Vermont Casting 0968, 1910 installation instructions Through the Fireplace, Wall pass-Throughs

Page 9

If the chimney connector in your installation enters the chimney above a fireplace, follow all the guidelines mentioned above for freestanding installations. In addition, give special consideration to the following points:

Check the clearance between the stove and the chimney connector, and any combustible trim or the mantel.

Check the clearance between the chimney connector and the ceiling. The clearance should be at least 18" (457 mm).

The fireplace damper must be sealed to keep room air from escaping up the flue. However, it must be possible to reopen the damper to inspect or clean the chimney.

Through the Fireplace

Installations through the fireplace opening have not been tested or approved.

Wall pass-Throughs

Whenever possible, design your installation so that the connector does not pass through a combustible wall. If you are considering a wall pass-through in your installation, check with your building inspector before you begin. Also, check with the chimney connector manufacturer for any specific requirements.

Accessories are available for use as wall pass- throughs. If using one of these, make sure it has been tested and listed for use as a wall pass-through.

In the United States, the National Fire Protection Association (NFPA) has established guidelines for passing chimney connectors through combustible walls. Many building code inspectors follow these guidelines when approving installations.

Figure 8 shows one NFPA-recommended method. All combustible material in the wall is cut away from the single-wall connector to provide the required 12" (300

mm)clearance. Any material used to close up the opening must be noncombustible.

Three other methods are also approved by the NFPA:

• Placing a section of chimney connector inside a ventilated thimble, which in turn is separated from combustibles by 6" (150 mm) of fiberglass insulat- ing material.

• Placing a section of chimney connector inside a section of 9" (230 mm) diameter, solid-insulated, factory-built chimney, with two inches of air space between the chimney section and combustibles.

• Using a section of solid-insulated double-wall High Temperature chimney, with an inside diameter the same as the chimney connector, at least one inch of solid insulation, and a minimum of 9 inches (229mm) air space between the outer wall of the chimney section and combustibles.

Vermont Castings Defiant

 

Wall Stud

 

Chimney

 

Connector

 

T

 

DE

 

FIAN

 

12” of

 

Noncombustible

 

Material

Floor

 

Protection

 

ST493

Fig. 8

an approved wall pass-through for the United States.

In Canada, The Canadian Standards Association has established different guidelines for wall pass- throughs. Figure 9 shows one method, in which all combustible material in the wall is cut away to provide the required 18" (460 mm) clearance for the connector. The resulting space must remain empty. A flush- mounted sheet metal cover may be used on one side only. If covers must be used on both sides, each cover must be mounted on noncombustible spacers at least 1" (25 mm) clear of the wall.

Your local dealer or your local building inspector can provide details for other approved methods of passing a chimney connector through a combustible wall in your area. In Canada, this type of installation must conform to CAN/CSA-B365, Installation Code for Solid Fuel Burning Appliances and Equipment.

18” (460mm) clearance

between pipe and

sides/top/bottom of

opening

T

DE

FIAN

ST494

Fig. 9 An approved wall pass-through for Canada.

9

Image 9
Contents Defiant Save These Instructions for Future Reference WelcomeStory of the Defiant Table of ContentsDefiant, Model SpecificationsInstallation Outside AirChimney Height Masonry Chimneys What Kind of Chimney to UsePrefabricated Chimneys Chimney SizeSingle-wall Chimney Connectors Chimney Connector GuidelinesFreestanding Installations Securing the Single-wall Connector to a Masonry ChimneyFireplace Installations Above the FireplaceWall pass-Throughs Through the FireplaceFloor Protection Floor Protection for Fireplace InstallationKeep the Stove a Safe Distance from Surrounding Materials Safe Ways to Reduce ClearancesWall Shields Stove Clearance Unprotected Surfaces Protected Surfaces Defiant Clearance ChartUnprotected Surfaces Protected Surfaces Defiant Clearance DiagramsStove Heat Shields Rear heat shield installed on the Defiant StoveDefiant With Rear Heat Shield only Distance from the Center of the Flue Collar to the WallAssembly Defiant Controls OperationAssemble the Removable Insert Handle Single Air Control Regulates Heat Output and Burn TimeDamper Directs Air Flow Within the Stove Two Ways to Add FuelAndirons Help Protect the Glass Infra-Red Reflective Glass Panels For Clear Fire ViewingBurn Only High-Quality Wood Surface Thermometer is a Valuable Guide to OperationUse the Air Control Settings that Work Best for You Defiant Control SettingsHigh-Efficiency Wood Burning With Catalytic Combustion Starting and Maintaining a Wood Fire Conditioning Your StoveAdd larger pieces of wood as the fire begins to burn Refuel While the Embers Are Still HotAsh Disposal Steel Chimney Masonry ChimneyIndoor/Outdoor Location Flue SizingSingle Venting Draft TestingCreosote FuelConclusion Negative PressureKeep Your Stove Looking New Working Its Best MaintenanceHow to Adjust the Door Latches Adjust the Damper as NeededCheck the Operation Primary Air Shutter Tighten the Damper Handle as NeededWhen To Suspect a Combustor Problem Inspection and CleaningRemoving and Cleaning the Combustor Catalytic ElementRemove the bricks and the brick retainer Replace the Stove Gaskets as Needed Adjust the Door Latch If Necessary Annual MaintenanceChimney System Permanent Defiant GasketsMasking and Poisoning BlockageFlame Impingement OverfiringFor a fireplace Appendix Chimney and Fireplace HazardsDefiant Woodburning Stove Defiant Warranty Vermont Castings Majestic Products Company