What Kind of Chimney to Use, Chimney Size

What Kind of Chimney to Use

You must connect the Encore to a code-approved masonry chimney with a ﬂue liner, to a relined masonry chimney that meets local codes, or to a prefabricated metal chimney that complies with the requirements for Type HT chimneys in the Standard for Chimneys, Factory-Built, Residential Type and Building Heating Appliance, UL 103. (Fig. 3) The chimney and chimney connector must be in good condition and kept clean.

A prefabricated double- wall insulated chimney

A tile-lined masonry chimney

ST241

Fig. 3 Approved chimney types.

If you use an existing masonry chimney, it must be inspected to ensure it is in a safe condition before the stove is installed. Your local professional chimney sweep, building inspector, or ﬁre department ofﬁcial will be able to inspect the chimney or provide a referral to someone who can.

The chimney should extend at least 3’ (914 mm) above the highest point where it passes through a roof, and at least 2’ (610 mm) higher than any portion of a building within 10’ (3 m). (Fig. 4)

For proper draft and good performance, any chimney used with an Encore should extend at least 16’ (5 m) above the ﬂue collar of the stove.

0 To 10'
2' Min. 3'	0 To 10'
Min.
	2' Min. 3'
	Min.
Reference
Point	AC617

Fig. 4 The 2’-3’-10’ Chimney Rule.

Encore Woodburning Stove

Masonry Chimneys

An inspection of the chimney must conﬁrm that it has a lining. Do not use an unlined chimney. The chimney should have no cracks, loose mortar, other signs of deterioration, and blockage. Repair any defects before the chimney is used with your stove.

Unused openings in an existing masonry chimney must be sealed with masonry to the thickness of the chimney wall, and the chimney liner should be repaired. Open- ings sealed with pie plates or wallpaper are a hazard and should be sealed with mortar or refractory cement. In the event of a chimney ﬁre, ﬂames and smoke may be forced out of these unused thimbles.

The chimney should be thoroughly cleaned before use.

A newly-built masonry chimney must conform to the standards of your local building code or, in the absence of a local code, to a recognized national code. Masonry chimneys must be lined, either with code-approved masonry or pre-cast refractory tiles, stainless steel pipe, or a code-approved, “poured-in-place” liner. The chimney’s clean-out door must seal tightly.

Prefabricated Chimneys

A prefabricated metal chimney must be one tested and listed for use with solid-fuel burning appliances to the High-Temperature (H.T.) Chimney Standard UL-103- 1985 (2100°F) for the United States, and High Temper- ature (650°C) Standard ULC S-629 for Canada.

DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.

Chimney Size

An Encore with an 8” (203 mm) ﬂue collar is approved for venting into a masonry chimney with a nominal ﬂue size of 8” x 8” (203 x 203 mm) or 8” x 12” (203 x

305 mm), and into a round ﬂue with nominal ﬂue size of 8” (203 mm). An Encore with a 6” (152 mm) ﬂue collar is approved for venting into a masonry chimney with a nominal ﬂue size of 8” x 8” (203 x 203 mm), and into a round ﬂue with nominal ﬂue of 6” (152 mm).

NOTE: When installed with a 6” ﬂue collar, the Encore may not be operated with the front doors open.

Whatever the ﬂue collar size, an Encore may be vented into larger chimneys as well. However, chimneys with liners larger than 8” x 12” (203 x 305mm) may experi- ence rapid cooling of smoke and reduction in draft, es- pecially if the chimneys are located outside the home. These large chimneys may need to be insulated or have their ﬂues relined for proper stove performance.

Accessories to help make the connection between stainless steel chimney liners and your Encore are available through your local dealer.

2000956