distribution, creating a cozy atmosphere throughout the room.

Another notable characteristic is the large glass door that offers a beautiful view of the flames, adding a visual focal point to any space. The air wash system keeps the glass clean, allowing for an unobstructed view of the fire. A variety of finishes are available, allowing homeowners to choose a style that best fits their décor, from classic black to rich enamel colors.

The Vermont Castings 2478 is also designed with safety in mind. It includes features such as an adjustable air control system for improved combustion management and a built-in heat shield that protects surrounding areas from excessive heat.

In summary, the Vermont Castings 2478 is a highly efficient, stylish wood-burning stove that provides warmth and comfort in a reliable and environmentally responsible manner. With its combination of advanced technology, durable construction, and elegant design, the 2478 is a worthy investment for any home. Whether you're seeking to enhance your living space or reduce heating costs, this stove stands out as a classic choice in the realm of heating solutions.
Top Page Image Contents