Vermont Casting 2997, 2950, 2951, 2998, 2996, 2995 manual Location of Vent Termination

Page 9

Vermont Castings Pinnacle & Stardance Direct Vent - Rear Vent Gas Heaters

Vent Termination Clearances

Your stove is approved to be vented either through the side wall, or vertical through the roof.

•Vermont Castings, Majestic Products does not require any opening for inspection of vent pipe.

•Only Vermont Castings, Majestic Products vent- ing components specifically approved and labelled for this stove may be used.

•Minimum clearances between vent pipes and combustible materials is one (1") inch (25 mm), except where stated otherwise.

•Venting terminals shall not be recessed into a wall or siding.

•Horizontal venting must be installed on a level plane without an inclining or declining slope.

There must not be any obstruction such as bushes, garden sheds, fences, decks or utility buildings within 24" from the front of the termination hood.

Do not locate termination hood where excessive snow or ice build up may occur. Be sure to check vent termination area after snow falls, and clear to prevent accidental blockage of venting system. When using snow blowers, make sure snow is not directed towards vent termination area.

Location of Vent Termination

It is imperative the vent termination be located observ- ing the minimum clearances as shown in Figure 9.

20003457

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Pinnacle & Stardance Direct Vent, Rear Vent Gas Heater Table of Contents Installation & Operating Instructions Stove Dimensions Stardance Direct Vent Gas Heater Stove Dimensions Pinnacle Direct Vent Gas HeaterMinimum Clearances to Combustible Materials Clearance RequirementsMantel Clearances Hearth Requirements Gas SpecificationsGas Inlet and Manifold Pressures Input Model Fuel Gas Control BTU/hHorizontal Termination High ElevationsVent Termination Clearances Vertical TerminationLocation of Vent Termination General Venting Information Termination Location Canadian Installations US InstallationsTermination Clearances Vent Components Parts Bag Contents Assembly ProceduresTool/Materials Required Firebox PreparationFasten the left side to the rear shroud Heater Shell AssemblyInstall the Firebox Install Optional Fan Kit #2960/FK28Fan Kit Contents Rear Vent Venting System Assembly Direct Vent General InformationVent Opening -Noncombustible Wall Through Side Wall Vent Termination Below GradeInstall inner starter pipe and inner elbow Vent Opening Noncombustible Wall Side Wall Termination Assembly400mm below the base of the snorkel. Install a ³⁄₈ x 9³⁄₈ 240mm x 240mm Vertical Through the Roof Vent AssemblyFireplace Vent Termination Clearances Vertical Through Existing ChimneyFireplace Installation Requirements PDV20 Fireplace Installation Requirements Sdvr Install ON/OFF Switch R Models only Complete the AssemblyConnect the Gas Supply Line Burner InformationThis completes assembly of the PDV20 and Sdvr stove Install the Front and Top PlatesThermostat Connection Use only a thermostat rated for 500 750 millivoltsLogs Install the Log SetModels 2995, 2996, 2997 Models 2950Flame Characteristics Flame & Temperature AdjustmentOperation Your First FireCorrect pilot flame pattern. PSE Pilot Lighting And Operating Instructions To Turn Off Gas To HeaterWhat to do if YOU Smell GAS Symptom Possible Causes Corrective Action Troubleshooting / Honeywell #8420 Gas Control SystemTransmitter Operation Off Mode Shut Off ProcedureOn Manual Mode Delay Timer ModeFan Override During Auto Mode Auto ModeChange Between F/C Temperature Units Disable Thermostat FunctionLocal Path Conversion Procedure Conversion PrecautionsAuto Path Fuel Conversion InstructionsPilot Type Models 2995, 2996 R Models OnlyAll Models Models 2997, 2998 RF Models OnlyConversion to Natural Gas Input BTU/h Conversion to LP Input BTU/hMaintenance Gasket Replacement Inspect the Vent System AnnuallyCheck the Gas Flame Regularly Wiring Diagrams Stove Disassembly5a,b6 PDV20 Sdvr Description 2950Shell Enamel Part Numbers PDV20 Color Fuel Conversion KitsLeft End Right End Front Control Door Shell Enamel Part Numbers Sdvr ColorRemote Controls Optional AccessoriesFan Kits Screen KitIf Warranty Service is NEEDED… Product Covered by this WarrantyVermont Castings, Majestic Products

2950, 2995, 2998, 2996, 2997 specifications

Vermont Castings is renowned for its high-quality cast iron stoves and fireplaces, and the models 2996, 2951, 2950, 2998, and 2997 exemplify this legacy. These stoves are designed to provide both efficiency and aesthetic appeal, making them ideal choices for any home.

Starting with the Vermont Casting 2996, this model is a highly efficient wood-burning stove known for its impressive heat output. It features a robust cast iron construction that not only enhances durability but also retains heat effectively, ensuring a long-lasting warmth. The 2996 boasts an advanced air wash system, keeping the glass door clean for a clear view of the flames while promoting optimal burn efficiency.

The Vermont Casting 2951 is another standout model, recognized for its compact size without sacrificing performance. This stove is designed for smaller spaces and is equipped with an innovative catalytic combustor that maximizes fuel efficiency and minimizes emissions. Its elegant design includes a variety of color options, allowing homeowners to select a finish that complements their interiors perfectly.

Moving on to the Vermont Casting 2950, this model offers a blend of tradition and modern technology. It utilizes a secondary combustion system that captures and re-burns gases released during the burning process. This leads to cleaner combustion and increased energy output. The 2950's detailed cast iron craftsmanship not only provides classic appeal but also ensures longevity.

The 2998 model stands out with its large firebox capacity, making it suitable for extended burn times. Designed for wood logs up to 20 inches, it offers an efficient heat output, making it ideal for colder climates. The stove features an easy-to-use air control that allows users to adjust the burn rate for their heating needs, promoting both efficiency and comfort.

Lastly, the Vermont Casting 2997 brings a unique blend of style and functionality. Its distinctive design includes an optional soapstone top, enhancing heat retention and providing an elegant aesthetic. With built-in features like the easy-access ash pan, homeowners can enjoy a hassle-free experience while maintaining their stove.

Overall, these Vermont Castings models showcase advanced heating technologies combined with beautiful design. Their commitment to efficiency, durability, and aesthetics makes them a popular choice for those seeking a reliable heating solution. Whether it's for the cozy ambiance or efficient warmth, Vermont Castings continues to set a standard in the wood stove industry.
Top Page Image Contents